Panasonic NI-WL30 Cordless Steam Iron Instruction Manual

Panasonic NI-WL30 Cordless Steam Iron

SAFE USE OF THE IRON

Your safety and the safety of others are very important We have provided important safety messages in this manual and on your appliance. Always read and obey all safety messages. The safety messages will tell you what the potential hazard is, how to avoid and reduce the chance of getting injuried, and what can happen if the instructions are not followed. Thank you for buying a Panasonic Iron
Your iron is an appliance to be used only for ironing fabrics on an ironing board.

IMPORTANT SAFETY INSTRUCTIONS

When using your iron, basic safety precautions should always be followed, including the following:

1. Independently use a household outlet, and do not use extension cord. Failure to do so may cause electric shock or fire .
2. Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the appliance. Failure to do so may cause fire, electric shock and burn.
3. Do not leave the iron unattended while it is connected to the mains.
4. To protect against any risk of electric shock, do not immerse the product in water or another liquid.
5. If the Power cord is damaged, it must be replaced by our authorized service agent to avoid a hazard. Do not apply the Power cord to other electrical appliances.
6. Do not allow the Power cord to touch hot surfaces of the iron. Allow the iron to cool completely before storing.
7. Burns can occur from touching hot metals parts, hot water, or steam. Use with caution when turning the steam iron upside down. Hot water may leak from the iron.
8. The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking. Do not repair by yourself. It should be repaired by the authorized service agent.
9. If you notice any smoke or fire coming out from the product, stop using immediately and unplug the unit from the mains to avoid fire or electric shock. Contact our authorised service agent to seek further assistance.
10. This iron must be used with the Power base. When the iron is not in use, always place the iron securely into the power base. Otherwise, it may cause the product to fall, fire, injury or burn.
11. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safely.
12. Children should be supervised to ensure that they do not play with the appliance.
13. Never modify, disassemble, or repair. Doing so may cause ignition or injury due to abnormal operation. Contact an authorised service agent for repair.
14. This iron must use the electrical outlet with earth connection. Fully insert the plug. Failure to do so may cause fire or electric shock.(For Hong Kong only)
15. Do not damage, modify, forcefully bend, pull or twist the Power cord. Also, do not place anything heavy on or pinch the Power cord. Doing so may cause electric shock or fire due to ashort circuit.
16. Unplug the Power plug to disconnected from outlet by grasping the Power plug, do not pull the Power cord.
17. Do not connect or disconnect the Power plug to a household outlet with a wet hand.
18. Do not use the appliance with a wet hand. Doing so may cause electric shock or fire due to a short circuit.
19. Do not use in proximity of flammable materials (such as benzine). Doing so may cause an explosion or fire.
20. Always unplug the appliance during filling, emptying, cleaning and not in using.
21. Do not insert pins or other foreign objects into the Soleplate. Doing so may  cause fire,electric shock or burn.
22. Regularly clean the Power plug to prevent dust from accumulating. Failure to do so may cause fire due to insulation failure caused by humidity. Disconnect the power plug and wipe with a dry cloth.
23. The Iron head must be firmly rested on the Power base, and the Power base must be placed on a flat and stable surface. When this product is used as a horizontal steam iron, the iron must be used on a stable surface. Otherwise, the Soleplate may be scratched, or even injuries or scald may be caused if the iron head falls over.

CAUTION- To reduce the risk of personal injury and damage to your iron:

1. Use the iron only for its intended purpose, for ironing fabrics on an ironing board. To protect against burns or injuries to persons, do not iron or steam fabrics that are being worn on the body.
2. Do not add perfume, vinegar, starch, descaling agents, ironing aids or other chemicals, they can stain fabrics; instead, use room temperature tap water for it.
3. Test on an inconspicuous area when using with high-end or specially processed items. Failure to do so may cause damage fabric.
4. Do not use the appliance with the exception of fabric (e.g.leather).Failure to do so may cause damage it.
5. Care should be taken when using the appliance due to the emission of steam.
6. If the Steam/Dry selector is not in the Dry position after using, remaining water will flow into the Soleplate result in burns in the next usage of the iron.
7. Do not use the Steam or Jet of Steam while the Power cord is unplugged. Water will remain inside the Soleplate which will cause staining. Do not use Steam or Jet of Steam while the Temperature Selector Button is set 0.
8. Do not store the appliance with the Power cord entangled. It may cause the Power cord damage, electric shock and fire.
9. Do not touch the hot surface. Doing so may cause burn.
10. Do not put the Soleplate too close to you or others since steam may unexpectedly erupt it, otherwise it may caused burn.
11. lf ironing wet clothing, it must be used as a Dry iron.*Failure to do so may caused water leak, burn.
12. Do not tilt, or diddle the iron. Doing so may cause burn due to water leak.
13. Do not use the iron in opposite. Doing so may cause burn due to water leak by wrong operation.

COMPONENTS IDENTIFICATION

HOW TO FILL WITH WATER

Make sure the iron is turned off and the AC Power Cord is unplugged from the electrical outlet. The iron can be filled with the Water Tank in place or removed. Confirm that the Steam/Dry Selector is moved to the Dry ironing position when installing or removing the Tank.

1. Remove the Water Tank by pressing the Release Button.

2. Open the Water Fill Cover.

3. Fill the Water Tank up to the” MAX” line.
   DO NOT OVERFILL. Check the water level with the Water Tank held in its vertical position.

4. Close the Water Fill Cover.

5. Re-install the Water Tank into the main unit. Push it until a click sound is heard.

HOW TO SUPPLY ELECTRICITY

The iron must be set securely on the Power Base in order to supply electricity. Electricity will only be provided while the iron is placed on the Power Base. If you desire to set the iron down while moving a garment on your ironing board, the iron must only be placed on the Power Base. The Power Base will keep the temperature of the iron at the selected level.

HOW TO USE AS A STEAM IRON

1. Fill the iron as described in ” HOW TO FILL WITH WATER”.
2. Set the iron on the power base securely and make sure the Temperature Select Button is set to “0 “.
3. Plug the AC Cord into the electrical outlet.
4. Set the Temperature Select Button to the” “or” “(steam) zone.
5. Preheat the iron until the indicator light goes out, usually about 1-2 minutes.
6. Hold the iron horizontally and move the Steam/Dry Selector into the steam position. Steam/Dry Selector is regulated as follows.
7. 7. Whenever the iron is positioned vertically, the steaming action will stop.

Note: Anti-Drip System will be activated when the temperature of the Soleplate’s surface drops. At the same time, the steam will stop. It is not a sign of malfunction when you hear a clicking sound. In this situation, you have to put your iron back onto the Power Base to reheat.

HOW TO USE AS A DRY IRON

1. Move the Steam/Dry Selector to the Dry position.
2. Position the iron vertically, set the Temperature Select Button to” 0 “.
3. Plug in the iron.
4. Set the Temperature Select Button to the desired position.
5. Preheat the iron until the Thermostat Operating Indicator Light goes out, usually about 1- 2 minutes.

SPECIAL FUNCTIONS

Jet of Steam

The “Jet of Steam” feature provides extra steam which goes deep into the garment and is helpful for removing stubborn wrinkles. The ” Jet of Steam “feature operates properly only in the “ ” indication area of the Temperature Select Button when steam or dry ironing ( If used at lower setting, water spotting will occur because the iron is not hot enough to change water to steam ). If you have not used the “Jet of Steam” feature for a long time, it is necessary to clean the inside of the iron before using this feature on any clothes to be ironed. Simply test the “Jet of Steam” feature several times away from the ironing board and clothes to be ironed. This will prevent brown spotting or water spotting on the clothes.

1. Fill the iron as described in” HOW TO FILL WITH WATER”.

2. Position the iron vertically and be sure the Temperature Select Button is set to “0 “.
   Plug the AC Power Cord into the electrical outlet.

3. Set the Temperature Select Button to the” ” indication area.

4. Preheat the iron until the indicator light goes out, usually about 1-2 minutes.

5. Simply pump the “Jet of Steam Button ” when steam is desired. Pump the ” Jet of Steam Button ” several times at the beginning of each ironing session.

6. Allow at least 2-5 seconds between uses of the ” Jet of Steam Button ” to prevent water spotting. Use a press colth if necessary.

CAUTION

Do not use the” Jet of Steam Button” until the Thermostat Operating Indicator Light turns off after setting the Temperature Select Button to “ ” . Hot water may leak from the Soleplate and burns may result, and it may cause corrosion.

Vertical Steam

To get better results when using vertical steam, hang the garment on a clothes hanger. Curtains and drapes may also be steamed once they’re hung. Hold the iron away from your body, close to but not touching the fabric. Pull the fabric tight with your free hand and pump the Vertical Steam Button (Jet of Steam Button) at 5 seconds intervals as you pass the iron over the wrinkled fabric.

WARNING
Never iron clothes on the body or point your iron at anyone when steaming. Keep hands and body away from steam areas while using vertical steam feature.

Anti-Drip System ( Automatic Water Seal)

This model has an Anti-Drip System. When the temperature of the Soleplate’s surface drops below 25Q° F(121 °C), the valve for the vaporizing chamber in the iron automatically closes and stops the water from going in further. This prevents hot unvaporized water from spitting out from the soleplate when the iron has cooled down. With this system, it is unnecessary for you to wait till the inside of the vaporizing chamber dries completely when you store the iron.

NOTE:
It is not a sign of malfunction when you hear a clicking sound. This sound can be heard whenever this system is activated.

Stay Clean Vents

The built-in Anti Calcium System in the Tank continuously reduces scale buildup in the vaporizing chamber of the iron. This system makes it possible to use the steam function for a long period of time and prevents steam vents from clogging.

HOW TO CARE FOR YOUR IRON

AFTER EACH USE

1. Set the Temperature Select Button to” 0 “.
2. Turn the iron off and unplug.
3. Empty the iron immediately after using. Do not store the iron with water in it.
4. Move the Steam/Dry Selector into the Dry position. If the Steam/Dry Selector is not in the Dry position after using, remaining water will move into the Soleplate and damage the Soleplate and may result in burns during the next initial use of the iron.
5. Wait till the iron has cooled before storing it, and always set it on the heel rest to protect the Soleplate from scratches, corrosion or stains.

MAIN BODY

1. When cleaning the main body of the iron , make sure that iron has cooled down.
2. Wipe the iron with a damp cloth If necessary, use a mild detergent. NEVER USE ANY HARSH CLEANERS.

SOLE PLATE

• Starch and other residues can be easily removed from the Soleplate with a damp cloth.
• To avoid scratching the Soleplate, never use a metallic pad to clean the Soleplate, and never place the iron on a rough surface.
• If synthetics are being ironed on a higher temperature level than instructed, not only will the fabric be ruined, but the Soleplate will often be covered with the melted remains of the synthetic fabric.
• The best way to remove synthetic residue from the Soleplate is to iron over an old cotton rag after heating the iron.

CAUTION
Never use steam iron cleaners in the iron since it may cause damage to the inside of the iron. If the Power Cord is damaged, it must only be replaced by a special cord.
The iron must only be used with the Power Base provided.

SPECIFICATIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>