FEIT Electric FP1X4-840-WH LED Flat Panel Fixture Instruction Manual

FEIT Electric FP1X4-840-WH LED Flat Panel Fixture

The Feit Electric 1X4 LED Flat Panel Fixture is designed to enhance the lighting in your home or office. With a warranty of up to 5 years, the fixture is made with high-quality materials and workmanship. The installation process is easy and can be done with simple tools.

Safety Information

Before installing the fixture, always turn off the power supply at the fuse or circuit breaker box. Wear rubber-soled shoes and work on a sturdy wooden ladder. Ground the fixture to avoid potential electric shocks and ensure reliable starting. Double-check all connections to be sure they are tight and correct. Account for small parts and destroy packing material, as these may be hazardous to children.

Pre-Installation

Tools Required

• Phillips screwdriver
• Power Drill
• 1/2 in. Drill Bit

Hardware Included

Installation

1. Turn OFF the main power at the circuit breaker before installing the fixture.
2. Identify the wiring: black is line voltage, white is neutral, and green is ground.
3. Attach the mounting plate to the ceiling using the 3/16 in. bolts and toggle nuts. Make sure the plate is level and secure.
4. Connect the wires from the fixture to the corresponding wires in the junction box using wire nuts. Make sure all connections are tight and secure.
5. Attach the fixture to the mounting plate using the machine screws #8-32 x 1 in. Make sure the fixture is level and secure.
6. Turn ON the main power at the circuit breaker and test the fixture to make sure it is working properly.

For any questions or concerns about your Feit Electric 1X4 LED Flat Panel Fixture, please contact our Customer Service Team at 1-866-326-BULB (2852) or visit our website at www.Feit.com.

THANK YOU
We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this LED Flat Panel Fixture. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric!

Safety Information

For your safety, always remember to:

• Turn off the power supply at the fuse or circuit breaker box before you install the fixture.
• Ground the fixture to avoid potential electric shocks and to ensure reliable starting.
• Double-check all connections to be sure they are tight and correct.
• Wear rubber soled shoes and work on a sturdy wooden ladder.
• Account for small parts and destroy packing material, as these may be hazardous to children.
• This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.
• WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury unless handled properly.
• CAUTION: Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
• NOTICE: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
• Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.

Pre-Installation

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Installation

Identifying the Wires

• Turn OFF the main power at the circuit breaker before installing the fixture.
• Identify the wiring: (black-line voltage, white – neutral and green-ground)

Attaching the Mounting Plate

• Attach the mounting plate (BB) to the junction box using the two #8-32 x 1 in. screws (EE) provided.
• Align the mounting plate in the direction you want the fixture to be aligned. Once the toggle bolts are installed, you cannot change the orientation.

Positioning the Toggle Bolts

• Using the mounting plate (BB) as a guide, mark the position of the holes on the ceiling or wall where the toggle bolts will be placed.

Installing the Toggle Bolts

• Remove the mounting plate (BB) from the junction box.
• Drill four holes where marked using a 1/2 in. drill bit.
• Insert a screw (CC) through the front of the mounting plate (BB) and reattach the toggle nut to the screw (CC). Repeat for all four toggle bolts.

Re-attaching the Mounting Plate

• Feed the junction box wires through the center of the mounting bracket plate (BB) hole.
• Re-attach the mounting plate (BB) by inserting the four toggle nuts (CC) into the drilled holes.
• Once the toggle nuts (CC) are through and expanded, pull the screw (CC) downward to engage and tighten.
• CAUTION: When installing the panel on a vertical surface, the mounting plate must be installed in such a way that the mount-ing tabs are oriented in a vertical position. If the mounting tabs are not in this position the fixture will not be properly secured and could fall resulting in serious injury.

Connecting the Panel Light

• Hook the support wire from the fixture on the mounting bracket plate.
• CAUTION: Care must be taken not to have excess wires outside the junction box to avoid pinching wires. This may cause a short and could lead to a potential hazard.

Installing the Panel Light

• Connect the three wires coming from the fixture to the junction box wires (black – line voltage, white -neutral and green – ground).

Connecting the Swing Arms

• Insert the swing arm’s key hole slot into the mounting bracket plate’s hanging screw.

Attaching the Panel Light

• Feed the junction box and fixture wires through the mounting bracket plate’s center hole.
• Raise the fixture to the direction of the arrow on the swing arm.

Securing the Panel Light

• Once the fixture has been raised and is flush to the ceiling, lock the fixture by moving it towards the opposite direction it was raised (as indicated on the product label).
• FEIT.COM

FCC STATEMENT

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Feit Electric Company, 4901 Gregg Road, Pico Rivera, CA 90660. www.feit.com.

Warranty

LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials for up to 5 years from the date of purchase. If it fails to do so, please contact the Customer Service Team at 1-866-326-BULB (2852) or visit www.Feit.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>