TENTANDTABLE COM S154 Commercial Inflatable Water Slide Instruction Manual

: July 5, 2024
: TENTANDTABLE COM

Table of Contents

TENTANDTABLE COM S154 Commercial Inflatable Water Slide
Product Usage Instructions
OVERVIEW
SET-UP
OPERATING INSTRUCTIONS
Bladder Use and Replacement Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TENTANDTABLE COM S154 Commercial Inflatable Water Slide

Product Information

Specifications

Product Name: 34 FT. Slide/ Slip-and-Splash
Type: Inflatable Amusement Device
Required Blower: Commercial Inflatable Blower 1.5 HP, minimum 700 cfm @ 4.5
Operator Requirement: 2 trained operators/attendants at all times
Ground Cover Tarps: Required for setup
Anchor Straps: Must be secured with recommended stakes
Electric Requirement: GFCI extension recommended for safety

Product Usage Instructions

Setup:

Safety Check List: Ensure the area is flat, level, and free of obstacles. Do not attempt to move the inflatable alone.
Site Assessment: Lay down a ground cover tarp on a flat surface.
Unroll and Positioning: Roll the inflatable onto the tarp with the inflation tubes at the back.
Inflation Tubes: Fold and secure the unused inflation tube properly.
Proper Staking: Slide stakes through D-rings and ensure anchor straps are fully extended and secured.

Operating Instructions:

Slide Properly: Slide feet first, arms crossed, feet together. No head-first sliding.
Maintain Inflation: Keep the blower on continuously during use.
Safety Guidelines: No chewing gum, cell phones, or loose objects. Keep a 5-foot safety area around the device.
No Climbing: Do not hang or climb on the outside walls.
Weather Monitoring: Check weather conditions regularly. Do not use the device in high winds, rain, snow, or lightning.

Deflation and Folding:
Prior to deflation, remove all accessories and debris from the game surface. Follow proper folding instructions as per the manual.

Frequently Asked Questions (FAQ):

Q: How many operators are required for supervision?
A: Two trained operators/attendants are required to supervise the device at all times.
Q: What electric requirement is recommended for safety?
A: A GFCI extension is recommended to reduce the possibility of shock.
Q: What should be done in case of high winds or inclement weather?
A: Monitor weather conditions regularly and do not use the device in high winds (15mph+), rain, snow, or lightning. Evacuate the unit immediately in case of lightning and unplug the power.

OVERVIEW

SET-UP

STEP 1.
- WARNING: Inflatables are very heavy —do not attempt to roll or move these games by yourself
- Do not inflate in high winds or rain— High winds are considered to be 15 mph or higher
- Inspect the site, look for overhead and underground obstructions— such as utilities
- Call your local utility to have utility lines marked (call 3–5 days ahead)— call811.com is a good resource— ‘click’ 811 in Your State
- Use an adequate three wire extension cord, min. 12 gauge for 50ft. maximum length—never cut or remove the round grounding pin from the cord
- Always connect a GFCI extension cord adapter to any extension cord before plugging into a power source— this reduces the possibility of shock in wet environments
- Check the GFCI operation at least once per event
- Before staking unit into the ground, obtain marking and location information from the utility companies if there is a possibility of striking underground utilities
- Remove all occupants if wind becomes excessive—deflate unit, if wind continues
- Important, the operator/attendant is responsible for the safety of those using the inflatable amusement device
STEP 2.
- Pick a location free from overhead utility lines, trees, roads, sidewalks, bodies of water and cliffs—or any hazard
- Any nearby obstruction should be at least 20 feet away from inflatable
- Spread tarps (sold separately) on the slide/bounce house location, to protect unit
- Locate the blower and power cord in an area that is not in a direct walkway—be sure the blower is on a flat and dry surface
- A minimum of 2 installers recommended Recommended Tools and Equipment: sledge hammer, ground tarp, hand truck or 4 wheel dolly, crowbar/stake remover safety goggles, GFCI extension adapter, 50´ 12AWG extension cord
STEP 3.
- Carefully place unit, using dolly, at one end of tarp—it’s easier to move at this stage!
- See (drawing), find back end of inflatable device and roll onto tarp
- (Make a mental note or snap a picture of how the inflatable is folded and positioned as you unroll the game. This will be beneficial when you re-roll the device later)
- Check location, make any adjustments before inflation—unfold device completely
- Start the staking process— place stakes through the inflatable anchor straps, all around the inflatable amusement device—see (pg. 3) for proper staking
STEP 4.
- Plug the blower power cord into the GFCI extension, then plug the GFCI extension into the extension cord—connect the fan cone to the inflation tube
- Close off the unused inflation tube(s)
- Plug the extension cord into the power source
- Check the inflation tube to make sure it is properly attached to the blower fan —the inflation tube must be properly closed around the blower outlet chute for maximum inflation during use
- Close all zipper vents (if applicable)
  Note: AIR ESCAPING FROM SEAMS is normal, during the operation of the unit— it keeps the unit inflated, but not overfilled (air should be escaping during use)
STEP 5.
- Locate the on/off switch (if applicable) on the blower and turn it on—observe the inflation of the inflatable as it rises
- When inflation is almost finished, check the positioning of the stakes—hammer them all the way in— see (step 5)
- Note: For medium soil conditions, larger stakes will increase pullout capacity*
- When properly inflated, all inflated areas of the game will become pressurized and firm
- Once inflated, check for any rips, holes, or damage—‘walk-around during use
- Important: Keep the blower on, continuously, for the duration of your event— to maintain proper inflation

OPERATING INSTRUCTIONS

The following instructions must be read and adhered to by all operators/attendants regarding this inflatable device:

Trained attendants should be positioned at the entrance and exit of the device
Attendants must be at least 18 years old
Trained operators/attendants should assist the movement of all child patrons as they enter and exit the amusement device
Attendants should remove all debris from the inflatable before allowing persons to enter or climb on the inflatable
Trained attendants should only allow persons of the same size and age on the inflatable device at the same time— (check capacity on device warning label)
People with medical conditions or severe disabilities should not use this Inflatable amusement device
Attendants should make sure that no one enters the inflatable device with shoes on, eyeglasses or sharp objects in their hair or on clothing
Attendants should observe patrons at all times while they are in the inflatable
Attendants should be close enough to be able to warn against flips, piling on, wrestling, bouncing against the side, grabbing the net or bouncing too close to each other—attendant should ask anyone doing these things, after being warned, to leave the inflatable device immediately
Whistle use required for attendants
No running to enter the inflatable device The attendant should point out and make customers aware of the posted warning sign on the front or side of the inflatable
Attendants should watch for any signs of deflation such as sagging, wrinkling or distortion—if observed, the attendant should ask the people in the inflatable to evacuate, calmly and safely
Attendants should keep all spectators outside the inflatable amusement device and at least 5 feet away from the sides
The starting line is 48 inches from the entry of the inflatable amusement device
Prohibit excessive rough play by occupants—blow whistle
In times of excessive heat monitor the heat inside the play area and slide surface
Do not allow any individual in the rear of the game or near the electric blower at any time
Deny entry if any patron poses a risk to others— or, if they consumed alcohol or illicit drugs
15mph wind equals; dust and loose paper rising and movement of small branches —Hazardous winds; small trees sway and large branches are in motion
Check the blower/inflation tube regularly to ensure there isn’t any excessive leakage
Check stakes regularly
Keep airborne trash/leaves clear of blower intake

DEFLATION AND FOLDING

Before deflating; Inspect for any damage and repair as necessary
Clean inflatable amusement device(s) and dry, after use—by running air through it
Unplug the blower at the power source
Loosen first inflation/deflation tube strap and remove tube from the blower cone —make sure the tube is pulled away from the inflatable and is straight
Loosen second inflation/deflation tube strap and pull the tube away from the inflatable
Open all deflation flaps
While the inflatable amusement device is deflating, remove stakes, put blower fan away, and store extension cord(s)
Two people, minimum, needed to fold
Guide inflatable inward and to the front —while the air is being released
Begin folding inflatable amusement device—pull vertical peaks/shapes toward the front, to flatten and release more air
Next, situate top of unit over the bottom, pancake style—and fold peaks into the middle, see (drawing)
Once you make the folds, you will notice that air is still inside the game—start at the front and walk, in stocking feet, to the back—removing most of the air
Work the air out towards the back of the unit through the inflation tube(s)
Commercial inflatables take 5–15 minutes to completely deflate

CLEANING THE INFLATABLE

Do not use M.E.K.(methyl ethyl ketone) to try and clean your inflatable, as this will damage the vinyl
Do not use a chlorine based cleaner or bleach, as this may damage the threads
Do not use any cleaning products containing alcohol to try and clean your inflatable device, as this will damage any printing that may be on your inflatable
Use water and/or mild cleaner sparingly by sponging
Excessive water or cleaner may penetrate the seams and collect inside of the tubes —also, bubbling from the seams during operation may occur

FINAL FOLD AND ROLL

Fold both sides into the center of the inflatable—each person should place one foot on the inflatable at the fold line
Fold at the same time—walk down the game and straighten out the seam
Repeat this procedure for the other half of the game
The roll; make sure that at least one of the inflation tubes is extending—as you roll the unit up, air will escape and the inflatable device will roll much better
Important: Twist the beginning of the ‘roll’ very tight
Start your roll from the FRONT (opposite the inflation tube)
As you progress, be sure that the roll is straight and tight

SLIP KNOT (for rolled inflatable)

Near the end, allow time for the last bit of air to escape
Locate tie strap—pull to top of roll
We recommend you tie a tight slip knot around the roll
Stand the inflatable amusement device on end—place the transport/storage bag over one end of the game and work it down as far as you can

STORAGE BAG

It is important that you work the bag down to the top of the roll—flip the unit and pull the bag up over the top of the inflatable amusement device
Tie the bag closed
Lay the game onto a dolly and roll it to your designated storage area
WARNING: Inflatables are very heavy. Do not attempt to roll or move these games by yourself. When lifting any type of heavy weight, be sure to lift with your legs and not your back. If in doubt about your ability to move something, get help.

Bladder Use and Replacement Instructions

Inflatable and Combo Devices with slides use a BLADDER system to keep the slide wet. They are included with every new inflatable device.

BLADDER SYSTEM

Just before inflation, connect the bladder system
Most water slides have water bladder systems built into the unit—it keeps the slide wet
Start by taking your garden hose through the hose loops (side of inflatable)— begin at lowest loop
Then, locate bladder opening and attach hose
After the unit is fully inflated and you’re ready for use, turn on water supply— leave it running for the duration
Note: The landing will catch the water that runs from the slide—do not add water to the landing

WATER LEVEL

Water level should be next to nothing– if the level increases over one inch, it is recommended to drain out some of the water, from landing
Drainage holes are located under the slide-flaps, that extend over the side of the inflatable device
BLADDER REPLACEMENT
If a new bladder is needed, it should be attached to the original bladder
Zip-tie new bladder to the vinyl strip, at the edge of original bladder, through grommet holes— make sure water holes point downward

DIRECTIONS FOR USE:
(operator/attendants should be assisting patrons as they enter and exit the inflatable amusement device)

Communicate to all patrons– safety, using the inflatable amusement device, usage and dress code rules
Carefully enter inflatable amusement device at the entrance and climb the incline slowly
Careful not to collide into other patrons, be respectful of others safety at all times
When patrons are ready to slide, do so in a seated position, one at a time, with proper form (patrons may exit carefully out the entrance tunnel, if they do not wish to slide)
Exit the device, after sliding, as careful as possible—no jumping off the edge of the device
As one patron exits, allow another to enter— remember to maintain the correct device capacity (total number of patrons allowed, at one time)

EVACUATION PLAN:
In the case of rapid deflation or poor weather during operation, attendants should follow these steps–

Operator/attendants should blow whistles to evacuate patrons immediately and safely— aid child patrons as they exit, then tell them to step away from inflatable device
Any patrons on elevated platforms should climb down the stairs, backwards—if a patron is sitting ready to slide, let that one slide down, only (for units with slides)
Deflate inflatable amusement device if necessary (high wind)—re-inflate when safe
Call medical responders if anyone is injured

DAILY CHECKLIST:

Check wind conditions at beginning of day and throughout the day.
Ensure temperatures are greater than 40ºF.
Recheck the minimum 12 gauge- 3 wire extension cord and the CFCI (ground fault circuit interrupter).
Ensure there are no obstructions in the blower.
Ensure unit is properly inflated.
Ensure all tether points are secure.
Ensure all deflation zippers and flaps are closed.
Walk around the unit and inspect seams and search for wear damage.

MAINTENANCE and INSPECTION

Determine a cleaning and preventative maintenance schedule to keep this device function properly
The device can be easily cleaned with a cloth or light brush. Use a vinyl cleaner and rinse lightly, to remove detergent before storing.
DO NOT PACK THE INFLATABLE DEVICE WHEN WET. If it wasn’t dried properly, lay the unit out to dry at the earliest opportunity.
The unit should be inspected regularly for damage. If there is evidence of tearing at the anchor points or vinyl panels, the inflatable amusement device should not be used until the repair has been completed.

REPAIRS

Repairs made by anyone other than the original manufacturer, shall be made using the same construction method—with comparable materials—unless manufacturer agrees otherwise.
To repair small tears up to 12″ use “Single Patch Method” as follows.
Cut an oval or round vinyl patch approximately 4″ larger than the cut.
Clean the area around the tear.
Apply SX-69 vinyl glue on the patch and on the surface of the inflatable device.
Allow the manufacture´s recommended drying time before applying the patch to the inflatable device as indicated on the label on the container.
Place the patch covering the cut area and apply pressure for 1 minute. Refer to the glue manufacturer ´s label for the recommended time for glue to dry once the patch is applied.
If the “Single Patch Method” is not a viable option use PatchALL* for a non-glue repair until you can apply the “Single Patch Method” or send the unit to a repair facility.

DAILY CHECKLIST

Ensure maximum winds are less than the manufacturer´s recommended wind speed requirement for unit.
Ensure temperatures are greater than 40° F.
Ensure that a minimum 12 gauge 3 wire extension cord is used with the blower and is connected to a CFCI (Ground Fault Circuit Interrupter).
Ensure there are no obstructions in the blower(s), blower intake and the unit´s inflation tubes.
Inspect the blower inflation tubes, they should be in good condition and firmly fixed to blower.
Ensure unit is properly inflated—with the blower pointing straight at device.
Visually inspect device for any holes or rips in the fabric or seams.
For inflatable amusement devices with multiple units, check all connection points.
Ensure all tether and anchor points are secure. Check stakes.
Ensure all deflation zippers and flaps are closed.
Walk around the unit and inspect seams and search for wear damage.
PatchALL are clear polyurethane patches or tape. They are quick, flexible, long lasting, airtight and waterproof—with no gluing.
Visit TentAndTable.com for all your Inflatable Accessories including; blowers, impact mats, dollies, heavy-duty hand trucks and repair kits.

MODIFICATIONS: This inflatable amusement device shall not be altered in any way that constitutes a major modification without written from the device manufacturer.

WARNING: As with any Amusement Device, there is an inherent risk of personal injury.
As such, ALL PERSONS play at their OWN RISK and peril!

If unit begins to deflate EXIT immediately!
DO NOT Operate this unit if WINDS exceed 15 M.P.H.
DO NOT Inflate or use this inflatable without first SECURING to ground. Use stakes at all tethering and anchor points.
DO NOT Pound stakes into ground without first VERIFYING gas, water & electrical locations with local UTILITY COMPANIES!
DO NOT Use silly string on unit.

SHOCK HAZARD!
DO NOT Use this equipment on DAMP surfaces or during inclement weather.
THIS UNIT REQUIRES A CONSTANT SOURCE OF 110V-20amp POWER PER BLOWER SYSTEM.

DO NOT ENTER RIDE – UNLESS ATTENDANTS ARE PRESENT!

A MINIMUM OF TRAINED OPERATOR(S) MUST BE ON DUTY AT ALL TIMES!

AIR LEAKING OR BUBBLES FROM SEWN SEAMS ARE NORMAL DURING OPERATION OF THIS INFLATABLE

CHECK ALL SPECIFICATIONS LOCATED ON SAFETY LABEL– ATTACHED TO YOUR UNIT.