U S GENERAL 64452 16 Inch End Locker Owner’s Manual

64452 16 Inch End Locker

Product Information

The product is a locker that can be used for storage purposes. It has a total combined weight capacity of 280 lbs, evenly distributed from bottom up. The locker comes with an end locker and can be mounted on the side of the bottom cabinet. It has a hanging rod support and four shelf brackets that can be installed in the vertical rails inside the locker’s interior for each shelf. The locker comes with a handle that can be attached to either side of the cabinet.

Product Usage Instructions

Assembly Precautions

1. Only assemble the locker according to the given instructions to avoid any hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Ensure that the assembly area is clean and well-lit.
4. Keep bystanders out of the area during assembly.

Use Precautions

5. Do not assemble when tired, under the influence of alcohol, drugs or medication.
6. The weight capacity and other product capabilities apply to a properly and completely assembled product only.
7. Assemble on a flat, level, hard and smooth surface that can safely support a loaded cabinet.
8. Do not sit, stand or climb on the locker as it may tip over and cause serious injury or death.
9. This product is not a toy, nor a toy chest. Do not allow children to play with or near this item.
10. Do not exceed weight capacities evenly distributed from bottom up. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
11. Use the locker only as intended.
12. Inspect the locker before every use and do not use if parts are loose or damaged.
13. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

Assembly and Mounting Instructions

• Read the entire important safety information section at the beginning of the document before setting up or using the product.
• Attach the handle to the door with handle screws.
• Place the hanging rod into the hanging rod supports.
• Install four shelf brackets into the vertical rails in the locker’s interior for each shelf. Ensure that the shelf will rest level.
• Place shelves on shelf brackets.
• To mount the locker, remove the handle from the side of the bottom cabinet.

If any parts are missing or broken during unpacking, do not assemble and call 1-888-866-5797 as soon as possible. Keep this manual and the receipt in a safe and dry place for future reference.

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.

Specifications

• Total Combined Weight Capacity (Evenly distributed from bottom up.): 280 lb

IMPORTANT SAFETY INFORMATION

Assembly Precautions

1. Assemble only according to these instructions. Mount only on side of Bottom Cabinet according to instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the influence of alcohol, drugs or medication.
6. Weight capacity and other product capabilities apply to properly and completely assembled product only.
7. Assemble on a flat, level, hard and smooth surface capable of safely supporting loaded Cabinet.

Use Precautions

TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:

1. DO NOT SIT, STAND OR CLIMB ON THIS ITEM.
2. This product is not a toy nor a toy chest. Do not allow children to play with or near this item.
3. Do not exceed weight capacities, evenly distributed from bottom up. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
4. Do not move or lift while loaded.
5.  Use as intended only.
6. Inspect before every use; do not use if parts are loose or damaged.
7. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

Assembly and Mounting Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.

Assembly

Note: Door can be attached to either side of Cabinet.

1. Attach Handle (1) to door with Handle Screws (2).
2. Place Hanging Rod (11) into Hanging Rod Supports.
3. Install four Shelf Brackets (8) into vertical rails in Locker’s interior for each shelf. Install them so that the Shelf will rest level.
4. Place Shelves on Shelf Brackets.

Mounting

1. Remove handle from side of Bottom Cabinet.
2. Using an assistant, place EMPTY End Cabinet onto either side of Bottom Cabinet, making sure lips on End Cabinet fit securely over edge of Bottom Cabinet.
3. Secure End Cabinet to Bottom Cabinet from the inside, using Mounting Bolts (9).
4. Secure End Cabinet to Bottom Cabinet from underneath, using Mounting Bolts (10).
5. Insert Plugs (12) into holes on other side of Cabinet.

Operation Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.

Fill End Cabinet evenly, from bottom to top. Do not exceed weight capacities.

Maintenance and Servicing

Procedures not specifically explained in this manual must be performed only by a qualified technician.

WARNING

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If any part becomes damaged, have the problem corrected before further use.

1. PERIODICALLY, inspect the general condition of the Cabinet. Check for:
   • loose hardware,
   • misalignment or binding of moving parts,
   • cracked or broken parts,
   • any other condition that may affect its safe operation.
2. Wipe external surfaces of the Cabinet with clean cloth.
3. Lubricate Drawer Slides as needed.

Parts List and Diagram

Parts List

Record Serial Number Here

Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Parts may not be interchangeable.

Specify UPC number when ordering parts:

• Red: 193175452290
• Black: 193175470690
• Blue: 193175470676

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797

Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>