ELSEMA PCR433WG Wiegand Output Penta Receiver User Manual

433MHz Receiver Wiegand Output – PCR433
WGWiegand Output Penta Receiver
433MHz Penta Receiver with Wiegand Output
PCR433WG

Features

• Easy to add remote controls to any Wiegand input access control panel
• Remotes are added like cards or RFID tags with no software changes
• Wireless keyless entry offers convenience, security and safety for accessing gates, doors and boom gates
• Wide operating supply voltage and low current consumption
• Easy way to facilitate for handicapped access
• Compatible with PentaCODE ® remotes
•  Easy to use dipswitch coding

Applications

• Keyless access control for automatic gates, doors, and boom gates

Description

This receiver allows you to add wireless remote controls to your existing access control systems by connecting the PCR433WG receiver to the access system. The remote controls have a range of up to 200 meters (650 feet) and are available with 2 or 4 buttons. The extra buttons can be used as a panic button allowing a single remote to allow access control and a panic alert system.
The receiver Wiegand output interfaces to virtually any commercial access control panel. Remote controls are added as easily as Wiegand cards or RFID tags without any software changes. The ID and facility codes can be matched to the system requirements.
The receiver has a bi-color LED to act as a status display. Red LED indicates that AC or DC power is “On” and Green LED indicates remote control signal has been received.

Setup Instructions

The Penta receiver has a 12-way dipswitch, where switches 1-8 sets the site code. Dip Switch 10, 11 & 12 selects the button that the PCR433WG receives from the PentaCODE ® Remote.

| Receiver dip-switch setting
---|---
Remote Button| 10| 11| 12
All| Off| Off| Off
1| Off| Off| On
2| Off| On| Off
3| Off| On| On
4| On| Off| Off

The user code is set by the 12-way dipswitch on the remote. Each remote should have a unique code to identify each user. Remotes are programmed into the access controller in the same way as RFID tags. When programming instead of swiping the RFID tags, the remote button is pressed. On the PentaCODE ® remotes you need to have at least 1 of the 12 switches “On” for the remote to work. The receiver comes pre-wired in a small 70 x 55 x 25 mm enclosure and a supply of 12 to 24 Volts AC or DC can be connected.

Products in the Range

| | |
---|---|---|---
PCR43301RE
1-Channel Receiver with Relay Output.
Enclosed in a case| PCR43302P
2-Channel Plug-in type
Receiver with Open
Collector Output| PCR43302R
2-Channel Receiver with
Relay Outputs| PCR43302RE
2-Channel Receiver with
Relay Outputs. Enclosed
in a case
| | |
PCR43301240R
1-Channel Receiver with240VAC mains supply| PCR43301240RE
1-Channel Receiver
enclosed in an IP66 case| PCR43302240R
2-Channel Receiver with
240VAC mains supply| PCR43302240RE
2-Channel Receiver
enclosed in an IP66 case
| | |
PCR43304R
4-Channel Receiver with
Relay Outputs| PCR43304RE
4-Channel Receiver
enclosed in an IP66 case| PCR43305R
5-Channel Receiver with
Relay Outputs| PCR43305RE
5-Channel Receiver
enclosed in an IP66 case

LED Indicator

Technical Data

Supply Voltage| 12 — 24 Volts AC or DC. Can use Elsema’s AC power pack (12PP-1000)
---|---
Standby Current| 28mA stand by at 24VDC
Wiegand Format| 26 bits, other formats available upon request.
Frequency Band| 433.100 to 434.700MHz
Operating Temperature Range| -5 to 50°C
Receiver Sensitivity| 0.316uV (-117dBm)
Connections| 50cm Flying leads for supply and Wiegand output. See block diagram
Antenna| ANT433 series for long-range applications. Antenna wire for short- range applications.
Dimensions| 70mm x 55mm x 25mm.
Weight| 70 grams
Operating Range| up to 200 meters depending on building structure and receiver antenna
Useable Transmitters| PCK series “PentaCODE®” remotes.

Block Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>