Landskap Svämmä Outdoor Shower 40 Liters Black Instruction Manual
- June 10, 2024
- Landskap
Table of Contents
Landskap Svämmä Outdoor Shower 40 Liters Black
Product Information
The product is an outdoor shower that allows users to enjoy a refreshing shower in their garden or backyard. The product comes with a base plate, bottom tube, top and bottom parts, extension tubes, shower heads, hoses, and other necessary components for assembly. The product is designed to be connected to a garden hose and uses solar power to heat the water for the shower.
Components
The product comes with the following components:
- A base plate/bottom tube
- Top and bottom parts
- Extension tubes
- Shower heads
- Hoses
- Expander bolts and washers
- A drain plug
Assembly Instructions
- Mount the expander bolts in the holes and tap them slightly with a hammer to expand them. Place the base plate/bottom tube on top of the holes and secure them to the surface with the bolts and washers.
- Connect the top and bottom parts together by tightening the coupling clockwise by hand. Connect the hoses, making sure that the handle and shower head are in the same direction.
- Attach the shower head with the gasket to the extension tube, then attach the extension tube with gasket to the thread on the upper part of the outdoor shower by hand. Repeat for the second shower head.
- Attach the hose connection with the gasket to the bottom part of the shower and put the drain plug into the drain outlet.
- Open the shower handle and turn it to the hot position. Attach your garden hose to the hose connection and turn on the water to fill the outdoor shower. Close the shower handle once the water flows out of the shower head.
- Let the sun heat the water in the outdoor shower for about two to three hours, depending on available sunlight and outdoor temperature.
Copyright ©2021 Bygghemma Sverige AB. Original content rights reserved. All
product names, logos, and brands are property of their respective owners
Information contained within this document was considered accurate at the time
of publication but may be subject to revision
- Before installation, choose a sunny and wind-protected place
- Do not use the sun shower when there is a strong wind.
- Do not dispose with other household waste anywhere in the EU.
WHAT INBOX
- Spirit-level
- Measure tape
- Drill
- Wall drill bit
- Spanner
- Screw Driver
- Pen
PART LIST
OVERVIEW
INSTALLATION
-
Mark the placement of the mounting holes, and drill holes.
-
Mount expander bolts K in the holes. Place the expander bolt in the hole and TAP with a hammer to expand it slightly. Place the base plate/bottom tube B on top of the holes and secure them to the surface with the bolts and washers K supplied. The bottom plate will feel loose before it is fully tightened
The shower can also be installed on a heavy deck with beams or strong wooden trolley using suitable screws (not included). -
Connect the top A and bottom B parts, tighten the coupling clockwise by hand. Connect the hoses. Handle and shower head must be in the same direction.
-
Attach the shower head D with the gasket G to the extension tube E, then attach the extension tube with gasket F to the thread on the upper part of the outdoor shower by hand. Same action for shower head H attachen to bottom part R
Make sure that the top and bottom shower heads are facing downward, if not, turn them until it faces downward. -
Attach the hose connection J with the gasket I to the bottom part B, and put the drain plug L into the drain outlet.
FIRST USE OF THE OUTDOOR SHOWER
- Open the shower handle and turn it to the “hot” position. This ensures that no air pockets get stuck in the hoses when they are filled with water
- Attach your garden hose to the hose connection J. Turn on the water to fill the outdoor shower. It will take a few minutes to fill the outdoor shower.
- When the water flows out of the shower head D, close the shower handle. Now let the sun heat the water in the outdoor shower.
- Depending on available sunlight and outdoor temperature, it takes about two to three hours for the sun to heat the water in the outdoor shower.
- The water temperature in the outdoor shower can reach up to 60 ° C through strong sunshine.
Before using the shower, turn the shower handle to “cold” to avoid scalding. Then adjust to the desired temperature.
WINTER STORAGE
- Switch off and disconnect the garden hose
- Unscrew the cover and allow the water to drain out. NOTE if the back of your outdoor shower faces a facade, remember to protect the facade from the water with e.g. a disc.
- Open the shower handle and turn it to the “hot” position so that the water can drain out of the hoses and the outdoor shower (this takes about 8-10 minutes). Do not touch or turn the shower handle during emptying, otherwise the water will stop flowing out.
- When the outdoor shower is empty, replace the cover.
- Remove the upper part of the outdoor shower.
- Pour the remaining water out of the lower part of the outdoor shower.
- Clean with a little detergent and water and then dry all outdoor shower parts.
- Store all outdoor shower parts indoors and in a dry and heated place during the winter season to prevent frost damage.
Feature
- To avoid a plastic odour, let the water drain completely
- Max water pressure should be 3.5 bar, do not use an external pump
- After using the shower, wipe it with a soft cloth and gloves
- Never use salt or antifreeze in any capacity
- Heating causes water to expand, don’t leave it in the shower head
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>