ADJ AHS07 Box Per SSD Pcie User Manual

ADJ AHS07 Box Per SSD Pcie

Product Information

• Code: 120-00028
• Manufacturer: ADJ
• Country of manufacture: China
• Distributor: IoT Tecnologie s.r.l., Italy

Features:

• SSD M.2 drive for external storage
• PCIe connector on corresponding PCBA
• USB-C interface for connection to computer
• Compatible with Windows operating system

Usage Instructions

System Requirements:

• Windows operating system

Packing Contents:

• SSD M.2 drive
• External enclosure
• USB-C cable

Installation:

1. Push with finger as shown in the location and direction of picture to open the lower cover of the external enclosure.
2. Insert the SSD PCIe into the connector on the corresponding PCBA. Fasten with pressing parts.
3. Close the bottom cover, pushing as shown in the direction of picture.

Connection to Computer:

1. Connect one end (Type C) of the USB cable into the USB Port of your SSD external enclosure.
2. Connect the other end of the USB-C cable into any active USB-C port of the computer.
3. Let Windows search and install the driver automatically.
4. Open My Computer to see your external hard drive ready to use.

Partitioning the SSD External Disk:

1. Click on [Gestione disco] in the left part of the window, and all connected disks will be listed on the right.
2. Find the newly added disk with its status on the right-hand side. Create or delete a new partition by right-clicking in this area.
3. Follow the instructions of the Guide to partition and format your SSD.
4. Wait until the Guide finishes formatting your disk. Your disk should now appear in [This PC], ready to use.

FAQ:

• For extensive service, visit the website: www.adj.it
• Do not open or repair this device.
• Do not use the device in a damp environment.
• Clean the device with a dry cloth.
• Please use the product only for the purpose for which it was designed. It is forbidden any other use or modification.

Warranty:

• This product is guaranteed against any manufacturing defect,
  based on the D.Lgs. February 2, 2002, No 24.

• In case of failure, please contact the retailer where you purchased it. Please check www.adj.it for warranty conditions.

ADJ thanks you for purchasing this product.
For extensive service, please visit the website: www.adj.it
Do not open or repair this device. Do not use the divice in a damp environment. Clean the device with a dry cloth. The device meets the essential requirements and other relevant conditions of the applicable European directives. Please use the product only for the pur-pose for which it was designed. It is forbidden any other use or modification.

Warranty
This product is guaranteed against any manufacturing defect, based on the D.Lgs. Fe-bruary 2, 2002, No 24. In case of failure, please contact the retailer where you purchased it. Please check www.adj.it for warranty conditions.

The symbol of the crossed out trash indicates that the product, at the end of its useful life, must be treated separately from domestic waste and must be taken to a recycling center for electrical and electronic equipment or delivered to the seller when buying a replacement. The separate waste collection contributes in preven-ting possible adverse effects on the environment and health and promotes the recovery of which it is made. You are responsible for assigning the equipment in question at the appropriate waste disposal center. For more detailed information contact your local wa-ste disposal service or the shop where it was purchased. Anyone who does not carry the product in a recycling center for electrical and electronic waste shall be punished with administrative penalty provided by law on the illegal disposal of waste.

Browse the catalog on line!
http://www.adjpoint.com/catalogo/index.html

Made in China – Imported and distributed by IoT Tecnologie s.r.l. Via della Faeta, 1 – 00030 San Cesareo (RM) – ITALY

Features

• Supports USB 3.1 GEN2, super high speed up to 10Gbps,GEN1 high speed 5Gbps. Complied with USB 3.0/2.0/1.1
• Supports Windows 7/8/10/11, Mac OS 9.2, Linux 2.4.2 and above
• Supports M.2 PCIe/NVMe SSD, up to 1TB or more, fits size: 30×22 mm/42×22 mm/ 60×22 mm/80×22 mm
• LED power/status indicators
• Easy installation
• Color: Black

System Requirements
PC Requirements

• Minimum Intel Processor Pentium II/50MHz, 64MB RAM
• Windows 7/8/10/11
• Active USB port

MAC Requirements

• Minimum Apple G processor, 64MB RAM
• Mac OS 9.1, 9.2, 10.1.5, 10.2, 10.3
• Active USB port

Packing Contents

• M.2 PCIe Device
• User manual
• USB 3.1 super-speed Cable

Installation hard disk driver

1. Step 1: Push with finger as shown in the location and direction of picture to open the lower cover
2. Step 2: Insert PCIe SSD into the connector on the corresponding PCBA. Fasten with pressing parts.
3. Step 3: Close the bottom cover, push as shown the direction of picture.

Connect to computer
Connect one end (Type C) of the USB cable into the USB Port of your SSD external enclosure. Connect the other end of the USB-C cable into any active USB-C port of the computer.
Let Windows search and install the driver automatically.
Open “My Computer” to see your external hard drive ready to use.

NOTE:
If the external hard disk is a new disk drive which has not been partitioned, please refer to the Partition the External Hard Disk chapter to prepare your USB external disk.

Drivers Installation

Windows 7/8/10/11
The product is supported by Mass Storage Device within Windows 7/8/10/11 system directly you do not need to install any drivers. When the USB External Drive is used for the first time your PC system will detect a USB Storage Device and automatically install the drivers for [USB Mass Storage Device] from the installed system.
Mac OS
Mac OS 8.6
If you are using Mac OS 8.6, the software of Mass Storage Support 1.3.5 is required for installation. You can download The USB Mass Storage Support 1.3.5 from the Apple Software Updates web site https://support.apple.com/.
Mac OS 9.0 or later
You don’t need to install this software if you have installed Mac OS 9.0 or above. When you connect the product with the Mac computer, the mass storage volume should appear on the desktop in a few seconds automatically.

Disconnect to computer

Windows 7/8/10/11

1. Double-click on the [Unplug arrow icon or Eject Hardware] icon in the system tray. Dialog box appears as on the right.
2. Highlight the [USB Mass Storage Device] in the dialog box, click on [Stop], choose the USB External Drive that you want to disconnect, then click on [Stop] again on next screen.
3. Wait for few seconds, the system prompts “You may safely remove this device”.
4. You can now safely switch off the enclosure or unplug the USB cable from the USB port of the computer.

Mac OS
When disconnecting your product from the computer, close all windows and quit all run-ning applications that are stored on the USB External Drive and drag USB External Drive’s icon into “Trash” this dismounts it from the Desktop prior to unplugging the USB External Drive from the USB port.

How to partition the external hard disk

WARNING!
Before you partition your hard disk, please be aware that this will destroy all your existing data on the drive, so make sure you have a backup! This step is usually only required
the first time you install a factory new hard drive or if you want to change the existing format.

Windows 7/8/10/11

• Step1
  Right-click on [My Computer] , choose [Manage]. A [Computer Management] window will appear.

• Step2
  Click on [Disk Management] on the left part of this window and all connected disk drives will be listed in the right part. Find the Hard Disk that you added with it’s partition status on the right. You can create a new or delete an existing partition by right clicking on this area.

• Step3
  Right-click on the hard disk partition status area and choose [New Partition…].
  The “New partition wizard” will appear.

• Step4
  Following the “wizard” instructions to partition and format your HDD

• Step5
  Wait until “wizard” finish formatting your drive. It should now appear in [My Computer] ready to use.

• Attention:
  About Windows 7/8/10/11, please choose NTFS Format, When the capacity is blow 32GB, You can choose FAT32 format.

Mac OS
NOTE:
Mac OS does not recognize NTFS formatted drives.
Mac OS9.2 and earlier, does not support creating partitions on an external drive. To do that, you would need to purchase additional third-party software. Initializing is no pro-blem on all Operating Systems.

Mac OS X, use the Disk Utility to format and create partitions on your external disk.

• Select “Disk Utilities” in the utilities folder.
• Choose your external drive and format it according to your requirement.

FAQs

• Q: I can’t find the drive under my computer, why?
  A: Please make sure your new hard disk has been partitioned.

• Q: After plugging the USB port, the drive is not spinning at all, why?
  A: The USB cable doesn’t connect successfully

• Q: After installing the drive. Why it is still recognized as “Unknown device”
  A: This means the USB 3.1 HOST driver installation is not successful; Try disconnecting the cable, waiting 10s,and then reconnecting it. If the drive is still not recognized, restart your computer and try again.

• Q: Can I use external USB hub?
  A: Yes, USB hub works in the same way as the computer USB ports

• Q: My computer doesn’t have USB 3.1 port, Can I use USB 3.1 host Adapter ?
  A: USB 3.1 host adapter works in the same way as the built-in USB ports.

www.adj.it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>