GeoVision 125-SD4834-IR GV-IP Speed Dome Camera Owner’s Manual

June 10, 2024
GeoVision

Quick Start Guide
GV-IP Speed Dome
GV-SD2322-IR
GV-SD2722-IR
GV-SD3732-IR
GV-SD4825-IR
GV-SD4834-IR
ISD2722IR-QG-C

125-SD4834-IR GV-IP Speed Dome Camera

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

© 2021 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein. Features and specifications are subject to change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV series products are trademarks of GeoVision, Inc. Windows is the registered trademark of Microsoft Corporation.

November 2021
Scan the following QR codes for product warranty and technical support policy:

[Warranty] [Technical Support Policy]
![GeoVision 125 SD4834 IR GV IP Speed Dome Camera -

qr1](https://manuals.plus/wp-content/uploads/2023/04/GeoVision-125-SD4834-IR- GV-IP-Speed-Dome-Camera-qr1.png)
https://www.geovision.com.tw/warranty.php| https://www.geovision.com.tw/_upload/doc/Technical_Support_Policy.pdf

Note for Connecting to GV-VMS / DVR / NVR

The GV-IP Speed Dome is designed to work with GV-VMS / DVR / NVR, a video management system. Note the following when the camera is connected to GV-VMS / DVR / NVR: Once the camera is connected to the GV-VMS / DVR / NVR, the resolution set on the GV-VMS / DVR / NVR will override the resolution set on the camera’s Web interface. You can only change the resolution settings through the Web interface when the connection to the GV-VMS / DVR / NVR is interrupted.

Note for Recording

Mind the following when using a memory card for recording:

  • Recorded data on the memory card can be damaged or lost if the data are accessed while the camera is under physical shock, power interruption, memory card detachment or when the memory card reaches the end of its lifespan. No guarantee is provided for such causes.
  • The stored data can be lost if the memory card is not accessed for a long period of time. Back up your data periodically if you seldom access the memory card.
  • Memory cards are expendable and their durability varies according to the conditions of the installed site and how they are used. Back up your data regularly and replace the memory card annually.
  • To avoid power outage, it is highly recommended to apply a battery backup (UPS).
  • For better performance, it is highly recommended to use Micro SD card of MLC NAND flash, Class 10.
  • Replace the memory card when its read/write speed is lower than 6 MB/s or when the memory card is frequently undetected by the camera.

Note for Installing Camera Outdoor

When installing the camera outdoor, be sure that:

  1. The camera is set up above the junction box to prevent water from entering the camera along the cables.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - entering the camera
  2. Any power, audio and I/O cables are waterproofed using waterproof silicon rubber or the like.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - waterproof silicon 
  3. The screws are tightened and the cover is in place after opening the camera cover.

Introduction

Welcome to the GV-IP Speed Dome Quick Start Guide. In the following sections, you will learn the basic installations and configurations. For a detailed user manual, see the GV-IP Speed Dome User’s Manual on the company website.

Packing List
  • IR IP Speed Dome

  • M4 Hex Key

  • Waterproof Guidelines

  • Download Guide

  • 24V AC Power Adapter (only for GV-SD2322-IR / SD2722-IR / SD3732-IR)

  • Waterproof Rubber SetGeoVision 125 SD4834 IR GV IP Speed Dome Camera - Rubber Set

Optional Accessories

Optional devices can expand the capabilities and versatility of your camera. Contact your dealer for more information.

Name Details
GV-Mount Accessories The GV-Mount Accessories provide a comprehensive lineup

of accessories for installation on ceiling, wall and pole. For
details, see GV-Mount Accessories Installation Guide.

Overview

GeoVision 125 SD4834 IR GV IP Speed Dome Camera -
Overview

No. Name Function
1. **** Default Button Resets all configurations to default factory

settings. See 7. Restoring to Factory Default.
2.| Micro SD Card Slot| Inserts a micro SD card to store recording data.

Installation

You can separately purchase optional mounting accessories to mount your GV-IP Speed Dome on a wall, ceiling or pole. Make sure the wall is strong enough to support the  camera and the mount. For details, see GV-Mount Accessories Installation Guide.

Required Items

  • GV-Mount210 (purchased required)
  • Wall screws x 4 (user-prepared)

Note: GV-SD2722-IR / SD3732-IR / SD4825-IR / SD4834-IR supports a series of Intelligent functions, which work best when the installation abides by specific requirements. See 4.6.1 Note for Face Detection, and Note for People Counting, and Smart Settings in Chapter 4, GV-IP Speed Dome User’s Manual for details.

  1. Unscrew the back cover of the camera.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - cover of the camera
  2. Insert the micro SD card into the slot, and secure the back cover of the camera.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - back cover Note: Be sure to format the memory card on the camera’s Web interface (Setup > Storage > Storage).
  3. Place the pendant tube on the wall, and mark the position of the screw holes.
  4. Drill holes on the wall, and secure the pendant tube to the wall with 4 self-prepared screws.
  5. Attach the safety lock of the camera to the pendant tube.
  6. Thread the data cable through the pendant tube.
  7. Attach the camera to the pendant tube, rotate the camera until it is locked into position, and secure the indicated screws.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - locked into position
  8. Insert the pendant mount screws and tighten with the supplied M4 hex key.
  9. Thread the Ethernet cable through the waterproof rubber set as shown below.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - waterproof rubbe

Note: The size of RJ-45 connector must be within 14 mm to go through the waterproof rubber set.

Connecting the Camera

The camera comes with a data cable that allows you to connect the camera to the power adapter, microphone, speaker, and I/O devices.

GeoVision 125 SD4834 IR GV IP Speed Dome Camera - camera to the
power

  1. Connect the supplied power adapter to the 3-pin terminal block, or connect the Ethernet cable to the PoE port. Either of the red or black cables can be used for anode (+) and the cathode (-).GeoVision 125 SD4834 IR GV IP Speed Dome Camera - Power Adaptor 
  2. Connect a standard network cable to the Ethernet cable of the camera.
  3. Optionally connect the TV-out (BNC) cable to a monitor. The TV-out function can be used during installation to adjust the camera image.
  4. Optionally connect I/O devices, speaker and microphone to the camera. You can connect
    up to 2 alarm inputs and 1 output device. See the Wire Definition section below.
    Each time the camera is powered on, it will perform a self-test to check the Pan/Tilt/Zoom (PTZ) function. After the self-test, you can operate the camera.

Note: If you are using your own power adapter, you may need to ground the camera using
the yellow cable (GND) on the 3-pin terminal block.

Wire Definition
GV-SD2322-IR / SD2722-IR / SD3732-IR

No. Wire Definition
1 Brown Audio In
2 Brown / White GND
3 Green Audio Out
4 Green / White GND
5 Gray Alarm In 1
6 Purple Alarm In 2
7 Black GND
8 Orange Alarm In –
9 Orange / White Alarm Out +
10 Yellow RS-485 – (GV-SD2722-IR / SD3732-IR)
11 Yellow / Black RS-485 + (GV-SD2722-IR / SD3732-IR)

GV-SD4825-IR / SD4834-IR

No. Wire Definition
1 Brown Audio In
2 Green Audio Out
3 Green / White GND (GV-SD4825-IR)
4 Brown / White GND (GV-SD4834-IR)
5 Gray Alarm In 1
6 Purple Alarm In 2
7 Black GND
8 Orange Alarm Out –
9 Orange / White Alarm Out +
10 Yellow RS-485 –
--- --- ---
11 Yellow / Black RS-485 +
12 Yellow & Green GND (GV-SD4834-IR)
13 Black AC 24V / DC 24V- (GV-SD4834-IR)
14 Red AC 24V / DC 24V+ (GV-SD4834-IR)

Accessing the Camera

4.1 System Requirements
Once installed, your camera is accessible over the network. Make sure your PC has good network connection, and meet the following requirement:

CPU Intel Core i5-4670, 3.40 GHz
Memory DDR3 8 GB RAM
On Board Graphics Intel HD Graphics 4600 (Versions of driver from year 2014

or later
required)
Web Browsers|

  • Internet Explorer 11.0 or above
  • Google Chrome
  • Mozilla Firefox
  • Safari

Note:

  1. Some functions are not available on non-IE browsers; e.g. Local Settings (see 4.1.2 Local Settings in the User’s Manual) is not supported by Google Chrome.
  2. Only H.264 codec is supported for live view on non-IE browsers.
Looking Up the Dynamic IP Address

By default, when the camera is connected to LAN with a DHCP server, it is automatically assigned with a dynamic IP address. Follow the steps below to look up its IP address.

Note:

  1. The computer you use to configure the IP address must be under the same LAN with your camera.

  2. Multilingual Web interface is only supported by GV-SD2722-IR / SD3732-IR.

  3. By default, the Administrator’s username is admin and cannot be modified.

  4. Download and install the GV-IP Device Utility program from the company website

  5. On the GV-IP Utility window, click the button to search for the IP devices connected in the same LAN. Click the Name or Mac Address column to sort.

  6. Find the camera with its Mac Address, click on its IP address.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - Mac Address

  7. For the first-time users, you will be requested to set up a password.

  8. Type a new password and click OK.

  9. Type your username and password on the login page and click Login.

Configuring the IP Address

If the camera is connected to LAN without a DHCP server, the default IP address will be 192.168.0.10. Follow the steps below to modify the IP address to avoid IP conflict with other GV-IP devices on the same LAN.

  1. Open your web browser, and type the default IP address 192.168.0.10.
  2. Type your username and password. Click Login.
  3. Click Setup, select Common in the left menu and select Network.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - select Common 
  4. Select Static IP from the IP Obtain Mode drop-down list.
  5.  Enter the IP address, subnet mask, and default gateway address. Make sure that the IP address of the camera is unique in the network.
  6. Click Save.

The Web Interface

Once you log in the Web interface, you will see the live view as shown below.

For GV-SD2322-IR

GeoVision 125 SD4834 IR GV IP Speed Dome Camera - shown
below

No. Name Function
1 Proportional Set the display ratio of the image.

· Scale: display images by 16:9.
· Stretch: display images by window size.
· Original: display images in its original size.
2| Live Stream| Select a live video stream: main stream, sub stream or third stream.
3| Image| Open the image setting page.
4| Full Screen Mode| Display in full screen mode.
5| Play/Stop| Play or stop live video.
6| Volume| Adjust the audio output volume on the PC.
---|---|---
7| Microphone| Adjust the microphone volume on the PC during audio communication between the PC and the camera.
8| Snapshot| Take a snapshot of the current image displayed on the PC.
9| Local Recording| Start or stop local recording.


10

| Audio Communication| Start or stop audio communication between the PC and the camera.
11| Digital Zoom| Start or stop digital zoom.
12| 3D Positioning| Start or stop 3D positioning (optical zoom).
13| PTZ control panel| Show or hide the PTZ control panel. — See 5.1 PTZ Control Panel.
14| | Reset the packet loss rate to zero.
15|
| Display packet loss rate and bit rate information in the bottom.
Note:
1. The paths for saving snapshots and local recordings are set in System Configuration.
2. The buttons (No. 14 and No. 15) will appear on the floating toolbar after you move the mouse cursor on a live view window.

For GV-SD2722-IR / SD3732-IR

GeoVision 125 SD4834 IR GV IP Speed Dome Camera -
fig13

No. Name Function
1 Image Open the image setting page.  — See 4.5.1 Image in the User’s

Manual.
2| Two-way Audio| Start or stop  two-way audio.
3| Area Focus| Start or stop  area focus.
By activating this function, you can set the camera focus based on a defined area of the live view. To activate Area Focus, follow the steps below:
Step 1: Click  on the toolbar.
Step 2: Click and drag on the live view to specify an area. The focus of the live view changes to the specified area.
4| Face Snapshot (only applicable to GV-SD4825-IR /SD4834-IR)| Start or stop face snapshot.
By activating this function, the camera takes face snapshots, and displays them on the right of the live view window. Before activating this function, you must enable Face Detection – See
4.6.7 Face Detection in the User’s Manual. To display face attributes detected, define Attribute Collection and enable Display Attributes beforehand – See 4.1.2 Local Setting and 4.6.10 Attribute Collection in the User’s Manual.
5| Full Screen Mode| Display in full screen mode.

PTZ Control Panel

You can find the PTZ control panel to the right of the live view.

GeoVision 125 SD4834 IR GV IP Speed Dome Camera - PTZ Control
Panel

No. Item Function
1 Auto Pan Start or stop auto panning of the camera.
2 PTZ Control Panel Control the direction of the camera and release the

control.
3| PTZ Speed| Adjust the moving speed of the PTZ camera.
4| Zoom| Adjust the camera’s zoom (optical).
5| Focus| Adjust the camera’s focus.

6

|

Snow

| Turn on or off the snow control. When enabled, the camera will rotate to remove accumulated snow if detected by the camera.
7| Screen Lock| Lock or unlock the camera direction.

8

|

Preset

| Select a preset and the camera goes to the selected preset.
— See the Adding a Preset Point section below.

9

|

Patrol

| Select a patrol route. – See the Adding a Patrol Route section below.

Adding a Preset Point

  1. Once Preset is selected in the control panel, adjust the dome view to the desired direction, zoom and focus.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - Preset Point2. Click the Add button  to add it as a preset.
    3. Enter a number and name for the preset and click OK.

Adding a Patrol Route

  1. On the control panel, click the Add button to add a patrol route.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - patrol route
  2. On the Add Patrol page, type the desired route ID and name.
  3. Click Add to add a patrol action. Use the buttons to adjust the sequence of the actions and click OK.

Note:

  1. It is recommended that the first action type is Go to Preset.
  2. If Keep Rotating is selected, the camera will rotate at the set speed in the set direction or Position for a certain amount of time.
  3. For more details on other available PTZ movement settings, see Chapter 3 PTZ Control Panel, GV-IP Speed Dome User’s Manual.

Upgrading System Firmware

GeoVision periodically releases the updated firmware on the website. To load the new firmware into the camera, follow the instructions below.

  1. At the top of the Web interface, click Setup.
  2. In the left menu, select System and select Maintenance. This page appears.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - System and selec
  3. Click the Browse button to locate the firmware file (.zip) saved at your local computer.
  4. Optionally select Upgrade Boot Program to reboot the camera after a successful upgrade.
  5. Click the Upgrade button to process the upgrade.

Restoring to Factory Default

If for any reason the camera is not responding correctly, you can restore the camera back to its factory default settings using the Web interface or the Default Button.

Using the Web Interface

To restore to default settings using the Web interface:

  1. At the top, click Setup.
  2. In the left menu, select System and select Maintenance.
  3. Under the Config Management section, click the Default button.

GeoVision 125 SD4834 IR GV IP Speed Dome Camera - Config
Management

Directly on the Camera
  1. Unscrew the back cover of the camera.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - cover of the camer
  2. Press and hold the default button for about 30 seconds.GeoVision 125 SD4834 IR GV IP Speed Dome Camera - default button
  3. When the camera rotates twice, the process of loading default is completed and the camera robots automatically.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals