DYNACRAFT BM215 6V Toyota Land Cruiser Owner’s Manual

June 10, 2024
DYNACRAFT

BM215 6V Toyota Land Cruiser
Owner’s ManualDYNACRAFT BM215 6V Toyota Land
Cruiser

This manual contains important safety, performance and maintenance information. read the manual before taking your first ride or allowing your child to ride your new  electric ride-on toy. keep the manual handy for future reference.

| DO NOT RETURN THIS ITEM TO THE STORE CONTACT DYNACRAFT CUSTOMER SERVICE FOR ASSISTANCE
dynacraftwheels.com/contact
or 1-800-551-0032| BC
---|---|---

FOR AGES 3+
MAXIMUM WEIGHT: 65 lb (29.5 kg)
NOTE: Illustrations in this Manual are for reference purposes only and may not reflect the exact appearance of the actual product. Specifications are subject to change without notice.

SPECIFICATIONS

SUITABLE AGE————————————–3+
CAPACITY————————————–Up to 65 lb (29 5 kg)
SPEED————————————– 2.5 MPH
CHARGER / INPUT————————————–AC120V / 60HZ
OUTPUT————————————–DC6V / 1A
CHARGING TIME————————————–12-18 Hours
BATTERY————————————– 6V 7AH, 1x Battery
SIZE————————————–126 x 73 x 58 cm
AVERAGE BATTERY LIFE————————————–300 Charges
This is an estimate only, not a guarantee. Actual battery performance will vary based on many factors, including but not limited to maintenance, charging habits, operation of  product, and temperature.

INTRODUCTION, SAFETY AND WARNINGS

ABOUT THIS MANUAL: This Manual was written to help you and your child get the most performance, comfort, enjoyment and safety when riding your new electric  ride-on toy. It is important for you to understand your new electric ride-on toy. By reading this manual before you let your child go out on his/her first ride, you will know  how to get the most from your new electric ride-on toy. It is also important that you or your child’s first ride be in a controlled environment, away from cars, obstacles, and other riders.
GENERAL WARNING: Riding an electric ride-on toy can be a dangerous activity, even under the best of circumstances. Proper maintenance of your new ride-on toy is your responsibility and helps reduce the risk of injury. Certain conditions may cause components to fail without fault of the manufacturer. The ride-on toy can and is intended to
move, and it is therefore possible to lose control, fall off and/or get into dangerous situations that no amount of care, instruction or expertise can eliminate. If such a thing  does occur, your child can become seriously injured or die, even when using safety equipment and other safety precautions.
WARNING: To reduce risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than one (1) rider.
WARNING: CHOKING HAZARD–Small parts not suitable for children under 3 years old.
WARNING: This ride-on toy is intended to be ridden on smooth, level ground. Do not ride in loose dirt, sand, or gravel, which could damage moving parts, the motor, or  the electrical system.
WARNING: Do not ride in rain, snow, or mud, or store the ride-on toy outside without covering. Water can damage components, including the motor, electrical system, and battery.
NOTE: Store the ride-on toy indoors when not in use or in a covered location. Avoid long term exposure to rain, excessive sun, or other inclement weather.
RIDE AT YOUR OWN RISK AND ALWAYS USE COMMON SENSE. This manual contains many warnings and cautions concerning the consequences of failing to  inspect, maintain or properly use your electric ride-on toy. Because any fall can result in serious injury or even death, we do not repeat the warning of possible serious injury  or death each time such a possibility is mentioned in this manual or the risk of falling leads to a warning.
ALWAYS USE PROPER RIDING ATTIRE. Always wear appropriate clothing and shoes.
Never ride barefoot or in sandals and make sure that shoelaces or other fasteners are tied and kept away from the wheels and drive system of the ride- on toy.

RIDER USE AND REQUIRED PARENTAL SUPERVISION
RIDERS MUST NOT EXCEED THE WEIGHT LIMIT OF 65 LB (29.5 KG) AND MUST BE OVER 3 YEARS OLD. NEVER ALLOW MORE THAN 1 CHILD TO RIDE THE RIDE-ON TOY SIMULTANEOUSLY. The age grade for the electric ride-on toy is for 3 years and older. Just because your child is within the age and weight limitations specified for the electric rideon toy, does not mean that his/her size is appropriate to fit or maintain control of the electric ride-on toy, or that he/she is capable of safely operating the electric ride-on toy. You are the best judge of whether you or your child can safely operate the electric ride- on toy; this includes determining whether your child is at the appropriate developmental stage for safe use of the electric ride-on toy. Any rider that is unable to fit comfortably on the electric ride-on toy should never attempt to ride it. A parent’s decision to allow their child to use the electric ride- on toy should be based on the child’s maturity, skill and their ability to follow rules. Remember that the electric ride-on toy is intended for use only by children who are, at a minimum, able to comfortably and safely operate it. Children operating the electric ride-on toy should be supervised by an adult at all times. Parents should ensure that children only use the electric ride- on toy safely and within their age and physical limits. This manual contains very important safety information. It is your responsibility to completely review this information and make sure that all riders understand all of the warnings, cautions, instructions and safety topics addressed in this manual and to assure that all riders are able to safely and responsibly use the electric ride-on toy. You should periodically review and reinforce all information in this manual with all riders, especially children. You should also regularly inspect and maintain your electric ride-on toy to ensure the safety of all riders. Make sure that your new electric ride-on toy is properly fitted to any child riding

SAFE RIDING PRACTICES AND WARNINGS

  • Check and obey all local laws or regulations which may be in effect in the locations where the electric ride-on toy may be used.

  • Always wear appropriate clothing and shoes.

  • Observe the age and weight limitations on the cover of this manual.

  • Always stay seated while riding the electric ride-on toy. To stop you must take your foot off the foot pedal.

  • Children must be supervised by an adult at all times to be safe.

  • Always be alert and ride your electric ride-on toy defensively. Watch out for obstacles that could catch one of the electric ride-on toy’s wheels or force you to turn  suddenly and/or lose control. Be careful to avoid pedestrians, persons using other wheeled products (including roller or in-line skates, skateboards, scooters, bikes, etc.),  children or animals who may enter your path. Always respect the rights and property of others.

  • Do not activate the foot pedal unless you are seated in the ride-on toy and in a safe, outdoor environment that is suitable for riding your electric ride-on toy.

  • Do not attempt or perform any stunts or tricks on the electric ride-on toy. It is not made to withstand such misuse and abuse.

  • Keep both hands on the steering wheel at all times.

  • Do not touch the motor on the electric ride-on toy when in use or directly after use as these parts can become extremely hot.

  • Never allow more than one child to ride the electric ride-on toy at one time and never try to tow anything.

  • Do not use near steps, water, or swimming pools.

  • Do not ride in wet weather.

  • Never immerse the electric ride-on toy in water; electrical and drive components could be damaged by water or create other potentially unsafe conditions.

  • Keep your fingers and other body parts away from the motor, steering system, wheels and all other moving components.

  • Never hitch onto another vehicle or let yourself be pulled or pull anyone or anything while riding the electric ride-on toy.

  • Ride only on smooth, flat, dry surfaces such as pavement or level ground without loose debris, such as sand, leaves, rocks or gravel. Water, mud, ice, bumpy, un-even,  slick, or rough surfaces could impair traction and contribute to possible loss of control.

  • Do not ride on or near hills or steep inclines. Ride only on level ground to avoid tip over.

  • Avoid sharp turns, bumps, drainage grates, and other obstacles.

  • Do not ride at night or where there is limited visibility.

  • Do not ride indoors or on surfaces that could become damaged such as carpet or flooring.

  • Do not ride on streets, around cars, or in foot or vehicle traffic.

  • Regularly check the electric ride-on toy and its components. If any parts are broken or worn, do not ride the electric ride-on toy until you have fixed or replaced the  broken or worn parts. Contact our Customer Service Team at dynacraftwheels.com/contact for replacement parts.

  • Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with wheels or other moving parts.

  • Before each cycle of operation, you must perform the preoperation checks specified in this manual or by the manufacturer, including:
    – That all guards and pads originally supplied by the manufacturer are in proper place and in serviceable condition;
    – That the area that the unit is to be operated in is safe and suitable for safe operation;
    – That all safety labels are in place and understood by everyone, including the riders;
    – That any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition; and
    – That tires/wheels are in good condition and have sufficient tread remaining.

  • Avoid sharp bumps, drainage grates, and sudden surface changes.

PRE-RIDE SAFETY CHECKLIST

  • Check to make sure that all components are properly secured and are functioning according to the manufacturer’s specifications.
  • Components must be maintained and repaired and only with the manufacturer’s authorized replacement parts. Installation should be performed only by adult, qualified  personnel. Please contact our Customer Service Team at dynacraftwheels.com/contact for replacement parts.

USING THE CHARGER
The charger should be examined regularly for damage to the cord, plug, enclosure and other parts. In the event such damage has occurred, the electric ride-on toy should not  be charged until the charger has been repaired by qualified personnel or replaced. Use only the supplied, recommended charger.

  • Always use caution when charging.
  • The charger is not a toy and should be operated by an adult.
  • Never operate the charger near flammable materials or liquids, and operate the charger in well-ventilated areas.
  • Disconnect the charger and unplug it from the electric ride-on toy when not in use.
  • Do not exceed the recommended charging time.
  • Always disconnect the charger from the electric ride-on toy prior to wiping down or cleaning the electric ride-on toy.

WARNING: Never modify or alter the electrical system. Risk of fire. Do not bypass fuses. Replace 25A fuse (located under the seat) only with 25A fuse and 3A fuse (located under the foot pedal) only with 3A fuse. Alterations could cause a fire or explosion resulting in serious injury or death and could also ruin the electrical system.
FAILURE TO HEED THE WARNINGS LISTED ABOVE INCREASES RISK OF POTENTIALLY SERIOUS INJURY. USE THE APPROPRIATE CAUTION  WHEN RIDING AND ALWAYS WEAR APPROPRIATE CLOTHING AND SHOES.

BEFORE YOU BEGIN ASSEMBLY

NOTE: Remove all packing and items from the display box. Make sure that the power switch is turned “OFF” before assembling the electric ride-on toy.
ESTIMATED ASSEMBLY TIME
You should allow approximately 30 minutes for assembly, not including initial charging time. Initial charging can take approximately 18 hours (see pages 14-15 for charging information).
WARNING: DO NOT USE NON-ORIGINAL OR NON-RECOMMENDED PRODUCTS WITH YOUR ELECTRIC RIDE-ON TOY.
Altering of the original components or use of non-recommended replacement parts may or may not be compatible with the design and will void the warranty and may cause  an unsafe condition resulting in serious injury or death. Contact our Customer Service Team for original replacement parts at dynacraftwheels.com/contact.

If you experience a problem with this product, or are missing a part, please contact our Customer Service Team at dynacraftwheels.com/contact, rather than return this product to the store.
Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.

PARTS DIAGRAM

DYNACRAFT BM215 6V Toyota Land Cruiser - DIAGRAM

1  Plastic Body Assembly x1 12  View Mirror x2
2 Ø12 Washer x10 13  Seat x1
3  Wheel x3 14  Wheel Box x1
4  Driver Wheel x1 15  4×16 Round Head Screw x2
5  M10 Lock Nut x4 16  M5x16 Machine Screw x1
6  Wheel Cover x4 17  Split Pin x1
7  Steering Column x1 18  Ø5 Washer x1
8  Rear Axle x1 19  Socket Wrench x2
9  Steering Wheel x1 20  Audio Input Cable x1
10  M5x30 Machine Screw x1 21  Charger x1
11  M5 Locknut x1

NOTE: Some parts shown are assembled on both sides of ride-on toy. Parts are packaged at both ends of box and in ride-on chassis. Ensure all parts are present before assembly.

ASSEMBLY

Your new ride-on toy requires adult assembly. Please set aside around 30 minutes for assembly. Please identify all parts before assembly and save all packaging material until  assembly is completed to ensure that no parts are discarded.
TOOLS REQUIRED:

Phillips Screwdriver
(not included)| Needle-nose pliers
(not included)| 17 mm Socket Wrench
(included)
---|---|---
DYNACRAFT BM215 6V Toyota Land Cruiser - TOOLS

WARNING: Children can be harmed by small parts, sharp edges and sharp points in the ride-on toy’s unassembled state, or by electrical items. In the unassembled state, this package contains small parts. Adult assembly is required; children should not handle parts, or help in assembly of the ride-on toy.

FRONT AXLE ASSEMBLY

  • Gently turn the ride-on toy body upside down and cut off the plastic tie on the front axle with scissors.
  • Remove the M5x16 screw, washer and M5 locknut from the front axle.
  • Adjust the front axle so that the axle is in the correct position as shown below; then reinsert the M5x16 screw as shown, making sure the M5x16 screw goes through the  holes in metal plates A and B (ensure plate A sits over plate B as shown with the stopper, to prevent fingers from becoming trapped while steering); attach the washer  and the locknut, tighten securely with an adjustable wrench or needle-nose pliers.
    DYNACRAFT BM215 6V Toyota Land Cruiser - ASSEMBLY 1

WARNING: Make sure front axle assembly is properly secured before letting anyone use the ride-on toy.

FRONT WHEEL ASSEMBLY

  • Remove all parts from front axle.
  • Fit a Ø12 washer onto the axle.
  • Slide the wheel onto the axle.
  • Install a Ø12 washer and locknut, then tighten it. NOTE: Do not overtighten.
  • Fasten the wheel cover.
  • Repeat above operation for the front wheel on the other side.

REAR AXLE ASSEMBLY

  • Remove all parts from rear axle.
  • Cut off the plastic tie on the right gear box.
  • Slide a Ø12 washer from longer end to A stopper.
  • Insert the rear axle through the hole in the ride-on toy body and follow arrow direction as shown.

NOTE: Lift the gear box so that the rear axle can go through it and protrude out.

RIGHT DRIVE WHEEL ASSEMBLY

  • Slide the drive wheel onto the axle and make it match up with the gear box.
  • Slide a Ø12 washer onto the axle.
  • Install the M10 locknut and tighten it. NOTE:Do not overtighten.
  • Fasten the wheel cover.

LEFT REAR WHEEL ASSEMBLY

  • Fit a Ø12 washer onto the other end of the rear axle.
  • Slide a wheel onto the rear axle.
  • Install another Ø12 washer and a locknut, then tighten it. NOTE: Do not overtighten.
  • Fasten the wheel cover.

WARNING: Make sure that the axle assemblies and wheels are properly tightened and secure before letting anyone use the ride-on toy. Failure to do so may result in a loss of control and serious injury or death.

IMPORTANT! CHECK GAP AFTER ASSEMBLING WHEELS
After assembling any wheel onto the axles, make sure to check the gap between the screw thread and the outside of the wheel (refer to the adjacent diagram). If the gap is too big, add two or three  washers on the axle to the inside of the wheel. After tightening the nut on the outside of the wheel, please turn the wheel with your finger to check if the wheel can run smoothly. This is a very  important step because if the wheel can run smoothly, it is ok; but if the nut presses the wheel and the wheel can’t run smoothly, the motor will be broken easily! If the wheel does not run smoothly,  you will need to decrease on or two washers to make sure the wheel can run smoothly!

NOTE: If the wheel nuts are loose, the wheels will not engage the forward gear. Tighten the nut with the wrench.

STEERING COLUMN ASSEMBLY

  • Turn the ride-on toy on its side as shown in the diagram below.
  • Slide a Ø12 washer onto the steering column from the straight end.
  • Insert the straight end of steering column up through the bottom hole at the front of ride-on toy body, and out through the hole in the dash board.
  • Insert the bent end of steering column through the hole in the front axle linkage.
  • Fit a Ø12 washer onto the bent end of the steering column.
  • Insert a split pin into the hole in the bent end of steering column, and split it using needle-nose pliers (to assure the washer will not fall out).
    DYNACRAFT BM215 6V Toyota Land Cruiser - washer

WARNING: Make sure that the steering column assembly is secure and steers properly before letting anyone use the ride-on toy. Failure to do so may result in a loss of control and serious injury or death.

STEERING WHEEL ASSEMBLY

  • Gently turn the ride-on toy body upright.
  • Remove the M5x30 machine screw and M5 locknut from the steering wheel.
  • Insert the steering wheel onto the end of the steering column, line up the hole in the steering wheel and the hole in the steering column, reinsert the M5x30 machine screw as shown, and tighten  it with M5 locknut securely.

WARNING: Make sure that the steering wheel is securely fastened and that the steering functions properly before letting anyone use the ride-on toy.

STEERING WHEEL BATTERIES INSTALLATION
NOTE: Batteries are not included.

  • Unscrew the screw in the steering wheel and remove the cover.
  • Insert 2x 1.5V size AA AM-3 or LR6 batteries.
  • Replace the cover and tighten the screw to secure it in place.

STEERING WHEEL BATTERY SAFETY INFORMATION:

Batteries may leak fluids that can cause chemical burn, injury or ruin your product.
To avoid battery leakage:

  • Install batteries correctly, observing the polarity (+/-) signs to avoid leakage.
  • Do not mix old and new batteries.
  • Do not mix batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (NiMH).
  • Remove the batteries from the battery compartment when the unit will not be used for an extended period of time.
  • Always remove exhausted batteries from the battery compartment.
  • Do not dispose of batteries in fire.
  • Do not short circuit the supply terminals.
  • Replace the batteries when the horn sounds become distorted.
  • Non-rechargeable batteries should not be recharged.
  • Use only batteries of the same or equivalent type as recommended.
  • If rechargeable batteries are used, they should only be charged by an adult.
  • Remove rechargeable batteries from the product before charging.
  • Battery chargers used with toys must be examined regularly for damage to the cord, plug, enclosure and other parts. In the event that such damage is found, the toy must not be used with the  battery charger until the damage has been repaired.

POWER SUPPLY CONNECTION
NOTE: The battery is disconnected for shipment to prevent the battery from draining.

  • Plug the wire connector into the battery connector as shown.

SEAT ASSEMBLY

  • Insert the clips on back of the seat into the slots in the back of the ride-on toy body, and slide into place as shown.
  • Tighten the seat with two M5x16 machine screws (which are stuck on the seat).
    NOTE: Check to ensure the seat is snug in place after assembly.

VIEW MIRRORS ASSEMBLY

  • Insert the view mirror into the hole in front of the ride-on toy body and push until you hear it click into place.
  • Repeat for the other side.

WHEEL BOX ASSEMBLY

  • Open the wheel box, and insert the wheel box into the hole in back of the ride-on toy body.
  • Tighten the wheel box with two 4×16 round head screws, and close the box.
    DYNACRAFT BM215 6V Toyota Land Cruiser - WHEEL

CONNECT AUDIO INPUT CABLE

  • Plug the audio input cable on AUX line-in jack on the ride-on toy. (You can connect the cable with an audio device or MP3 player whenever you want to play).
    NOTE: Store the audio input cable in a safe place when not in use.
    DYNACRAFT BM215 6V Toyota Land Cruiser - CABLE

BATTERY CHARGING

IMPORTANT! Before first time use, charge the battery for at least 18 hours. Charge the battery for at least 12 hours after each use of the ride-on toy. Never charge the battery longer than 30 hours.  Overcharging or undercharging the battery may shorten battery life and decrease ride-on toy running time.
WARNING: Battery can fall out and injure a child if the ride-on toy tips over.
Always use battery retainer.
PREVENT FIRE

  • Never modify the electrical system.
  • Alterations could cause a fire resulting in serious injury and could also ruin the electrical system.
  • Use of the wrong type battery or charger could cause a fire or explosion, resulting in serious injury.
  • Use of non-original components on this ride-on toy could cause overheating, fire or explosion.
  • The battery must be handled by adults only.
  • The battery is heavy and contains sulfuric acid (electrolyte).
  • Dropping the battery could result in serious injury.
  • Never allow children to charge the battery.
  • Battery charging must be done by adults only. A child could be injured by the electricity involved in charging the battery.
  • Never lift or carry the battery by the wires or connector, this can damage the battery and possibly cause a fire resulting in serious injury. Lift and carry the battery by the case only.
  • Read the safety instructions on the battery.
  • Examine the battery, charger and their connectors for excessive wear or damage each time you charge the battery.
  • If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.

CAUTION: Use the charger in dry locations only.
IMPORTANT NOTE

  • We recommend that you start charging your battery before beginning assembly of your new ride-on toy.

  • The battery must be upright while charging.

  • The charger is not a toy, and should only be operated by adults.

  • Do not short-circuit the battery.

  • You do not need to remove the battery from your ride-on toy to recharge it.

  • Before charging the battery, examine the battery case for cracks and other damage which may cause sulfuric acid (electrolyte) to leak during the charging process. If damage is detected, do not  charge the battery or use it in your ride-on toy. Battery acid is very corrosive and can cause severe damage to surfaces it contacts.

  • Use only an original charger (AC 120V 60Hz) with an output of DC 6V (1A) to charge your ride-on toy battery.

  • NOTE TO ADULTS: Regularly examine the charger for damage to the cord, plug, housing or other parts that may result in the risk of fire, electric shock or injury.

  • If your battery is old and will not accept a charge, do not leave it in the ride-on toy. Always remove a dead battery from the ride-on toy.

  • After the first charge, recharge the battery for at least 12 hours after each use.
    Never charge the battery longer than 30 hours. Charge the battery after each use, regardless of how long the ride-on toy was used.

  • Do not allow the battery to run down completely before charging.

  • Charge the battery before storing the ride-on toy.

  • Charge the battery at least once per month, even if the ride-on toy has not been used.

NOTE:

  • This product has CHARGING PROTECTION: when charging, all the functions will be cut off.
  • The POWER SWITCH must be switched to the OFF position when charging.
  • Recharges after initial charge – At least 12 hours, and never charge the battery longer than 30 hours.
  • When the ride-on toy begins to run slowly, recharge the battery.
  • After each use or once a month minimum recharge time 12 hours, less than 30 hours at most.

CAUTION: Use the charger in dry locations only.DYNACRAFT BM215 6V
Toyota Land Cruiser - locations

  1. Plug the charger port into the input socket (the socket is under the seat).
  2.  Plug the charger plug into a wall outlet. The battery will begin charging.
    NOTE: Red LED light indicates battery is charging and a green LED light indicates battery is nearly fully charged. (If the lights on the charger do not light up, check the power to the outlets.) If  you have any charging questions or issues, please make sure that you have charged your unit according to the recommended charging times outlined in this manual, i.e., at least 18 hours before  first use and at least 12 hours after each subsequent use, before contacting our Customer Service Team.

HOW TO USE YOUR RIDE-ON TOY

DYNACRAFT BM215 6V Toyota Land Cruiser - TOY

POWER SWITCH
Turn the ride-on toy on or off.
FORWARD

  1. Shift the “Forward/Stop/Reverse” Shift Lever to Forward position.
  2.  Press the Foot Pedal, and the ride-on toy will move forward.

STOP

  1. The ride-on toy will stop when your child’s foot is removed from the Foot Pedal
  2. Shift the “Forward/Stop/Reverse” Shift Lever to middle position to stop even if your child’s foot is still pressing on the foot pedal.

REVERSE

  1. Shift the “Forward/Stop/Reverse” Shift Lever to Reverse position.
  2. Press the Foot Pedal, and the ride-on toy will move backward.

FRONT LIGHTS
The front lights will light up when the Foot Pedal is pressed.
SOUND BUTTON
Press the button on the steering wheel to activate sound.
AUDIO INPUT JACK
Use the audio input cable (included) to connect your MP3 player or other compatible audio device with this ride-on toy to listen to and enjoy music.

  1. Plug one end of the audio input cable (included) into the audio input jack on the ride-on toy as shown.
  2. Plug the other end of the audio input cable into the headphone jack on your audio device or MP3 player.
  3. Adjust your audio device or MP3 player volume to low level and turn the power switch on your ride-on toy to the “ON” position.
  4. Then adjust the volume to increase or decrease its sound level as desired.
    DYNACRAFT BM215 6V Toyota Land Cruiser - adjust

NOTE: MP3 player or Audio device not included.
WARNING: Do not let use of the sound button, an MP3 player, or other audio devise interfere with safe riding.
IMPORTANT
Always stop ride-on toy when changing the direction to avoid damage to the gears and motor.

  • This ride-on toy has an adjustable seat belt; please instruct children on how to fasten the seat belt before using.
  • Do not let any child touch the wheels or be near them when the car is moving.
  • Make sure you come to a complete stop before changing directions from forward to reverse.
  • To avoid accidents, please inspect the ride-on toy before riding to ensure that it is in proper working order and safe to ride.
  • Protective equipment should always be worn.
  • This toy has no brake; to stop, remove foot from foot pedal.
  • Check all the screws, cap nuts and protective coverings regularly and tighten as required. Check plastic parts on a regular basis for cracks or broken pieces.

NOTE

  • Always make sure the power switch is in the “OFF” position whenever the rideon toy not in use.
  •  Batteries may become damaged and no longer accept a charge if power switch is left in the “ON” position when not in use.
  • Never store the product in outdoor conditions, never store it in the rain, and never store the product in freezing or below freezing temperatures. These low temperatures will permanently damage the battery.

SAFETY PRECAUTIONS

  • Your new battery must be charged for at least 18 hours before you use it in your ride-on toy for the first time.
  • Children must have adult supervision at all times.
  • Do not ride on the road, footpaths, near pools, or bodies of water.
  • Do not allow children under the recommended age to ride the ride-on toy; please refer to the age grading.
  • Do not allow riders over the recommended weight rating or outside of the recommended age range to use the ride-on toy.
  • To “stop” you must take your foot off the pedal.
  • Charging should only be done by an adult.
  • An adult must teach the child how to operate the ride-on toy.
  • Do not ride on hills or slopes, or in sand, or on other soft, wet, or slippery surfaces.
  • Do not use a different size battery. Use only original or recommended replacement batteries.
  • The ride-on toy is designed to carry only one rider at a time. Never allow more than one rider or over-load the ride-on toy.
  • This product should be assembled and checked by adults before use.
  • Don’t wash the ride-on toy with water. Just clean it with a cloth.

DETAILED MAINTENANCE AND REPAIR

WARNING: Turn power “OFF” before conducting any maintenance procedures.

TOOLS REQUIRED:

Phillips Screwdriver
(not included)| Flat head Screwdriver
(not included)| 17 mm Socket Wrench
(included)
---|---|---
DYNACRAFT BM215 6V Toyota Land Cruiser - Screwdriver

HOW TO REPLACE FRONT WHEELSDYNACRAFT BM215 6V Toyota Land Cruiser -
FRONT

  1. Remove the wheel cover with a flat head screwdriver.
  2. Remove the M10 locknut with a 17 mm socket wrench.
  3. Remove the Ø12 washer.
  4. Remove the wheel, then replace with a new one.
  5. Remount the Ø12 washer, M10 locknut and securely tighten the wheel; then reinsert the wheel cover.

WARNING: Make sure that wheels are securely attached before letting anyone use the ride-on toy.

HOW TO REPLACE RIGHT DRIVE WHEEL AND GEAR BOXDYNACRAFT BM215 6V Toyota
Land Cruiser - GEAR BOX

  1. Gently turn the ride-on toy upside down.

  2. Remove the wheel cover with a flat head screwdriver.

  3. Remove the M10 locknut with a 17 mm socket wrench.

  4. Remove the Ø12 washer.

  5. Remove the wheel, then replace with a new wheel.
    IF YOU DO NOT NEED TO REPLACE THE GEAR BOX, PLEASE PROCEED TO STEP 11.

  6. Unscrew the four screws on the motor cover under the toy body with a screwdriver, and remove the motor cover.

  7. Unplug the motor output connector that is connected to the gear box.

  8. Remove the gear box and replace with a new one.

  9. Plug the motor output connector back into the gear box.

  10. Remount the motor cover with the four 4×16 round head screws.

  11. Replace the Ø12 washer and the M10 locknut, and tighten securely; then re-insert the wheel cover.

  12. Gently turn the ride-on toy upright.

HOW TO REPLACE LEFT REAR WHEELDYNACRAFT BM215 6V Toyota Land Cruiser -
LEFT

  1. Remove the wheel cover with a flat head screwdriver.
  2. Remove the M10 locknut with a 17 mm socket wrench.
  3. Remove the Ø12 washer.
  4. Remove the left rear wheel, then replace it with a new wheel.
  5. Remount the Ø12 washer and M10 locknut, securely tighten the wheel, then reinsert the wheel cover.

WARNING: Make sure the wheels are securely attached before letting anyone use the ride-on toy.

HOW TO REPLACE THE BATTERYDYNACRAFT BM215 6V Toyota Land Cruiser -
BATTERY

  1. Unscrew the screws on the seat with a screwdriver, and remove the seat.
  2.  Use a screwdriver to remove the two screws from the battery retainer.
  3. Unplug the wire connector (which is connected to the battery connector).
  4. Carefully lift the dead battery and replace it with a new one.
  5. Replace the battery retainer and secure it with the screws. Plug the wire connector into the battery connector and replace the seat, making sure to securely fasten it with the M5x16 machine  screws removed in step 1.

HOW TO REPLACE THE POWER SWITCHDYNACRAFT BM215 6V Toyota Land Cruiser -
SWITCH

  1. Remove the power switch with a flat head screwdriver (not included).
  2. Unplug the main connector from the power switch socket as shown.
  3. Plug in the new power switch for replacement.
    NOTE: Don’t let the power switch socket drop into the body of the unit.

HOW TO REPLACE THE FOOT PEDAL

DYNACRAFT BM215 6V Toyota Land Cruiser - PEDAL

  1. Use a flat head screwdriver to gently pry the LEFT side of foot pedal.
  2. Gently remove the foot pedal.
  3. Disconnect the old foot pedal from the pedal switch socket.
  4. Replace and reconnect the new foot pedal to the pedal switch socket to ensure they are connected in the correct position (see Figure 3) and then insert the right side of the foot pedal into the  foot pedal compartment first, and gently push down on the left side of the pedal so that it snaps into place.

BATTERY CARE AND DISPOSAL
Do not store the battery in temperatures above 75° F (23.5° C) or below 32° F (0°C).
THIS PRODUCT CONTAINS SEALED LEAD ACID BATTERIES WHICH MUST BE RECYCLED IN ACCORDANCE TO YOUR LOCAL AND STATE  LAWS PLEASE CAREFULLY READ AND UNDERSTAND THE FOLLOWING DISPOSAL INSTRUCTIONS:

DISPOSAL: This product contains sealed lead acid batteries which must be disposed of or recycled in an environmentally safe manner. Do not dispose of the batteries in your household trash. Do  not dispose of the batteries in a fire, as the battery may explode or leak. The incineration, disposal in landfill and/or placing sealed lead acid batteries with household trash is prohibited by law in most  areas. Return exhausted batteries to a state or federal approved lead acid battery recycler or check with your local retailer of vehicle batteries. If you live in Florida, Minnesota or various other states, it  is prohibited by law to throw away lead-acid batteries in the municipal waste stream. Check local laws for proper handling and recycling of lead-acid batteries.

WARNING:

  • Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
  • If a battery leak develops, avoid contact with the leaking acid and place the battery in a plastic bag. See instructions above for proper disposal. If acid comes into contact with skin or eyes, flush  with cool water for at least 15 minutes and contact a physician.
  • If acid is internally ingested, give water, milk of magnesia or egg whites immediately.
    Never give emetics or induce vomiting. Call a physician.

CARE

  • Leaving the battery in a discharged condition will ruin it.
  • Always remove an exhausted battery from the ride-on toy. Battery leakage and corrosion can damage the ride-on toy.
  • Do not store the battery in temperatures above 75° F (23.5° C) or below 32° F (0° C).
  • Use only a 6V 7AH battery. Remember to charge the new battery for at least 18 hours before first use.
  • Prevent the battery from moving freely inside the battery compartment. Always use the battery retainer to secure the battery in the battery compartment.
  • Examine the battery, charger and their connectors for excessive wear or damage each time you charge the battery. If damage is detected, do not use the charger or the battery until you have  replaced the worn or damaged part.

LIMITED WARRANTY

FREE WARRANTY UPGRADE WITH REGISTRATION CONSUMER ACTION REQUIRED dynacraftwheels.com/register
UPGRADE YOUR WARRANTY WITH PRODUCT REGISTRATION Free warranty upgrade with online registration at dynacraftwheels.com/register.
We respect your privacy. Any information collected by Dynacraft Wheels will never be shared with any other company or organization. See Dynacraft’s privacy policy for further information:  dynacraftwheels.com/dynacraft- privacy-policy.
BENEFITS OF SIGNING UP FOR FREE EXTENDED WARRANTY

  • Simple, quick sign up at dynacraftwheels.com/register (proof of purchase required).
  • Extra 6 months battery coverage from date of purchase.
  • Extra 60 days of coverage on electric ride-on parts subject to wear and tear, from date of purchase.
  • Transportation charges on replacement parts waived for the Limited Warranty period. See Limited Warranty for details.
    For further enquiries call Customer Service at 1-800-551-0032 or visit dynacraftwheels.com/contact

This Limited Warranty (“Warranty”) extends only to the original retail purchaser, who must provide proof of purchase to validate any claim As noted below, certain aspects of this Warranty can be extended free of charge to original retailer purchasers who also register their product using the provided online registration form Proper registration via Dynacraft’s online registration form is the only  way to obtain these noted extensions This Warranty is not transferable to anyone else and is the only warranty for your Dynacraft product, to the extent permitted by law No other express or  implied warranty is given, and except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose on this product is hereby disclaimed Part or  model specifications are subject to change without notice By purchasing and using your new electric ride-on toy you agree to be bound by the terms of this Warranty as set out below This Warranty is  subject to change without notice
What does this Limited Warranty cover? This Warranty covers all parts of the electric ride-on toy to be free from defects in workmanship and materials This Warranty is only effective if: the electric ride-on toy is used under normal conditions for its intended purposes, by a person that properly fits and is capable of controlling the vehicle; and the electric ride-on toy receives all necessary maintenance and adjustments
What is not covered by this Limited Warranty? This Warranty does not include labor and transportation charges You, the original purchaser will be responsible for labor or transportation charges associated with the repair or replacement of any parts found to be eligible for warranty coverage Those original purchasers who qualify for the extended version of this Warranty will have transportation charges waived for the duration of the Limited Warranty period This warranty does not cover damage caused by normal wear and tear, crash collision, misuse, abuse, neglect, improper  assembly, improper maintenance, lack of maintenance, alteration, or any similar damage to the ride-on toy This Warranty will be void if the electric ride-on toy is ever: installed with a motor or  modified in any other way; rented or used for commercial purposes; or used in a manner contrary to the instructions in the Owner’s Manual included with this product Dynacraft will not be liable for incidental or consequential loss or damage, due directly or indirectly from use of this product For how long does this Limited Warranty last? The ride-on toy, with the exception of the battery and  cosmetic parts as described below, is warrantied against defective materials or workmanship for a period of one year from the original date of purchase
The battery is warrantied against defective materials or workmanship for a period of six months from the original date of purchase For those original purchasers who qualify for the extended version  of this Warranty, the battery is warrantied for a period of one year from date of purchase Parts and accessories considered to be cosmetic and not essential for the operation of this electric ride-on toy  as well as those parts and accessories subject to normal wear and tear are warrantied against defective materials or workmanship for a period of 30 days from the original date of purchase An original receipt confirming the original date of purchase is required to validate your warranty For those original purchasers who qualify for the extended version of this Warranty, cosmetic/wear-and-tear  components are covered for 90 days from date of purchase Parts and accessories considered cosmetic include, but are not limited to: mirrors; doors; fenders; stickers/ decals; decorations/accessories;  and fur Coverings (for plush animal electric ride on toys) Parts and accessories subject to wear and tear include, but are not limited to wheels and wheel components What will Dynacraft do to honor  this Limited Warranty? Dynacraft will replace any component or battery confirmed to be defective and eligible for warranty replacement with the same or a functionally equivalent part You, the  original purchaser will be responsible for any and all labor or transportation charges connected with the replacement or repair of the ride-on toy or any covered parts How do you make a claim under  this Limited Warranty? Warranty claims should be submitted via Dynacraft’s online portal at dynacraftwheels.com/contact Please have your proof of purchase available before contacting to validate  your claim Products can be registered at dynacraftwheels.com/register

DO NOT RETURN THIS ITEM TO THE STORE
CONTACT DYNACRAFT CUSTOMER SERVICE FOR ASSISTANCE
dynacraftwheels.com/contact
or 1-800-551-0032
Please have the following information available:
Model Number
Example: 8000-00
Production Date
Example: MM.DD.YYYY
Serial Number
Example: DXXXX00000000
This information is provided on a white sticker located on your unit and is required to help us handle your request.
Please do not remove the sticker from your unit.

Dynacraft BSC, Inc.
1501 Crossgate Road
Port Wentworth, GA 31407
Call Toll Free 1-800-551-0032
dynacraftwheels.com
©2022 All rights reserved

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals