MoMi Iris Tricycle Instruction Manual

MoMi Iris Tricycle

Instruction

Dear Customer,
Thank you very much for purchasing the MoMi IRIS tricycle. We hope that the purchased product meets your expectations.
If you have additional questions, please contact us via the website www.momi.store
In the interest of children’s safety, please read the operating instructions carefully and follow its recommendations in order to use the product safely. The person performing the assembly must be an adult who will use all the components of the product in accordance with the instructions for use and their intended use in order to prevent injuries to the child.

IMPORTANT: Remember to remove and throw away all the packaging elements that were attached to the product, so that they do not remain within the reach of a child (e.g. cardboard elements, plastic films, etc.). This could cause a risk of harm, e.g. choking on the child, suffocation for the child. We recommend that you keep this manual for future reference, to read, if necessary, what to do in the event of an emergency or for proper maintenance.

PLEASE NOTE: Drawings and photos are for reference only. The actual appearance of the product may differ from the visualization in the manual.
IMPORTANT! PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
SAFETY NOTES AND PRECAUTIONS
WARNING!:

• For use only under adult supervision, always keep the child in sight of an adult.
• Following the instructions ensures safe use of the product. Please read carefully before using the bicycle and keep it for later use. Recommended for children from 9 months of age.
• Use personal protective equipment, ie helmet, gloves, knee and elbow pads. The product is intended for outdoor use. Do not use in traffic. The tricycle should not be used in the vicinity of motor vehicles, street, swimming pool, hills, roads, stairs, slopes.

The bicycle should be used on flat and unobstructed surfaces.

• Continuous adult supervision is required to avoid serious injury.
• In order to avoid falls and injuries to the user or third parties, parents / guardians should advise children to observe precautionary measures. Before using the product, explain to children about the safe use of the product.
• Always wear shoes when using the product.
• Installation should always be performed by an adult. Before each use, check that the article is not damaged and has no signs of wear, check that all connecting elements and fasteners fit well. Make sure that the bolts and nuts retain their self-closing properties. Check that the set is complete and undamaged. If you find that any parts are missing or damaged, do not use the product and contact your seller.
• Be careful when using ride-on toys, driving skills are required to avoid a fall or collision that could injure the user or a third party.
• The safest areas for riding a tricycle are areas with limited or disabled car traffic, such as: private areas, playgrounds, school playgrounds, recreational areas.
• This product is intended for a single user with a maximum weight of 25 kg.
• Retain packaging or dispose of according to local regulations.

For the safety of children, do not leave freely accessible parts of the packaging (plastic bags, cartons, etc.). Danger of suffocation!

• Check and maintain the bicycle regularly. Before each use of the bicycle, make sure that it is not damaged and that no parts are missing or loose.
• Do not use the bike near bodies of water or other obstacles.
• Do not use the vehicle in the dark or in bad weather.
• It is forbidden to pull the bicycle behind a car or other vehicle.

MAIN PARTS

1. Canopy
2. Pushbar
3. Handlebar grip
4. Handrail
5. Handlebar
6. Seat
7. Frame
8. Rear basket
9. Fender
10. Rear wheel
11. Front wheel
12. Pedal
13. Footrest

PARTS TO ASSEMBLING

1. Seat
2. Frame
3. Front wheel
4. Rear basket
5. Canopy
6. Backrest
7. Upper push bar
8. Plastic of steering
9. Fender
10. Lower push bar
11. Steering rod
12. Pedestal
13. Rear whhel
14. Handrail
15. Handlebar

PRODUCT ASSEMBLY

1. Grasp the frame of the bike and the rear wheel, then point the needle into the appropriate hole in the frame until you hear a click. Pull the wheel towards you while holding the frame to make sure the wheel is properly installed and does not fall off the frame. Repeat the same operation for the other rear wheel (fig. 1).
2. Put the fender on the tube of the front wheel as shown in fig. 2. Make sure that the hole on the fender is on the left side.
3. Insert the front wheel tube into the hole on the front of the bicycle frame. Make sure the wheel is properly seated and there is no play. (fig no 3)
4. Insert the handlebar into the hole on the top of the bike frame, then tighten it with the screw and make sure it is securely fastened (fig. 4 and 5).
5. On the frame of the bicycle, put the saddle pad with the convex side down so that it adheres well to the frame (fig. 6).
6. Put a textile material on the seat, stretching it over the edges. Grasp the seat and unscrew the plastic knob on the bolt protruding from the seat. Put the seat on the washer so that the screw goes through the washer and the frame and its end protrudes from the bottom of the frame (fig. 7).
7. Tighten the screw with the plastic knob until you feel resistance and the seat is stationary (fig. 8).
8. In the appropriate holes on the outside on the back of the seat, insert one part of the securing rim until you hear a click, pay attention to the direction of the rim. Repeat the same operation with the other part of the securing ring. Pass one of the parts of the securing ring through the hole in the fabric. Put the two parts together until you hear a click (fig. 9 and 10).
9. Insert the backrest into the remaining holes at the back of the seat, make sure that it is properly attached and does not slide out (fig. 11).
10. Slide the hood over the tabs on the sides of the backrest (fig. 12).
11. Connect the two parts of the parent steering wheel. Insert it into the appropriate hole behind the seat until you hear a click. From the bottom of the bicycle frame, put the plastic cover on the lower part of the parental handlebar and tighten with the screw. Position the pad along the wheels (fig. 13 and 14).
12. Pass the steering rod through the hole in the front fender and the other end through the hole in the plastic cap with pt. 10., tighten with the screw (fig. 15 and 16).
13. Slide the rear basket onto the rear wheel frame (fig 17)

MAINTENANCE AND CLEANING

Visor: Do not wash. Do not bleach. Do not tumble dry. Do not iron. Do not dry clean. Clean with a clean, damp cloth and a mild soap. Allow to air dry. Do not submerge in water.
Seat cover, safety belts: Hand wash at max. 40 degrees C, do not bleach, tumble dry, do not iron, do not dry clean.
Frame: Clean the frame with a soft, clean, damp cloth and a mild soap.
STORAGE: Keep out of the reach of children

www.momi.store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>