HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker Installation Guide

June 10, 2024
HYPERSPIKE

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig1

Product Information
The LineWave is a versatile speaker system that can be installed both indoors and outdoors. It can operate in 25V, 70V, or 100V distributed audio or 16, 8, or 4 Ohm direct drive applications. The LineWave is available in four different sizes and can be configured with 2, 4, 8, or 16 speakers. It is offered in several color options and is UL 1480A certified when powered as a direct drive unit. When powered with an accessory transformer, it is UL 1480 certified.

Part Number Breakdown

The LineWave is available in the following model configurations:

  • 90243A-801: 2 speakers
  • 90243A-802: 4 speakers
  • 90243A-803: 8 speakers
  • 90243A-804: 16 speakers

Specifications

The LineWave has the following specifications:

  • System Type: Full Range, Column Loudspeaker
  • Operation Mode: 16/8/4 Loudspeaker with Optional Line Matching Transformer
  • Number of Speakers in Array: 2, 4, 8, or 16
  • Maximum Power Draw: 20W, 40W, 80W, or 160W depending on the model
  • Max SPL @ 1m, 18V Direct Drive: 105dB to 123dB depending on the model
  • Peak SPL @ 1m: 113dB to 131dB depending on the model
  • Usable Range @ 80dB, A-Weighted: 17m to 141m depending on the model
  • Input Sensitivity (2.83Vrms/1m): 87.8dB to 94.3dB depending on the model
  • Nominal Impedance: 16 or 8 Ohms depending on the model
  • Vertical Coverage -9dB (Avg. 1kHz-4kHz): 85dB to 97dB depending on the model
  • Frequency Response (+/- 6dB): 16Hz to 20kHz
  • Required Input Signal Processing: None
  • Horizontal Coverage -9dB (Avg. 1kHz-4kHz): 16 or 8 Ohms depending on the model
  • Maximum Input Voltage: 16, 8, and 4 Models
  • Color: Several options available
  • Enclosure Material: Not specified
  • Grille Material: Not specified
  • Input Connection: Not specified
  • Ingress Protection: Not specified
  • Product Dimensions, HxWxD (in): Not specified
  • Net Weight (lbs): Not specified

Product Usage Instructions

When installing the LineWave, make sure to follow these guidelines:

  • For outdoor installation, make sure that the support system used has the proper wind load rating and complies with local standards and codes.
  • Do not disconnect the equipment unless power has been switched off or unless the area is known to be nonhazardous.
  • Exceeding the maximum ratings of the speaker will cause excessive distortion and may cause permanent damage to the speaker and its internal components.

The LineWave can be configured to operate in either indoor or outdoor applications, and can be configured to operate in 25V, 70V, or 100V distributed audio or 16, 8, or 4 Ohm direct drive applications. The LineWave is available in four different sizes and can be configured with 2, 4, 8, or 16 speakers. It is offered in several color options and is UL 1480A certified when powered as a
direct drive unit. When powered with an accessory transformer, it is UL 1480 certified.

ORIGINAL ISSUE DATE RELATED TO MOUNTING AND WIRING DIAGRAM ONLY. CHANGE TO ISSUE DATE WILL AFFECT RELATED LABELS

WARNING
EXPORT, RE-EXPORT, AND TRANSFER OF THIS TECHNICAL DATA IS REGULATED BY US EXPORT ADMINISTRATION REGULATIONS AND MAY BE SUBJECT TO LICENSING REQUIREMENTS FROM THE BUREAU OF INDUSTRY AND SECURITY.

CAUTION: EXCEEDING THE MAXIMUM RATINGS OF THE SPEAKER WILL CAUSE EXCESSIVE DISTORTION AND MAY CAUSE PERMANENT DAMAGE TO THE SPEAKER AND ITS INTERNAL COMPONENTS.

Introduction

Designed with the latest technology in line array speaker systems, the HyperSpike® LineWave is optimized to produce clear and authoritative voice commands and powerful tones never before possible within reverberant environments. The beam forming capability of the LineWave speaker allows even coverage across the listening plane while focusing the acoustic pattern away from surfaces that cause unwanted reflections. This technology is essential for achieving optimum levels of speech intelligibility within reverberant spaces. The result is clear and intelligible direct sound that ensures critical messages are heard and understood.
The LineWave is ready to be installed in either indoor or outdoor applications, and can be configured to operate in 25V, 70V, or 100V distributed audio or 16, 8, or 4 Ohm direct drive applications. Available in four different sizes, the LineWave offers exceptional scaling capabilities for any size installation.

Part Number Breakdown
The LineWave is available with either 2, 4, 8, or 16 speakers and is offered in several color options. The following breakdown describes the model number configurations:

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig2

  • Note: The LineWave speaker is UL 1480A certified when powered as a direct drive unit. When powered with accessory transformer 72575B-80X or 72542B-80X the unit is UL 1480 certified.

LineWave Specifications

System| 90243A-801| 90243A-802| 90243A-803| 90243A-804
---|---|---|---|---
Type| Full Range, Column Loudspeaker
Operation Mode| 16/8/4Ω Loudspeaker with Optional Line Matching Transformer
Number of Speakers in Array| 2| 4| 8| 16
Maximum Power Draw:

16Ω, 8Ω, and 4Ω Models

| 20W| 40W| 80W| 160W
Max SPL @ 1m, 18V Direct Drive| 105dB| 111dB| 117dB| 123dB
Peak SPL @ 1m| 113dB| 119dB| 125dB| 131dB
Usable Range @ 80dB,

A-Weighted

| 17m (56ft)| 35m (115ft)| 70m (230ft)| 141m (463ft)
*Reverb SPL @ 10 ft, 18V Direct Drive*| 87.8| 91.7| 94.3| 95.7
Anechoic SPL @ 3m, 18V Direct Drive| 93.4| 98.0| 103.0| 104.0
Input Sensitivity (2.83Vrms/1m)| 85dB| 91dB| 97dB| 103dB
Nominal Impedance| 16Ω| 8Ω| 4Ω| 4Ω, 2 Channel
Vertical Coverage -9dB**

(Avg. 1kHz-4kHz)

| 99°| 45°| 21°| 10°
Frequency Response (+/- 6dB)| 250Hz-15kHz
Required Input Signal Processing| High Pass at 200Hz – Direct Drive Models Only
Horizontal Coverage -9dB

(Avg. 1kHz-4kHz)

| 187°
Maximum Input Voltage: 16Ω, 8Ω, and 4Ω Models| 18V RMS, 36V Peak
Color| Black, Red, White, Silk Grey
Enclosure Material| Aluminum
Grille Material| Steel
Input Connection| SJOOW Cable, 6ft. Provided
Ingress Protection| Indoor and Outdoor Applications
Product Dimensions, HxWxD (in)| 6.6 x 4.9 x 2.9| 12.3 x 4.9 x 2.9| 23.7 x 4.9 x 2.9| 46.5 x 4.9 x 2.9
Net Weight (lbs)| 2.6| 4.3| 7.5| 14.7

Line Wave UL Directional Characteristic

  90243A-801 90243A-802 90243A-803 90243A-804
HORIZONTAL AXIS -3Db Angle +/- 35° +/- 40° +/- 40°
-6Db Angle +/- 65° +/- 70° +/- 70° +/- 75°
SPL @ +/- 90° 86.2 dBA 90.8 dBA 95.2 dBA 98.2 dBA

VERTICAL AXIS

| -3Db Angle| +/- 35°| +/- 20°| +/- 10°| +/- 10°
-6Db Angle| +/- 65°| +/- 45°| +/- 25°| +/- 20°
SPL @ +/- 90°| 86.2 dBA| 88.2 dBA| 89.3 dBA| 88.3 dBA

LineWave Transformer Specifications

System 72575B-801 72542B-801 72542B-802
Type Optional Transformer
Operation Mode 25 / 70 /100 Watt Tap Settings
Line Wave Compatibility 90243A-801/802 90243A-803 90243A-804
Maximum Power Draw: 30W 85W 170W

Maximum Supervisory Voltage:

25V/70V/100V Models

| 32V DC
Enclosure Material| Plastic
Ingress Protection| Indoor/Outdoor
Product Dimensions, HxWxD (in)| 5.9 x 5.9 x 3.9| 9.8 x 5.9 x 3.9| 9.8 x 5.9 x 3.9
Net Weight| 3lbs| 4.5lbs| 6.5lbs

Installation

  • LineWave speakers are by default configured as 4Ω, 8Ω, or 16Ω loudspeakers, however, an optional line matching transformer is available if it is desired to connect the LineWave to a Distributed Audio system. LineWave loudspeakers are approved for use with 25V, 70V, and 100V amplifiers. When configured for 25V, 70V, or 100V input, the LineWave includes a DC blocking capacitor to facilitate DC speaker supervision.
  • All LineWave systems utilize an outdoor rated SJOOW cable for electrical connections. To connect your LineWave speaker to an amplifier, route the cable to an appropriate junction box, or other connector, as approved by local electrical codes and standards. For ease of installation into a junction box, a Strain-Relief Cord Connector is included.
  • Note: In the United States reference National Electrical Code (NFPA 70) and National Fire Alarm and Signaling Code (NFPA 72) for installation standards.
  • Note: In Canada reference CSA C22.1, Canadian Electrical Code, Part 1, Safety Standard for Electrical Installations, Section 32, for installation standards.

4Ω, 8Ω, and 16Ω System Overview
LineWave Models 90243A-801, 90243-802, and 90243A-803 (16Ω, 8Ω, and 4Ω respectively) provide a six foot SJOOW-18/2 cable for amplifier interconnection. Refer to the images in this section for polarity information.
LineWave Model 90243A-804 provides a six foot SJOOW-18/4 cable wired as two 4Ω channels for amplifier interconnection. If your amplifier is capable of driving a 2Ω load, these channels may be tied in parallel on a single amplifier channel. Refer to the images in this section for polarity information.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig3

Distributed Audio System Overview
An optional 25V/70V/100V transformer allows the LineWave to be connected to 25V, 70V, or 100V distributed audio networks. It has four field-selectable power taps on the provided terminal block that allow the output SPL to be tuned to specific applications. The 25V/70V/100V transformer assembly also has an integrated DC blocking capacitor that allows amplifiers to conduct DC circuit supervision. The taps can be selected by wiring 25/70/100V input lines to the appropriate terminal block contacts, as shown in the wiring diagrams included in this section. Once the system is mounted, reference Section 3 for tables detailing the power draw and output SPL of LineWave speakers when using the available transformer tap settings.
Note: Section 1.2 lists the 25V/70V/100V transformers which are available for each model of LineWave loudspeaker.
Note: Terminal Block is rated for 22-14AWG wire

25V/70V/100V Transformer – Recommended Hole Locations and Alignment
In order to connect the LineWave’s SJOOW cable to the transformer assembly, utilize the included Strain-Relief Cord Connector. This connector requires a 0.740” hole to be drilled in the transformer assembly. Consult the following recommended hole locations before drilling

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig4 HYPERSPIKE
LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig5

The orientation of the transformer cover is important to maintaining a water tight seal. Refer to Figure 5 to confirm alignment before replacing the transformer cover.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig6

72542B-80X Circuit Breaker Reset
Transformer 72542B-80X has an integrated circuit breaker that protects itself from line surges and short circuits. The circuit breaker is located inside the transformer housing near the capacitor. If the breaker would trip, follow the steps below:

  1. Remove the transformer housing lid.
  2. Push to reset the breaker (the button on the breaker should push in and stay).
  3. Install the transformer housing lid.

Wall Mounting
Hardware intended to mount LineWave loudspeakers to a wall surface is included with every purchase.

System| 90243A-801| 90243A-802| 90243A-803| 90243A-804
---|---|---|---|---
Number of Speakers in Array| 2| 4| 8| 16
Model Number of Included

Wall Mounting Kit

| 72544B-802| 72544B-802| 72544B-801| 72544B-801

The following tables list the hardware included in the 72544B-801 and 72544B-802 wall mounting kits.

72544B-801 Wall Mounting Kit

PART DESCRIPTION QUANTITY
A PIVOT NUB 3
B L BRACKET 2
C TIE BAR 2
D 1/4″ WASHER 6
E 1/4″-20 x 1-5/8″ SCREW 2
F 1/4″-20 LOCK NUT 3
G 1/4″-20 x 5/8″ SCREW 1
H 1/4″-20 T NUT 4
J 1/4″-20 x 1″ SCREW 4
K 1/4″-20 x 1″ SET SCREW 1

72544B-802 Wall Mounting Kit

PART DESCRIPTION QUANTITY
A PIVOT NUB 1
B L BRACKET 1
D 1/4″ WASHER 1
G 1/4″-20 x 5/8″ SCREW 1
H 1/4″-20 T NUT 2
J 1/4″-20 x 1″ SCREW 2

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig8

72544B-802 – Wall Mounting Kit Installation:
Reference the following instructions to install a LineWave 90243A-801 or 90243A-802 on a wall surface:

  1. Fasten L Bracket (Part B) to the wall surface using appropriate fasteners for the wall, according to local codes and safety practices. Wall fasteners are not included in the mounting kit.

  2. Insert two T-Nuts (Part H) into the slot on the back of the LineWave and attach Pivot Nub
    (Part A) using two 1” long screws (Part J).

  3. Mount the LineWave by connecting Pivot Nub to L Bracket using flat washer (Part D) and 5/8 long screw (Part G).

  4. To aim the speaker left or right, loosen the 5/8 long screw (Part G) and pivot the unit to the desired position. Once the speaker is in the appropriate position, re-tighten screw.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig9

72544B-801 – Wall Mounting Kit Installation:
Reference the following instructions to install a LineWave 90243A-801 or 90243A-802 on a wall surface:

  1.  Fasten two L Brackets (Part B) to the wall surface using appropriate fasteners for the wall. Always follow local codes and safety practices. Wall fasteners are not included in the mounting kit.
    a. 90243A-803 – L Bracket recommended spacing is 20” apart.
    b. 90243A-804 – L Bracket recommended spacing is 43” apart.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig10

  1. Attach two Tie Bars (Part C) to Pivot Nub (Part A) using two flat washers (Part D), 1-5/8” long screw (Part E), and lock nut (Part F) as shown in Figure 9.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig11

  1. Attach Pivot Nub Assembly from Step 2 to the top L-Bracket using flat washer (Part D) and 5/8 long screw (Part G).

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig12

  1. Insert four T-Nuts (Part H) into the slot on the back of the LineWave and attach two Pivot Nubs (Part A) 1” from each end, using four 1” long screws (Part J). On the bottom Pivot Nub install set screw (Part K) as shown in Figure 11.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig13

  1. Lift the LineWave with Pivot Nubs and insert Set Screw into the hole of the bottom L Bracket.
    While still holding the LineWave, fasten the top Pivot Nub to the Tie Bars from step 1, using 1-5/8” Long Screw (Part E), two Flat Washers (Part D), and Lock Nut (Part F).

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig14

  1. To aim the speaker left or right, loosen the top screw and pivot the unit to the desired position as shown in Figure 13. Once the speaker is in the appropriate position, retighten screw. Pan angle is adjustable within +/- 50°.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig15

  1. To aim the speaker down, loosen (but don’t remove) the two bolts fastening the top Pivot Nub to the LineWave. Slide the Pivot Nub up and down to adjust the tilt angle to the desired orientation as shown in Figure 14. The LineWave may need to be temporarily rotated left or right in order to access the screws.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig16

  1. Once the desired orientation is achieved, tighten all fasteners. Install flat washer (Part D) and lock nut (Part F) onto bottom set screw.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig17

Pole Mounting
An optional Pole Mounting Kit (HyperSpike® item number 72581B-801) is available for LineWave models 90243A-803 and 90243A-804, which allows mounting to poles ranging from 3-7” in diameter. This kit is used in conjunction with the wall mounting hardware supplied with the speaker unit.
The following table lists the hardware included in the 72581B-801 Pole Mount Kit.

72581B-801 Pole Mounting Kit

PART DESCRIPTION QUANTITY
D 1/4″ WASHER 8
F 1/4″-20 LOCK NUT 4
L POLE MOUNT BRACKET 2
J 1/4″-20 x 1″ SCREW 4
M STRAP 4

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig18

Follow these steps to install a LineWave using the Pole Mounting Kit

  1. Fasten L Bracket (Part B) of the wall mount kit to the Pole Mount Bracket (Part L) using two flat washers (Part D), two lock nuts (Part F), and two 1” long screws (Part J). Repeat process with second bracket.

  2. Fasten the Pole Mount Bracket assembly to pole using straps (Part M).
    a. 90243A-803 – L Bracket recommended spacing is 20” apart.
    b. 90243A-804 – L Bracket recommended spacing is 43” apart.

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig20

  1. Proceed with mounting and adjusting the angle of the speaker unit as described in Section 2.6.

25V/70V/100V Power and SPL Specifications

Use the Power Draw and SPL Output tables in this section to select the LineWave model and drive level appropriate for your application. Once a specific tap is selected, reference the included wiring diagrams during installation.

72575B-801 – Power Draw and Output SPL


Model Number

| Input Voltage RMS| Tap Color| Power Draw, Watts| dB SPL Max 1M,

A-Weighted

| * dB SPL Reverb @

10ft

| * dB SPL Anechoic

@ 3m

---|---|---|---|---|---|---







90243A-801

| 25V| Blue| 0.5| 86| 72.4| 78.2
25V| Orange| 1.3| 91| 77.1| 82.2
25V| Red| 1.6| 92| 78.2| 83.8
25V| Brown| 2.7| 94| 79.9| 85.3
70V| Blue| 3.0| 95| 80.8| 86.3
70V| Orange| 8.3| 100| 84.9| 90.7
70V| Red| 10.7| 101| 85.9| 91.9
70V| Brown| 15.3| 103| 87.2| 92.7
100V| Blue| 5.7| 98| 83.5| 89.1
100V| Orange| 15.3| 103| 87.1| 92.9
100V| Red| 19.5| 104| 88.0| 93.8






90243A-802

| 25V| Blue| 0.8| 92| 75.8| 81.9
25V| Orange| 2.2| 97| 80.5| 86.6
25V| Red| 2.8| 98| 81.6| 87.8
25V| Brown| 4.1| 100| 83.2| 89.4
70V| Blue| 5.3| 101| 84.4| 91.2
70V| Orange| 14.9| 106| 88.6| 94.6
70V| Red| 19.3| 107| 89.5| 95.6
70V| Brown| 27.4| 109| 90.7| 96.9
100V| Blue| 10.3| 104| 87.1| 92.9
100V| Orange| 27.8| 109| 90.9| 96.9

72575B-801 Transformer Wiring Guide – Used for 90243A-801 and 90243A-802

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig21

72542B-801 – Power Draw and Output SPL


Model Number

| Input Voltage RMS| Tap Color| Power Draw, Watts| dB SPL Max 1M,

A-Weighted

| * dB SPL Reverb @

10ft

| * dB SPL Anechoic

@ 3m

---|---|---|---|---|---|---







90243A-803

| 25V| Blue| 1.7| 101| 79.9| 87.8
25V| White| 3.3| 103| 82.9| 91.0
25V| Orange| 6.6| 105| 85.9| 94.3
25V| Yellow| 12.7| 108| 88.5| 96.6
70V| Blue| 12.4| 110| 88.5| 96.6
70V| White| 23.9| 112| 91.2| 99.5
70V| Orange| 46.2| 114| 93.8| 102.0
70V| Yellow| 81.6| 117| 95.8| 104.0
100V| Blue| 23.8| 113| 91.2| 99.0
100V| White| 44.6| 115| 93.6| 101.0
100V| Orange| 83.3| 117| 96.0| 104.0

72542B-801 Transformer Wiring Guide – Used for 90243A-803

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig22

72542B-802 – Power Draw and Output SPL


Model Number

| Input Voltage RMS| Tap Color| Power Draw, Watts| dB SPL Max 1M,

A-Weighted

| * dB SPL Reverb @

10ft

| * dB SPL Anechoic

@ 3m

---|---|---|---|---|---|---







90243A-804

| 25V| Blue| 3.2| 106| 83.3| 92.1
25V| White| 6.3| 109| 86.3| 95.1
25V| Orange| 12.9| 111| 89.3| 97.4
25V| Yellow| 24.3| 114| 91.7| 100.0
70V| Blue| 24.3| 115| 91.8| 101.0
70V| White| 46.6| 118| 94.4| 103.0
70V| Orange| 90.6| 120| 96.8| 105.0
70V| Yellow| 159.3| 123| 98.4| 106.0
100V| Blue| 47.8| 118| 94.5| 103.0
100V| White| 89.1| 121| 96.8| 105.0
100V| Orange| 165.8| 123| 98.7| 107.0

72542B-802 Transformer Wiring Guide – Used for 90243A-804

HYPERSPIKE LineWave Medium Power Indoor Outdoor Mass Notification Speaker-
fig23

Warranty

Ultra Electronics – USSI warrants that its products shall conform to the published specifications as of the date of order and shall be free from defects in material and workmanship.
Upon receipt of the returned product(s), Ultra Electronics – USSI will repair or replace any and all product(s) at its discretion. Ultra Electronics – USSI will not issue a credit for product(s) returned through the Return Authorization process. This warranty is extended to the original purchaser and all subsequent owners, provided a copy of the original dated bill of sale is presented when service is requested under warranty.

HyperSpike® Warranty Period
Such warranty shall extend for a period of one (1) year from the date of shipment from USSI’s facility.

How to Obtain Service Under This Warranty
If your product(s) should require service, please write, phone, fax, or email us at:
Ultra Electronics – USSI 4868 East Park 30 Drive Columbia City, Indiana, USA 46725
PH: 260-248-3665
Email: ServiceDepartment@ultra-ussi.com
Ultra Electronics – USSI will provide a Return Material Authorization (RMA) number so that you can ship the product(s) to our factory. Do not ship the product(s) to us without first obtaining an RMA number. Place the RMA number on all boxes returned to the factory. You are responsible for transporting your product(s) to our factory. We will pay the return shipping charges on all product(s) repaired under warranty.

Failures Not Covered by This Warranty
This warranty covers defects in manufacture only. It does not cover:

  1. damage caused by accident, misuse, abuse, product modification, or neglect;
  2. damage incurred during shipment (you must claim these damages from the carrier);
  3. damage resulting from failure to operate the product in accordance with the instruction manual; or
  4. damage resulting from attempted repairs by unauthorized personnel.

Exclusion of Certain Damages
Ultra Electronics – USSI’s liability is limited to the repair or replacement, at our option, of any defective product(s) and shall in no event include indirect, consequential, incidental, punitive, or special commercial damages of any kind. Some states do not allow the exclusion or limitation of indirect, consequential, incidental, punitive, or special damages so the preceding limitation or exclusion may not apply to you.

Warranty After Repairs
An additional warranty of ninety (90) days will be extended to any parts that were repaired or replaced. The original standard warranty or any extended warranty that was purchased at the original time of sale of the product(s) is still in effect for the remainder of the warranty term.

Ultra Electronics – USSI 4868 East Park 30 Drive Columbia City, IN 46725 USA +1-260-248-3666

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals