PEAQ PMO S271-IQC 27 Inch LED Monitor User Manual

LED Monitor
PMO S271-IQC
User Manual

PMO S271-IQC 27 Inch LED Monitor

|
---|---

Safety instructions

Important Safety Instructions. Please read the instructions carefully and keep them for later use.
CAUTION
RISK OF ELECTRICAL SHOCK DO NOT OPEN
WARNING: SHOCK HAZARD – DO NOT OPEN
The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons and animals.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the device.
Danger! Excessive sound pressure from earphones and headphones can cause hearing loss. If you listen to loud music for a long time, your hearing may be impaired. Set to a moderate volume.
**** Only use with listed power supplies in  the instruction manual.

• Warning! Please refer the information on the exterior enclosure for electrical and safety information before installing or operating the apparatus.

• Note: If you would like to connect an external device with this product, a good quality shielded cable must be used, which ensures the electromagnetic compatibility of the product and the used cable as a whole.

• This product is only intended to be used as a monitor. For sound playback additional headphones or speakers, possibly with their own power supply, are required. Do not use the product for any other purpose than described in this manual in order to avoid any hazardous situation. Improper use is dangerous and will void any warranty claim.

• For household use only. Do not use outdoors.

• Danger of suffocation! Keep all packaging material away from children.

• Only use under normal room temperature and humidity conditions.

• The product is only suitable for use at moderate degrees of latitude. Do not use in the tropics or in particularly humid climates.

• Do not move the product from cold into warm places and vice versa. Condensation can cause damage to the product and electrical parts.

• Do not use attachments or accessories other than recommended by the manufacturer or sold with this product. Install in accordance with this user manual.

• When installing the product, leave sufficient space for ventilation (minimum 10  cm around the product). Do not install in bookcases, built-in cabinets or the like.

• Do not impede ventilation by covering the ventilation openings with items, such as  newspapers, table-cloths, curtains, etc. Do not insert any objects into the housing, e.g. through the ventilation openings.

• Do not install near any heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat.

• Do not shift or move the product when powered on.

• Do not touch, push or rub the surface of the product with any sharp or hard objects.

• Danger! To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

• The product shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product.

• Care should be taken so that no objects or liquids enter the enclosure through openings.

• No naked flame sources, such as lighted candles, should be placed on the product.

• Refer all servicing to an authorised service agent. Do not attempt to repair the product yourself. Servicing is required when the product has been damaged in any way, such as the supply cord or plug are damaged, liquid has been spilled, objects have fallen into the product, the enclosure is damaged, the product has been exposed to
  rain or moisture, does not operate normally, or has been dropped.

• Before connecting the product to a socket outlet, make sure the voltage indicated on the product corresponds to your local mains.

•  If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid hazard.

• Regularly check if the supply cord, product or extension cable is defective. If found defective, do not put the product into operation. Immediately pull the plug.

• Place the supply cord and, if necessary, an appropriate extension cable in such away that pulling or tripping over it is impossible. Do not allow the supply cord to hang down within easy reach.

• Do not jam, bend or pull the supply cord over sharp edges.

• The power plug is used as the disconnect device; the disconnect device shall remain readily operable. To completely disconnect the power input, disconnect the mains plug.

• The product may not function properly or not react to the operation of any control due to electrostatic discharge. Switch off and disconnect the product; reconnect after a few seconds.

• Protect the supply cord from being walked on or pinched particularly at the plug, convenience receptacles and the point where it exits from the product.

• Never pull the plug by the supply cord or with wet hands.

• Disconnect the power plug in case of faults during use, during lightening storms, before cleaning and when not using the product for a longer period of time.

• Danger! Before cleaning, switch the product off and disconnect the power plug from the socket.

• When the product has reached the end of its service life, make it defective by disconnecting the plug from the socket and cutting the cord in two.

Intended use

This product is designed as a monitor only. For sound playback additional headphones or speakers, possibly with its own power supply, are required.
The product is not intended for any commercial or industrial use. Do not use it for other purposes. Any other use might lead to damage of the product or personal injury.
The Imtron GmbH assumes no liability for damage to the product, for property damage or for personal injury due to careless or improper usage of the product, or usage of product which does not meet the manufacturer’s specified purpose.
Before first time use
Remove the product and accessories carefully from the original packaging. It is recommended to keep the original packaging for storage. If you wish to dispose of the original packaging, please observe applicable legal provisions. Should you have any questions regarding proper disposal, contact your local waste management center. Inspect the delivery contents for completeness and damages. Should the delivery contents be incomplete or damaged, contact your sales outlet immediately.
Controls and components
A. Stand
B. On/off multifunction switch
C. Screen
D. DC jack
E. USB-jack with charging function (5 V /1 A)
F. Headphone jack
G. DP input
H. HDMI input

Accessories

1 x Monitor
1 x HDMI cable
1 x Power adaptor
1 x Stand
3 x Screws
1 x User manual
1 x Quick manual
1 x Warranty card

Installing the stand
Mount the base and stand neck with the supplied matching screws. Now mount the stand neck to the appropriate place on the back of the monitor with the screws provided. Put the cover cap on the screw connection.
Connections
POWER SUPPLY
Insert the DC plug of the power adapter into the DC jack on the back of the monitor.
HDMI, or DP connection
Connect the appropriate connectors on the back of the monitor to your computer or other suitable players using appropriate cables.
Note: If you would like to connect an external device with this product, a good quality shielded cable must be used, which ensures the electromagnetic compatibility of the product and the used cable as a whole.
HEADPHONE CONNECTION
Connect the headphones to the Headphone jack of the device.
Note: For sound reproduction additional headphones or loudspeakers, possibly with their own power supply, are required.
Attention
Danger! Excessive sound pressure levels from ear buds and headphones can cause hearing damage. Listening to loud music for extended periods of time may lead to hearing impairment. Keep the volume at reasonable levels.

Operation

TURNING THE UNIT ON/OFF
Press the ****button to switch on the unit.

Note:

• In Off mode (menu setting Reset and Time Off), the monitor will switch on automatically ,when the connected PC/notebook is started.
• If you didn’t press any key within 4 hours, the Monitor will power off automatically. You can reset the power off time individually from OFF / 0 to 24 under the menu setting Reset.
• Display time: A count-down time of 60 seconds will be started before turn off. On the display it will shows: XX (60-0) second to power off, please push any key to cancel.

General settings

MENU SETTINGS
With the device switched on, press the multifunction switch to the left. The main menu opens. Press the multifunction switch up or down to select the desired submenu. To confirm your selection, press the multifunction switch again to the left. You can change the settings by pressing the multifunction switch up or down. Confirm the setting by pressing the multifunction switch again to the left. By pressing the multifunction switch to the right, you return to the corresponding upper menu. To close the main menu, press the multifunction switch to the right until it closes.
The following main menu options are available:

• Luminance

  Brightness
  Contrast
  Eco Mode
  DCR
  Overdrive

• Image Setup

  Image Ratio

• Color Setup

  Color Temp.
  Red
  Green
  Blue

• OSD Setup

  Language
  H. Position
  V. Position
  Timeout
  Transparence

• Reset

  Reset
  Off Timer

• Extra

  Input Select
  Volume
  AMD FreeSync

Set menu language
The menu may be preset to English.
For easy use of the self-explanatory menu, it is advantageous to set it to the respective native language. Proceed as follows:

1. With the monitor turned on, press the multiselector switch to the left.
2. Select the OSD Setup item by pressing the multi-selector up / down. Confirm the selection by pressing the multifunction switch to the left.
3. The first point is Language. Press the multifunction switch to the left to enter the language selection menu.
4. Select the desired language by pressing the multi-function switch up / down. Confirm the selection by pressing the multifunction switch to the left.
5. The desired language is now set. To exit the menu, press the multifunction switch several times to the right.

Reset settings to factory settings

1. With the monitor turned on, press the multifunction switch to the left.
2.  Select the Reset menu item by pressing the  multifunction switch up / down. Confirm theselection by pressing the multifunction switch to the left.
3.  If necessary, select Reset by pressing the multi-function switch up / down. Press the multifunction switch to the left to confirm the reset. All previously made individual settings have now been reset and the menu is closed.

Change image format

1. While the monitor is on, press the multifunction switch down until the desired format is selected.
   You can choose between 4:3 and 16:9.

2. Confirm the selection by pressing the multifunction switch to the left or wait a few seconds until the symbol disappears.

Select input

1. With the monitor turned on, push the multifunction switch to the right.
2. Select the desired input, DP or HDMI by pressing the multifunction switch right.
3. Confirm the selection by pressing the multifunction switch to the left.

FreeSync
The “freesync” function can reduce blurring, ghosting and juddering, and can also reduce lag with videos, games and any other fast-moving content.
To activate the “Freesync” function, the computer display card required to fulfill one of the below minimum requirements:

1. AMD APU and independent video card can support this function;
2. NVIDIA video card can only be supported by DP 1.2 port using NVIDIA GeForce 10 Series or above.

Set picture characteristic

1. With the monitor turned on, press the multiselector switch up until the desired characteristic has been set. You can choose from:.
   | FPS Gaming
   ---|---
   | Low blue light mode
   | Movie mode
   | Reading mode
   | RTS Gaming mode
   | Standard mode
2. Confirm the selection by pressing the multifunction switch to the left or wait a few seconds until the symbol disappears.

Cleaning and Care

• Always unplug the power supply from the power outlet before cleaning.
• Caution! Water must not enter the device.
• Clean the housing with a slightly damp cloth. Clean the display with special screen cleaning cloths. Always check the instructions of the cleaning agent. Certain agents might not be suitable for cleaning this product.
• Do not use any sharp, abrasive or aggressive cleaning agents.
• Do not use any chemicals (e.g. gas, alcohol) to clean the housing.

Disposal

Do not dispose of this appliance as unsorted municipal waste. Return it to a designated collection point for the recycling of WEEE. By doing so, you will help to conserve resources and protect the environment. Contact your retailer or local authorities for more information.

Troubleshooting

If there are any problems during operation, please refer to the following table. If problems cannot be solved as indicated under Solution, please contact your manufacturer.

light is on, check the signal input; if the light is off, check the power supply
Dim image| •Brightness and contrast too low| •Adjust the brightness and contrast
No Sound| •Headphone/ Speaker not connected
•Computer audio setting wrong| •Check the connection of head phone/ speaker
•Check the audio setting of computer
Wrong or abnormal colors| •Loose or broken pins in the cable connector| •Check the HDMI or DP cable to make sure it is in good condition and securely connected

Technical Data

Model
Power supply PMO S271-IQC
Rated input : 12 V 3 A
Rated Frequency: DC
Normal operation : 26 W ±10%
Standby-operation : ≤0.3 W
Off mode  : NA
Adaptor Manufacturer : DONGGUAN YIDAI POWER TECHNOLOGY CO., LTD.
Imported by : Imtron GmbH Wankelstraße 5, 85046 Ingolstadt, Germany.
Commercial registration number : HRB 4580
Model : YD-ZN1200300-6A
Input voltage : 100 – 240 V~
Input AC frequency : 50/60 Hz
Output voltage : 12.0 V
Output current : 3.0 A
Output power : 36.0 W
Average active efficiency : 89.1 %
Efficiency at low load (10 %) : 85.8 %
No-load power consumption : 0.10 W
Display
Screen Panel Type : IPS
Backlight : Edge-LED
Panel size : 27”
Picture Format : 16:09
Pixel distance : 0.2331 (H) x 0.2331 (V)
Contract ratio (Dynamic) : 1M:1
Response time (typical) : 14 ms
Response time (Overdrive) : 5 ms
Optimal resolution : 2560 x 1440
Viewing angle : ≥178 (H), ≥178° (V)
Flicker free : yes
Display color : 16.7 M
Refresh rate : 75 Hz
sRGB : 99%

Connections
Signal input : HDMI/ DP
Signal output : Audio output
**** Use the link https://eprel.ec.europa.eu/ to access the European product database (EPREL), in which more information about the product is saved. Type in the EPREL- registration number 776753 (PMO S271-IQC), or simply scan the QR-code on the energy label to access the model information.

**** Imtron GmbH
Wankelstraße 5
IM_PMO S271-IQC_210804_V03
85046 Ingolstadt Germany
www.imtron.eu
www.peaq-online.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>