Westinghouse Outdoor Power Equipment PWSCSS Surface Cleaner Westinghouse Pressure Washers User Manual

Westinghouse Outdoor Power Equipment PWSCSS Surface Cleaner Westinghouse

Pressure Washers

Product Specifications

• Product Name: PWSCSS Surface Cleaner
• Compatible with Westinghouse Pressure Washers up to 4000 PSI
• Flow Rate: 4.0 GPM (2.0 GPM minimum)

Product Usage Instructions

Installing the Surface Cleaner

1. If necessary, remove the nozzle from the end of the lance.
2. Pull back the quick-connect collar and insert the inlet adapter, then push the collar forward to lock.
3. Ensure the surface cleaner is securely locked into the lance before use.

Using the Surface Cleaner

1. Place the surface cleaner on the horizontal surface being cleaned and start the pressure washer.
2. Squeeze the trigger and move slowly, allowing the unit to clean the surface.
3. If swirling or striping occurs, slow down. If issues persist, check for clogged nozzles.

Nozzle Maintenance

1. Turn off the pressure washer and water supply. Release water pressure by pulling the trigger.
2. Disconnect the surface cleaner from the lance by pulling back the quick-connect collar.
3. Clean the nozzles using a nozzle cleaning tool or fine needle.
4. Back-flush the nozzle with a garden hose to remove debris.
5. Reconnect the surface cleaner to the lance and resume cleaning.

Replacing the Filter Screen

1. If water flow issues persist, replace the filter screen.
2. Turn off the pressure washer and water supply. Release water pressure by pulling the trigger.
3. Disconnect the surface cleaner from the lance.
4. Remove the retaining ring and filter screen using a screwdriver or tweezers.
5. Replace the filter screen with a new one. Contact Service Hotline for replacement screens.

Frequently Asked Questions

Q: Can I use this surface cleaner on vertical surfaces?

A: No, this surface cleaner is designed for flat, horizontal surfaces only to prevent injury or damage.

Q: What should I do if I feel a pulsing sensation while using the surface cleaner?

A: This may indicate a clogged or dirty nozzle. Follow the Nozzle Maintenance instructions to clean the nozzles.

PWSCSS SURFACE CLEANER

FOR WESTINGHOUSE PRESSURE WASHERS UP TO 4000 PSI

WARNING

Do not use for commercial use. User must read and understand the operator’s manual for their pressure washer before using this accessory to reduce the risk of injury. Before beginning any cleaning activity, spray the pressure stream in a safe direction to make sure that all accessories are connected properly in order to minimize the danger of injury or property damage. Fits most pressure washers. Before using this attachment, make sure it is compatible and is correctly installed. Risk of fluid injections. Do not point at people, pets, electrical devices, or the unit itself. Wear eye protection designated to conform with ANSI Z87.1. Before adding, replacing, or modifying accessories, turn off the pressure washer, release the water pressure in the trigger handle, and lock the trigger handle’s lockout (if one is provided with your pressure washer). Use only with cold water and only outdoors. Store the accessory indoors. Save these guidelines. Use them to train other users and refer to them frequently. Give the user of the tool these instructions as well.

PRODUCT SPECIFICATIONS

• Connection……………………………………………1/4 in. Quick Connect Plug Inlet
• Width of Deck………………………………………………………………………….16.5 in.
• Maximum Pressure…………………………………………………………up to 4000 psi
• Minimum Pressure………………………………………………………………….2200 psi
• Maximum Water Flow……………………………………………………………..4.0 GPM
• Minimum Water Flow………………………………………………………………2.0 GPM
• Maximum Water Temperature………………………………………………………194°F

NOTE: Consult your pressure washer’s operator manual for its maximum operating water temperature.

APPLICATIONS

You may use this product for the purpose(s) listed below:

• Cleaning decks, sidewalks, and driveways

INSTALLING THE SURFACE CLEANER

See Figure 1.

• A Inlet adapter

• B Quick connect coupler

• If necessary, remove the nozzle from the end of the lance.

• Pull back the quick-connect collar and insert the inlet adapter. Push the quick-connect collar forward to lock.

NOTE: Be sure the surface cleaner is securely locked into the lance before use.

WARNING

Only use the surface cleaner on flat, horizontal surfaces. To reduce the risk of injection or injury, never lift the surface cleaner from the cleaning surface while operating the pressure washer.

USING THE SURFACE CLEANER

See Figure 2.

• Place the surface cleaner on the horizontal surface being cleaned and start the pressure washer.
• Squeeze the trigger and move slowly allowing the unit to clean the surface

NOTE: Swirling or striping in the cleaned surface indicates you may be moving too quickly. If a slower pace doesn’t stop the condition, the surface cleaner nozzles may be clogged. See Nozzle Maintenance to clean the nozzles. WARNING
Avoid striking any raised obstacles while using the surface cleaner as damage may occur to the unit. If contact occurs and a higher vibration of the unit begins during use, release the trigger and discontinue use. Continuing use could result in serious injury or damage to the unit.

NOZZLE MAINTENANCE

See Figure 3.

The surface cleaner comes assembled. The nozzles are approved for use with pressure washers operating at 2200 to 4000 PSI with a maximum flow rate of 4.0 GPM (2.0 GPM minimum). A pulsing sensation felt while squeezing the trigger and/or a higher vibration in the surface cleaner may be the result of a clogged or dirty nozzle

• Turn off the pressure washer and shut off the water supply. Place unit on the ground and pull the trigger to release the water pressure in the lance.

• Pull back the quick-connect collar to disconnect the surface cleaner from the lance.

• Use a nozzle cleaning tool or a fine needle to free any foreign materials that are clogging or restricting the nozzle.

• Use a garden hose to back-flush the nozzle and force out the debris.
  NOTE: Never point the nozzle outlet at your face.

• Reconnect the surface cleaner to the lance.

• Turn on the water supply and start the pressure washer to resume cleaning.

REPLACING THE FILTER SCREEN

See Figure 4.

If the water still doesn’t flow freely after cleaning the deck nozzles, it may be necessary to replace the filter screen. Replacement filter screens are available by calling our Service Hotline at (855)944-3571.

• Turn off the pressure washer and shut off the water supply. Place unit on the ground and pull the trigger to release the water pressure in the lance.
• Disconnect the surface cleaner from the lance.
• Using a screwdriver or pair of tweezers, remove the retaining ring and filter screen from the inlet plug.
• Once the filter screen is removed from the inlet plug, replace it with a new filter screen (not included).
• Make sure the filter screen is seated inside the inlet adapter and no longer visible above the top of the adapter.
• Reinstall the retaining ring and push into place until it is secure against the filter screen

REPLACEMENT PARTS

Replacement parts are available from our Service Hotline at 855-944-3571.

• Nozzle…………………………………………………………………………..BSSC165A01
• Filter Screen…………………………………………………………………..BSSC165A02

Service Hotline:855-944-3571

• 777 Manor Park Drive, Columbus, OH 43228 and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by MWE Investments, LLC. © 2023 MWE Investments, LLC All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>