UVS Z8 Fast Charging Magnetic Wireless Charger User Manual
- June 10, 2024
- UVS
Table of Contents
UVS Z8 Fast Charging Magnetic Wireless Charger User Manual
Preface
Thank you for purchasing our company’s wireless charger product. This product is a desktop wireless charger that allows you to easily experience the fun of wireless charging. Before using this product, please read the instruction manual carefully and keep it properly for future references.
Product List
Wireless charger x1
User manual x1
Product Specifications
| Name | Magnetic Wireless Charger |
|---|---|
| Model | Z8 |
| Output | 10W/7.5W/5W |
| Input voltage | 5V/2A, 9V/2A (QC3.0 or PD protocol) |
| Output voltage | 5-9V |
| Output current | Max-1100mA |
| Charging method | Electromagnetic induction |
| Input port | Type-C |
| 10W max | 82% |
| Charging distance | 0-4mm |
| Working frequency | 110-205KHz |
Instruction
| Working status | LED indicator |
|---|---|
| Connect to power | |
| Standby mode | |
| On charging | |
| Failure | The indicator light flashes quickly |
For fast and safe charging, it is recommended to use a QC3.0 or PD charger, other adapters may not be suitable for this device, which may cause unstable charging or abnormal flickering.
Attentions
- Do not pull the power cord forcibly to prevent the power cord from breaking or falling off.
- Do not use a phone case with a metal back or a phone case with a thickness greater than 4mm
- Do not put metal objects or magnetic cards on the charging board, it may cause the metal to become hot, the magnetic card is damaged, the charger is damaged or other abnormalities.
- The receiving coil of the mobile phone that supports wireless charging is generally located at the center of the mobile phone. Please place the centre of the mobile phone in the centre of the charging board for better charging experience .
- If the receiving coil or the transmitting board are overheated during use and stop charging, please remove the charging device, wait for it to cool down, and try charging again.
- The standard temperature of wireless charger QI is 130°F, but our product temperature is controlled within 130°F. The charger will cut off the current when it is abnormally hot. Please contact us if any damage occurs.
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2)this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. During the operation of
device a distance of 15 cm surrounding the device and 20 cm above the top
surface of the device must be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>