Marshall CV6XX-HFH Compact Weatherproof Dome Housing for PTZ Camera User Manual

Marshall CV6XX-HFH Compact Weatherproof Dome Housing for PTZ Camera

Product Information

The CV6XX-HFH is a weatherproof dome housing for PTZ cameras. It can be used in both indoor and outdoor environments, providing protection against harsh weather conditions. The housing is designed to accommodate PTZ cameras and comes with electrical conduit guidelines for proper installation. The housing is available in two input power configurations: (1) 24 VAC/VDC and (2) 110-220 VAC. The product comes with a 1-year warranty.

Product Usage Instructions

1. Read the instructions: Before operating the unit, read all safety and operating instructions.
2. Retain instructions: Keep the safety and operating instructions for future reference.
3. Heed warnings: Adhere to all warnings on the unit and in the operating instructions.
4. Follow instructions: Follow all operating and user instructions for proper use of the product.
5. Electrical connections: Only a qualified electrician should make electrical connections.
6. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Cable runs: All cable runs must be within permissible distance.
8. Mounting: The unit must be properly and securely mounted to a supporting structure capable of sustaining its weight. Installation should be made by a qualified installer and in compliance with local codes. Care should be exercised in selecting suitable hardware for installation of the unit, taking into account both the composition of the mounting surface and the weight of the unit. Periodically examine the unit and the supporting structure to ensure proper installation.
9. Service: If the unit is defective and falls within the 1 year warranty, contact Marshall Electronics Inc. 800-800-6608 for return authorization and shipping instructions.
10. Unpacking: Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. Save both the shipping carton and packaging material for future shipments of the equipment. Keep these installation and operating instructions.

PRODUCT INSTRUCTIONS

PRECAUTIONS – WARNINGS – ADDITIONAL INFORMATION

1. Read Instructions – All the safety and operating instructions should be read before the unit is operated.
2. Retain Instructions -The safety and operating instructions should be retained for future reference.
3. Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to.
4. Follow Instructions -All operating & user instructions should be followed.
5. Electrical Connections – Only a qualified electrician should make electrical connections.
6. Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards
7. Cable Runs – All cable runs must be within permissible distance
8. Mounting -This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight of the unit. Accordingly:
9. Installation should be made by a qualified installer.
10. Installation should be in compliance with local codes
11. Care should be exercised to select suitable hardware to install the unit, taking into account both the composition of the mounting surface and the weight of the unit. Be sure to periodically examine the unit and the supporting structure to make sure that the integrity of the installation is intact. Failure to comply with the foregoing could result in the unit separating from the support structure and falling, with resultant damages or injury to anyone or anything struck by the failing unit

SERVICE
If the unit is defective and falls within the 1 year warranty, customer should contact Marshall Electronics Inc. 800-800-6608 for return authorization & shipping instructions

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE

The lightning flash with an arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance

UNPACKING

Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. Be sure to save

• The shipping carton and packaging material. They are the safest material in which to make future shipments of equipment.
• These Installation and Operating Instructions

For technical questions or product returns – call Marshall Electronics Inc. Customer Service (800-800- 6608)

• The External Nut on All electrical wire feed Glands must be tightened to create a weather-tight seal prior to putting CV6XX-HFH in service. Failure to create this seal may result in water incursion into the enclosure. This may lead to electrical shock, product failure, and damage to electrical systems installed within the enclosure, including but not limited to damage to the camera, heater and blower circuitry, cooling circuitry, and other systems installed in the unit.
• All screws on the hinged lower must be tightened to create seal on the enclosure. Failure to create this seal may result in water incursion into the enclosure. This may lead to electrical shock, failure and damage to electrical systems installed within the enclosure, including but not limited to damage to the camera, heater and blower circuitry, cooling circuitry, and other systems installed in unit.
• Do not over-tighten any Screws, Stand Offs, or other fasteners on this unit. Failure to heed this warning will cause damage or failure of the CV6XX-HFH enclosure.
• Be sure to take extra care to Protect the Lens of the unit prior to and during installation, and during service. The suspension packaging box is a handy platform to protect lens and enclosure while installing the camera and accessory electronics before installation. Failure to protect lens will adversely affect product perform

Hardware Pack Provided with CV6XX-HFH Housing

Stand Off Height Assembly Table for Camera Height Adjustment

MVP Voltage Matrix

Enclosure Input – Camera Output

Input Voltage to Enclosure
The MVP Enclosures can be powered by Inputs of either High Voltage 110-220 VAC. Or Low Volt 24 VAC/ VDC

Voltage Matrix for Input / Output

Output Voltage to Power Camera
MVP provides step-down voltage to supply camera power for 12VDC and 24V Cameras. 24V Camera Supply 24V output depends on Site Power Input, for either 24V Direct Current or Alternating Current (see table above)

Input Power Configuration for 24 VACI VDC

The MVP comes ready for 110-220VAC Input power
To use 24 VAC/VDC you must take a moment to allow input configuration for Low Voltage Input USE Blue24 VAC Bypass Cable to hook up power inside CV6XX-HFH

Input Power Configuration for 110- 220 VAC

Input Specifications

• Input Voltage: 90-264 VAC, (127-370 VDC)
• Frequency Range: 47-63 HZ
• Input CurrentFull Load(Typ.): 1.8A@115VAC, 1.0A@230VAC
• Recommended Min. Circuit Breaker: 6 A (type C)
• Int. Electrical. Working Temp: -20~+70C
• MTBF: 353.6Khrs min. MIL-HDBK-217F(25C)

Camera Power Output Power for MVP

Camera Power Setup (STANDARD 12VDC CONNECTOR)

All CV6XX-HFH environmental enclosures come standard with a 12VDC Right Angle Barrel Plug (3.3mmx 5.5mm with an imm center pin) for a majority of the P cameras on the market.

If your IP camera’s power connector is different but still accepts up to 13VDC for power, please see our section on Camera Power Setup {NON-STANDARD CONNECTOR) for instructions on how to power your camera. Below are pictures of typical NON-STANDARD CONNECTORS

If you IP camera’s power requirements are for 24 VAC ONLY, please make sure that the CV6XX-HFH Environmental dome that you purchased is a 24VAC version. Cameras that run on 24VAC will not work with the 12VDC and 110-240 VAC versions of our CV6XX-HFH Environmental domes.

NOTE : The only way the 24VAC camera will ork on our 12VDC and 110-240VAC dome is f you, the customer, to provide a separate pOwer lead into the dome for your camera. We have designed our domes to be simple and efficient when it comes to powering our environmental component and camera. So when comes to cameras with 24VAC power requirements, we RECOMMEND- the 24VAC versions of our Environmental domes for proper installation

Camera Installation

cV6XX-HFH Enclosure mini-domes and PTZ cameras as tall as 9.375 inches in height. Our standoff combination includes supported heights of 0.50″, and 0.74″. 1.00″. 1.25″, 1.50″, 1.75″. 2.00″. 2.2s”, 2.50″. 2.75″. 3.00″, and 3.75″%. These standoff heights can be applied t upper and lower mount locations based on the height of your camera. Most cameras will often utilize a center screw hole for securing the camera onto the plate.

If your camera has other mounting capabilities, the n center the camera on our camera bracket and check to see if it aligns with any of the pre-made holes on the camera bracket. If it does, great you can use the pre-made holes. If it doesn’t, you can mark the holes needed and drill them into the camera plate (steel plate).
For power, all of our CV6XX-HFH Environmental Enclosure Series comes standard with a 12VDC Barrel plug with a center pin. if your camera does not support this, then check our section on Camera Power Setup (NON-STANDARD CONNECTOR) for details.

Installing Camera Bracket

In order to mount the CV612/CV620/Cv630 CAMERA you must install the PTZ cameras included Ceiling Mount (CV620-CM-KIT) This will allow for hole alignment on the CB-1007 V4 MOUNTING PLATE.

1. Install the PTZ camera onto the CV6XX-HFH Camera Bracket with (3) m3-.5, (3) m3 external lock washers, and (3) m3 1/8″ washers that are included.
2. The PTZ camera requires a 2.25″ spacing for optimal fit and operation. Use (1) 1.5″ standoffs and (1).75″ standoffs that are provided to create a 2.25″ standoff You will need to create 4 of these with the included. hardware.
3. The 2.25″ standoffs will be inserted on the upper portion of the CV6XX-HFH
4. Now slide the camera bracket with the camera into place to line up with 4 Screws holes from the standoffs.
5. Use (4) #8-32 screws (Phillips’s head) to secure the bracket into place.

Tip : Insert (2) #8-32 screws in the front two standoffs to provide a guide to slide the camera bracket into. The last two corner holes should line up and be secured last.

The picture represents the camera bracket orientation & how it is secured. Don’t forget to mount your camera to the CV6XX-HFH camera bracket based on the instructions.

Required components (see component checklist): Parts # 1,2,3,5,6,7,& 8

1. Install the PTZ camera onto the CV6XX-HFHCamera Bracket center hole with (1) .25-20 3/8″ Long Bolt, and (1) .25″ Lock Washer that are included.
2. The 2.0″ standoffs will be inserted on the lower lens portion of the CV6XX-HFH
3. The picture represents the standoff location & orientation. The height of standoffs will vary depending on the camera used.
4. Now slide the camera bracket with the camera into place to line up with 4 screws from the standoffs.
5. Secure the plate by using (4) .75″ standoffs to lock the bracket in place. Ihe two front locations will require the use of (2) 25″ washers

Electrical Conduit Guidelines

For optimal performance, your CV6XX-HFH Enclosure is designed to be air & water tight to eliminate any moisture, dust, and t insect damage that can cause performance, reliability, and maintenance-related issues.

Marshall does nat endorse, nor has it evaluated any of these products. Test products first, and follow all manufacturers’ instructions. Follow all applicable electrical and building codes and installation guidelines. The end user assumes liability for the applicability of these products and their effectiveness and incurred liability in using these products.

IMPORTANT
VENT STOPPER PLUGS for CONDUIT
Foam Conduit Fond Pugs tar W” LD Conduit Fittings Conduit Feeds Must Be Sealed for Safe and Satisfactory Product Performance. Conduit Stopper Plugs prevent Humid Air exchange from venting through the external conduit into Marshall sealed enclosure when the conduit is used with Marshall enclosures. Vent Stopper Plugs eliminate conduct-driven condensation in surveillance camera enclosures or other outdoor enclosure products.

Conduit Feeds Must Be Sealed for Safe and Satisfactory Product Performance

Conduit Stopper Plugs prevent Humid Air exchange from venting through the external conduit into Marshall sealed enclosure when the conduit is used with Marshall enclosures. Vent Stopper Plugs eliminate conduit-driven condensation in surveillance camera enclosures or other outdoor enclosure products .

CV6XX-HFH Mounting Detail

Warranty

For Warranty information please refer to Marshall website page:
https://marshall-usa.com/company/warranty.php
20608 Madrona Avenue, Torrance, CA 90503
Tel : 800-800-6608 / 310-333-0606
Fax : 310-333-0688
www.marshall-usa.com
support@marshall-usa.com

References

• USA Location information - USA.com
• Marshall Electronics - Warranty Information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>