ADJ MW20 3D Egg Wireless Mouse User Manual
- June 10, 2024
- ADJ
Table of Contents
MW20 3D Egg Wireless Mouse
User Manual
cod. 510-00039 / 510-00040 / 510-00041 / 510-00042
Operating environment
In order to get the full entertainment for using this new advanced product, please follow the below tips:
- The receiver should be far away from the Monitor, disc driver or other electronic products, in order to prevent the radio disturbance, the suggested distance is above 20 centimeters.
- The radio signal can penetrate the non-metallic objects to achieve 360 degree transmit, but it can not penetrate the metal materials, so please do not put the mouse and the receiver onto the metallic tabletop.
- Please be sure there is no big size metal between the mouse and receiver to avoid the disturbance.
- Wireless mouse can be used on the surface with various colors and materials such a s wood, paper, clothing, etc. But for the glass and plastic surface, it is better to use the mouse pad.
- The actual receiving distance should be better than the standard, but if the mix-machine, motor, electric drill and other strong electronic equipment’s operating nearby, may lead to slowly receiving or other abnormal.
Tips:
- Check the receiver, be sure it is connected to the USB port
- Be sure that setting battery is right
- Check the reminding light is shinning or not
- Reduce the distance of receiver and mouse
- Please use the product only for the purpose for which it was designed. It is forbidden any other use or modification.
Additional compliance information:
To obtain additional information about the compliance, go ta
AD] website: www.adj.it/certification or
contact the AD] Customer Support to the following e-mail address:
supporto@adj.it
Made in China – imported and distributed by lost Technologies s.r.1.
Via Della Feta, 1 – 00030 San Cesario (RM) – ITALY
Congratulations for your choice o f this 2.4 GHz wireless optical mouse.
Please read the manual, before using.
Features
- 2.4GHz wireless mouse, 10M effective distance
- Optical engine, accurate positioning
- Nano receiver, plug and play
- Low current consumption
- Compatible with Windows® / Mac®
Tips:
- Please take out the battery if you do not use your wireless mouse for long time, laying aside cool and dry place preservation;
- Please do not use the battery if happens leaking, discoloration, distortion or other abnormity.
Battery installation into mouse
1. Open the battery cover
2. Put battery in correct direction
3. Cover the battery cover
In order to achieve the best economical effect, the intelligent power saving technology is adopted. When your mouse stops moving, it will switch to the power saving mode automatically. If your mouse stops working for about 8 minutes, it’ll enter the deep power-saving mode, which costs little battery.
Connection of the receiver
Connecting the receiver to the PC by the USB port, for desktop, USB extending
fort or front-set USB port i s better. When receiver plugs into USB port,
computer would detect the device automatically. Mouse could works normally
with ON mode. I f the mouse couldn’t work normally, should build up
connections between the mouse and receiver.
Building up connection between the mouse and receiver
Pull out the receiver from the USB port, press the left-right 3 mouse buttons
or the “connect” button at the bottom of mouse at first, the indicator on the
top of the mouse will flash at this time. Then, connect the receiver to the
USB Port, the distance between mouse and receiver i s about 20 cm. The light
will turn off, and the mouse can be used. If not, please try again.
Warranty
This product is guaranteed against any manufacturing defect, based on the
DHLs. February 2, 2002, No 24. In case of failure, please contact the retailer
where you purchased it. You can be found at www.edj.ft
for standards guarantee.
This product complies with the following directives:
- DIRECTIVE 2014/53/UE on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment;
- DIRECTIVE 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
The declaration of conformity for this product is visible on
www.odj.it site, on the product page.
The symbol of the crossed out trash indicates that the product, at the end of
its useful life, must be treated separately from domestic waste and must be
taken to a recycling center for electrical and electronic equipment or
delivered to the seller when buying a replacement. The separate waste
collection contributes in preventing possible adverse effects on the
environment and health and promote the recovery of materials it is made. You
are responsible for assigning the equipment in question at the appropriate
waste disposal center. For more detailed information contact your local waste
disposal service or the shop where it was purchased. Anyone who does not carry
the product in a recycling center for electrical and electronic waste shall be
punished with administrative penalty provided by law on the illegal disposal
of waste.