MoMi WOODI Baby High Chair User Manual

MoMi WOODI Baby High Chair

Product Information

MoMi WOODI 3-in-1 Chair

The MoMi WOODI 3-in-1 Chair is a versatile and safe chair designed for older children. The product comes with a wooden frame, a seat, footrests, a double tray, and screws for assembly. The chair is designed to be used in three modes: as a high chair, a booster seat, and a chair for older children. The product is covered by a 2-year warranty for the chair and a 6-month warranty for additional equipment.

Product Usage Instructions

1. Assembly of the Wooden Frame:
   • Take the upper (9) and lower (10) parts of the wooden frame and connect them by aligning both parts of the frame with the screw hole. Insert the short screw (11) into the hole and tighten it with an Allen wrench until you feel resistance.
   • Make sure that the holes in the wooden legs are facing in one direction and are forward before assembling the footrests; otherwise, you will not be able to assemble them correctly.
2. Assembly of Footrests:
   • First, insert the smaller footrest into the upper holes on the wooden legs as shown in the picture below. Insert short screws (11) into the buttonholes and tighten them with an Allen wrench. Repeat this step for the larger footrest, which should be placed below the smaller footrest.
3. Assembly of Seat on Swivel Base:
   • Place the seat upside down. Align the screw holes on the top of the swivel base with the corresponding tongues on the bottom of the seat. Insert large screws (15) into all holes and tighten them with an Allen wrench until you feel resistance. Turn the seat over and check that it is securely tightened with the swivel nut by pulling both parts in opposite directions.
4. Assembly of Seat on Wooden Frame:
   • Place the wooden frame in front of you with the footrests in front of you. Hold the seat with the swivel base and place it on the frame so that the front and footrests are in line. Gently lay it on its side, making sure that both parts do not fall apart. Insert large screws (13) into the remaining holes on the wooden frame and tighten them with an Allen wrench until you feel resistance. Check that both parts are firmly connected to each other by pulling the elements in opposite directions.
5. Important Safety Information:
   • Read and follow all instructions carefully to ensure safe use of the product.
   • The person who assembles the chair must be an adult who will use all product components according to the instructions for use and their intended use to prevent child injury.
   • Remove and dispose of all packaging elements that were attached to the product to prevent child injury, such as cardboard elements, plastic films, etc.

Dear Customer,
Thank you very much for buying the MoMi WOODI chair. We hope that the purchased product meets your expectations. Should you have any additional questions, please contact us via www.momi.store  For the sake of children’s safety, please read the manual carefully and follow its recommendations for safe use of the product. It is compulsory for an adult to use all components of the product during assembly in accordance with the user manual and their intended use to prevent injuries.

IMPORTANT

PLEASE READ IT CAREFULLY AND KEEP FOR FUTURE REFERENCE

• Do not leave your child unattended. Never let your child out of your sight
• Always check that the product is safe and stable before use.
• Always use the restraint system.
• Make sure the harness is correctly positioned
• Do not pick up or move the product with the baby inside.
• Do not pick up the product by the feeding tray.
• Do not allow a child to climb onto the product.
• Do not use the product if all its parts are not properly installed and adjusted
• Be aware of the risks posed by open fire or other sources of strong heat, such as electric stoves, gas stoves, etc., near the product
• Be aware of the risk of tipping over if your child is able to push their feet off a table or any other structure
• Do not use the product until the child can sit up unaided.
• To avoid injuries, keep your child away while assembling and disassembling the product.
• The feeding chair is intended for children from 6 months up to 3 years of age, weighing up to 15 kg, who can sit independently.
• The baby chair is intended for children aged 24 to 60 months, weighing up to 20 kg, who are able to sit up unaided.
• Discontinue use of the product if you notice any cracks, tears, or missing parts. In this case, please contact us via the website.
• The product placed under a window may be used by a child as a step and cause them to fall out of the window.
• Do not use any accessories or spare parts other than those approved by the manufacturer.
• Clean with a damp, clean cloth and a mild soap.
• Sheathing and stripes: clean with a damp, clean cloth, do not bleach, do not tumble dry. Do not iron. Do not dry clean.
• When putting in and taking out the baby, lift it up. Children must not be allowed to stand on the footrest and seat cushion, or climb in and out of the high chair.
• The high chair should only be used on a level floor surface.
• The chair is not a toy.
• Do not use the product in any way other than that stated in the instructions
• When the chair is not in use, it should be kept out of the reach of children.
• Placing a baby or heavy objects on the feeding tray may damage the product or harm the baby’s health.
• Never use the product when it is placed on an unstable surface: a platform, a soft surface (eg mattress, pillow), uneven ground, stairs, steps.
• Make sure the harness fits correctly.
• Before your child sits down, make sure that all components are correctly attached and locked.
• Do not expose the product to high and low temperatures as well as high humidity.
• If the chair has been exposed to direct sunlight, place it in the shade and allow it to cool down before using it.
• Do not let your child play around the chair.
• After unfolding the chair, make sure that the lock is working properly.
• The tray is not a safety measure to prevent it from falling out. For this, there are seat belts, which should always be fastened.
• Do not fold and unfold the chair with the baby inside.
• When the tray is not in use, put it in a safe place out of the reach of your child.
• Do not press the tray too hard against the baby. Allow some space to breathe freely.

IMPORTANT: Always remove and dispose of all packaging, films, safety features inside the cardboard box, other plastic components and components that are not approved for use by children. Your child must not have access to any of the packaging elements and plastic films, as this can lead to choking or suffocation. This manual is recommended for future reference, if necessary, to read how to proceed in case of danger or appropriate maintenance.

REMEMBER: The drawings in this manual illustrate the general use of the product and are for illustrative purposes only. The appearance of the product and its components may slightly differ from the actual state.

GUARANTEE

The manufacturer provides a 6-month warranty on additional accessories attached to the product and a 2-year guarantee on the product without accessories.

Components

1. Seat part
2. Crotch
3. Small footplate
4. Large footplate
5. Double tray
6. Turntable
7. Shorter wooden legs
8. Longer wooden legs
9. Top part of the wooden frame
10. The lower part of the wooden frame
11. Short screw M6*45 (5 szt)
12. Large screw M6*65 (4szt)
13. Big screw M8*45(4 szt)
14. Anti-slip screw (4szt)
15. Small turntable screw M8*16 (4szt)
16. Cross nut (4szt)
17. Hexagon key big
18. Hexagon key small
19. Long seatbelts (2szt)

PRODUCT ASSEMBLY

Wooden frame

• Take the top (9) and bottom (10) parts of the wooden frame and connect them by aligning both parts of the frame with the bolt hole. So that the upper part fits into the lower one. Insert a short screw (11) in the hole and tighten it with a suitable Allen key until you feel resistance.

Wooden longer legs

• Fit each of the longer legs with the oval holes located from the center of the leg to the convex parts on each side of the wooden frame. Press the cross nuts (16) into the holes on the sides of the wooden frame so that you can see the “cross” on the pad from the outside. Align them so that the screw can enter them. Insert the long screws (12) into the holes on the upper sides of the legs so that they pass through the anti-slip pads at the same time. Tighten with the smaller Allen key (18) until you feel resistance. If you don’t feel resistance and the screw is turning around, check that the anti-skid washers are turned properly and the screw is fully threaded through them.

NOTE: The wooden legs have holes for the installation of the footrests, make sure that they are facing one direction and are at the front before twisting, otherwise the footrests cannot be correctly fitted.

Footplate

• First, insert the smaller footrest into the upper holes on the wooden legs as shown in the picture be- low. Insert short screws (11) into the buttonholes and tighten with the hexagon key. Then repeat this step for the larger footrest, which should be installed below the smaller footrest.

Assembling the seat on a turntable

• Turn the seat upside down. Then align the screw holes on the top of the swivel pad with the corresponding tabs on the bottom of the seat. Insert the large screws (15) in all holes and tighten with an Allen key until you feel resistance. Rotate the seat and check that it is tightened securely against the swivel washer by pulling both parts in the opposite direction.

Assembling the seat on a wooden frame

• Place the wooden rack in front of you with the footrests at the front. Grasp the seat with the swivel pad and put it on the frame so that the front and footrests are in line. Holding the whole thing, lay it gently on its side, while making sure that both elements do not come apart. Insert the large screws (13) into the remaining holes in the wooden frame and tighten with an Allen key until you feel resistance. Check that both elements are firmly connected with each other by pulling the elements in the opposite direction.

Crotch

• Place the double tray (5) flat, upside down. Then, grasp the leg divider (2) and slide it with the opening to the appropriate place on the bottom of the tray until you hear a “click”, which indicates that the divider is properly installed.

Assembling double tray to seat part

• Hold the tray with one hand by the adjustment button on the bottom. Then, while holding the seatback with your other hand, slide the tray with the appropriate holes on the bottom of the tray onto the armrests of the seat. Align and press by releasing the adjust button. Check that the tray fits into the correct holes by simultaneously pulling the tray and the support in opposite directions. Then adjust the outer tray and slide it over the bottom tray until you hear a click. The outer tray is removable as needed and dishwasher safe.

Assembling textile part

• Put the textile cover on the plastic seat by pulling the fabric over the backrest. Rotate the chair 180 degrees. Pull the seat belts through the slot in the seat and the swivel pad as shown below.

• Once you have completed all of the above steps, turn the chair over and place anti-skid pads (17) on each of the 4 wooden legs.

Seatbelt

• You can change the length of the straps to perfectly match the weight and height of the child. To re-lease the harness press the button on the buckle. The first thing to do after putting the baby in the chair should be to fasten the seat belts and make sure that they fit perfectly: close to the body but not so much that they would restrict the child’s movements.
• Make sure your child’s fingers are kept away when fastening the buckle.

Converting a high chair into a chair for older children

• To convert the highchair into a high chair for older children, follow steps 1-3 above again using the shorter legs (7), you will get the structure as shown in the picture below. Then continue with step 4 and you will then have a complete highchair for older children

Conversion of a highchair into a booster chair

• Use the hexagon key to loosen the screws under the swivel washer that connect the wooden rack to the swivel washer. Small screws on the four ends and medium screws in the center of the wooden rack to detach it from the swivel washer as shown in the picture below.

• Place the booster chair to the correct chair (see minimum chair dimensions below). Use the safety belts (19) included in the kit to attach the chair to the bottom and backrest of the chair you want to mount. Fasten the safety buckles and tighten the retaining strap by pulling on the free end. Make sure the belts are tight and there is no slack.

360-degree rotation of the feeding chair

Press the button on the front of the swivel pad, then while holding the backrest, rotate the chair until you get 360-degree rotation. There are 8 items to choose from, you can choose the most convenient one for your current use. During rotation, you must pay special attention to whether the swivel washer is properly seated.

Produkt spe*nia wymagania norm i standard6w Unii Europejskiej pod wzgledem bezpieczehstwa prduktu oraz zezwolenia na jego uzytkowanie. The meets the requirements of the European Union norms and standards in terms of product safety and permission to use it.
Producent/Producer
TelForce0ne S.A., ul. Krakowska 119, 50-428 Wroc}aw, Poland Wyprodukowano w / Made in PRC

WWW.MOMI.STORE

References

• Momi

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>