Rowenta DG8626F0 Steam Pro Iron User’s Guide

Rowenta DG8626F0 Steam Pro Iron

Product Overview

PREPARATION

Safety lock (according to model)

• Your steam station is equipped with a safety lock that holds the iron onto the base unit in order to facilitate transport and storage:
• Pull up
• Push down

The safety lock allows you to carry your steam station by the iron handle:

• Place the iron on the iron rest of the steam station and lock it into place (you will hear an audible “ click ” sound)
• Hold the iron by its handle in order to transport your steam station

Water recommendations

Tap water

• Rowenta steam stations are designed to be used with UNTREATED TAP WATER. If your water is very hard, Rowenta recommends mixing half untreated tap water with half distilled water which reduces the hardness.

Softened water

• There are many types of household water softeners and the water from many of them is perfectly acceptable for use in the steam station. However, some types of softeners, particularly those that use chemicals such as salt, can cause the appliance to leak or spit during use, this is notably the case with filter jugs. Therefore we would not recommend using this type of water.
• If you experience this type of problem, we recommend that you try using untreated tap water or store-bought distilled water which can be mixed 50% distilled with 50% untreated tap water. Once you have changed the water it will take several uses to correct the problem. Rowenta recommends trying the steam function for the first time on an old towel or cloth that can be discarded to avoid potentially damaging your clothes.

Preparing your steam station

• Place the steam station on a flat, stable, horizontal, and heat-resistant surface
• Lift the removable water tank (located at the front of the steam station) by pressing on the lock screw located on the tank handle
• Fill the tank with untreated tap water, taking care not to exceed the maximum level
• Slide the tank back into its housing until it “ clicks ” into place.
• Unwind the electrical power cord completely and remove the steam cord from its housing
• Plug your steam station into a 120-volt electric outlet

USE

Switching on your steam station

• Press on the on / off switch, and it begins flashing. The green light located on the control panel flashes
• When starting, and regularly while it is being used, your steam station’s electric pump injects water into the boiler. It makes a noise but this is quite normal.
• The steam station and the iron are ready for use when the steam indicator light is on and the iron light goes out.

The first time the appliance is used, there may be some fumes and a slight smell this is not harmful and will quickly disappear.

Operating the control panel

• Flashing green light the water is heating up in the boiler.
• Continuous green light: steam is ready for use.
• Flashing red light: the tank is empty.
• The “ Calc Away System ” or the “ boiler rinse ” orange indicator flashes 1 (according to model): the collector/boiler needs to be rinsed.

Using your steam station

• Place the iron’s temperature control on the type of fabric to be ironed (see table below).

• The iron temperature control light turns on.
  Important: whenever you start using your iron and whenever you reduce the temperature during use, the iron is ready for use when its indicator light goes out and when the green light located on the control panel comes on and remains on.

• During use, when you increase the temperature of the iron, you can start ironing immediately.

ECO Mode

Your steam station has an ECO mode function which uses less power whilst still guaranteeing a sufficient steam output for you to iron your garments properly. In order to use this function, once the thermostat of your iron has been correctly set (see table above), press the ECO button located on the control panel. The ECO mode can be used on all types of fabrics, nevertheless for very thick or very creased fabrics we recommend that you deactivate ECO mode (by pressing the ECO button again) to guarantee the best results.

• During ironing the iron indicator light switches on and off according to heating requirements but this has no effect on use.
• To obtain steam, press on the steam control button beneath the iron handle and keep it pressed. The steam will stop when you release the button.
• Always spray starch on the reverse side of the fabric to be ironed.

Recommendations: To prime the steam circuit, either before using the iron for the first time, or if you have not used the steam function for a few minutes, press the steam control button several times in a row, holding the iron away from your clothes. This will enable any cold water to be removed from the steam circuit.

Iron temperature control setting: Your iron is quick to heat up so start with fabrics to be ironed at a low temperature and finish with those which need higher temperatures.

Mixed fiber fabrics: set the ironing temperature to the setting for the most delicate fabric. For delicate fabrics (•), press the steam control button (under the handle of the iron) intermittently to avoid any water droplets appearing with the steam. If you set your thermostat to “ min ”, the iron will not become hot.

Vertical steam ironing

• Set the temperature of the iron to the max position.
• Hang the garment on a coat hanger and hold the fabric slightly taut with one hand.
• Press repeatedly on the steam control button (beneath the iron handle) moving the iron from top to bottom.

Examples of how to use the vertical steaming function:

• Removing creases directly on hangers from delicate fabrics that you do not want to bring into contact with the hot iron.
• Refreshing a shirt or a suit just before putting it on.

As steam is very hot: never attempt to remove creases from a garment while it is being worn, always hang garments on a coat hanger. For fabrics other than linen or cotton, hold the iron a few centimeters from the garment to avoid burning the fabric.

Warning: Never put the iron state on the table it can burn your table, always put the iron on its stand or left the iron in a standing position

Dry ironing

• Do not press the steam control button.

Fill the water tank again

• When there is no more steam and the “ Water tank empty ” light flashes
• the water tank is empty.
• Remove the water tank using the handle (on the front of the steam station)and fill it do not fill above the Max. level.
• Push the water tank into position until it “ clicks ” into place. Press the Restart button located on the control panel. The red light turns off.
• The steam station and the iron are ready for use when the steam indicator light is on and the iron temperature control light goes out.

Storing the steam station

• Turn off the appliance and unplug it. Place the iron on the iron and rest on the steam station. Lock the iron onto the base unit by pressing it until you hear an audible “ click ”, so your iron is secure (according to the model). Fold the steam cord in two and place it in its housing. Wind up the power cord and attach it to the velcro.
• Leave the steam station to cool for at least one hour before putting it away if it is to be stored in a cupboard or confined space. You can then store your steam station safely.

MAINTENANCE AND CLEANING

Do not use any cleaning or descaling products for cleaning the soleplate or the base unit. Never hold the iron or the base unit under the tap.

• The iron soleplate: Clean the soleplate of your iron when it is cool with a damp cloth or a non-abrasive sponge.
• The base unit: Clean the plastic parts of the appliance occasionally with a soft cloth.
  

Easy descaling of your steam station

Do not use any descaling substances (vinegar, industrial descaling products, etc.) when rinsing the scale collector: they could damage it. Before emptying your steam station, it must always be left to cool for 2 hours to avoid any risks of scalding.

For models with scale collectors.

To extend the life of your steam station and avoid scale on your ironing, your steam station is equipped with a built-in scale collector. This collector, located in the boiler, automatically removes the scale that forms inside.

Operation:

• An orange “ Calc-Away System ” light located 5 on the control panel starts flashing to tell you that the scale collector needs rinsing.
• Once the steam station has cooled completely, remove the scale collector cover

IMPORTANT! This operation must not be carried out unless the steam station has been unplugged for at least two hours and has cooled down completely. To carry out this operation, the steam station must be close to a sink as water may come out of the tank when it is opened.

• Unscrew the scale collector and remove it from the housing; it contains the scale that has built up in the tank.
• To clean the collector properly, just rinse it under running water to remove the scale it contains.
• Put the collector back into its housing and screw it in completely to keep it watertight.
• Put the scale collector cover back on.

The next time you use your iron, press the “ Restart ” button on the control panel to turn off the orange “ Calc-Away System ” light.

In addition to this regular maintenance procedure, we recommend that you rinse the boiler completely once every 6 months, or once every 25 times you use your steam station.

User Support

USA: If this troubleshooting does not resolve the issue, before consulting the retailer or returning the product, please telephone Rowenta Consumer Services at 1-800-769- 3682. Further hints and tips are obtainable from our homepage www.rowentausa.com

Canada: If you are unable to trace the cause of the fault, contact an official Rowenta Customer Service Center. The addresses are shown in the enclosed service center address list. Further hints and tips are obtainable from our homepage: www.rowenta.ca

ROWE-NTA INTERNATIONAL LIMITED GUARANTEE

www.rowenta.com This product is repairable by ROWENTA, during and after the guarantee period. Accessories, consumables, and end-user replaceable parts can be purchased, if locally available, as described on the ROWENTA internet site www.rowenta.com

The Guarantee

ROWENTA guarantees this product against any manufacturing defect in materials or workmanship during the guarantee period within those countries*** as stated in the country list on the last page of the user manual, starting from the initial date of purchase.

The international manufacturer’s guarantee covers all costs related to restoring the proven defective product so that it conforms to its original specifications, through the repair or replacement of any defective part and the necessary labor. At ROWENTA’s choice, a replacement product may be provided instead of repairing a defective product. ROWENTA’s sole obligation and your exclusive resolution under this guarantee are limited to such repair or replacement.

Conditions & Exclusions

ROWENTA shall not be obliged to repair or replace any product which is not accompanied by a valid proof of purchase. The product can be taken directly in person or must be adequately packaged and returned, by recorded delivery (or an equivalent method of postage), to a ROWENTA-authorized service center. Full address details for each country’s authorized service centers are listed on the ROWENTA website (www.rowenta.com) or by calling the appropriate consumer Service center set out in the attached Country List.

This guarantee applies only for products purchased and used for domestic purposes and will not cover any damage which could occur as a result of misuse, negligence, failure to follow ROWENTA instructions, or a modification or unauthorized repair of the product, faulty packaging by the owner or mishandling by any carrier. It also does not cover normal wear and tear, maintenance or replacement of consumable parts, or the following:

• using the wrong type of water or consumable
• damages or bad results specifically due to the wrong voltage or frequency as stamped on the product ID or specification
• scaling (any de-scaling must be carried out according to the instructions for use)
• accidents including fire, flood, thunderbolt, etc
• mechanical damages, overloading
• ingress of water, dust, or insects into the product
• damage to any glass or porcelain ware in the product
• professional or commercial use

Consumer Statutory Rights

This international ROWENTA guarantee does not affect the Statutory Rights a consumer may have or those rights that cannot be excluded or limited, nor rights against the retailer from which the consumer purchased the product. This guarantee gives a consumer specific legal rights, and the consumer may also have other legal rights which vary from State to State or Country to Country. The consumer may assert any such rights at his sole discretion.

Where a product is purchased in one listed country and then used in another listed country, the international ROWENTA guarantee duration is the one in the country of usage, even if the product was purchased in a listed country with a different guarantee duration. The repair process may require a longer time if the product is not locally sold by ROWENTA. If the product is not repairable in the new country, the international ROWENTA guarantee is limited to a replacement by a similar or alternative product at a similar cost, where possible.

FAQ’s

Can I clean the bottom of my iron with a scourer?****

No, this might damage the bottom. Use a moist cloth or a soft sponge to clean it.

What are the differences between a steam iron and a regular iron?****

The biggest advantage of a steam iron is that it removes wrinkles easier due to the use of steam. A regular iron on the contrary is much lighter and often cheaper.

The sole of my iron is discolored, can I still iron with it?****

That is possible, but there is a chance it will rub off on light-colored clothing.

Can I iron over buttons?****

No, this will damage the sole of the iron and that will prevent the iron from working correctly. Never iron over buttons, zippers, or other hard objects.

What is the Rowenta DG8626F0 Steam Pro Iron?

The Rowenta DG8626F0 Steam Pro Iron is a high-performance steam iron that is designed to deliver professional-quality results. It features a powerful steam output, a precision tip for hard-to-reach areas, and advanced features for efficient ironing.

Can I use tap water in the Rowenta DG8626F0 Steam Pro Iron?

It is recommended to use clean, cold tap water in the Row.

My iron does not produce steam, what should I do?

Check that the iron is properly connected to the steam station. If the iron is properly connected, check that the water tank is filled with water. If the water tank is filled with water, check that the safety lock on the iron is unlocked.

The steam station produces a lot of steam but my iron does not get hot. What should I do?

Check that the safety lock on the iron is unlocked. If it is unlocked, check that the water tank is filled with water. If it is filled with water, check that you are using tap water or distilled water in your steam station.

My iron leaks when I use it, what should I do?

Check that you are using tap water or distilled water in your steam station. If you are using tap water or distilled water, check that you are filling your steam station with enough water.

My iron leaks from around its base when I use it, what should I do?

Check that you are using tap water or distilled water in your steam station. If you are using tap water or distilled water, check that you are filling your steam station with enough water and/or checking for leaks from around your iron’s base during use. If this does not resolve the problem please contact our Customer Service Department at www.rowenta-shop.com/en/contact_us.

The power cord of my appliance gets hot during use, what should I do?

This phenomenon may occur if your appliance is used on an electrical circuit shared by other appliances causing an overload and/or a short circuit. In order to prevent this from happening we recommend you connect your appliance directly to a wall outlet and not to an extension cord. If this does not resolve the problem please contact our Customer Service Department at www .rowenta-shop.com/en/contact_us.

My appliance has been exposed to rain; can I still use it?

Yes, provided that there is no damage to the product and it has been used correctly and according to instructions prior to being wetted (see “Using Your Steam Station” section). However, we recommend that you unplug it and let it dry thoroughly before re-using it (see “Cleaning Your Steam Station” section). If this does not resolve the problem please contact our Customer Service Department at www.rowenta-shop.com/en/contact_us.

Download this PDF Link:Rowenta DG8626F0 Steam Pro Iron User’s Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>