PARTS EXPRESS BX-4 Bluetooth Audio Receiver Instruction Manual

PARTS EXPRESS BX-4 Bluetooth Audio Receiver Instruction Manual

GENERAL INTRODUCTION

BX-4 is a Bluetooth® receiver with 5.0 chip. This chip offers high quality sound and makes the compatibility and integral performance more optimizing. Just use 3-pin XLR to connect console or active speaker, then using Bluetooth® to connect smart phone, pad such devices to realize wireless transmission. STEREO-LINK button helps BX-4 pairing with another BX-4 to transmit the signal to audio equipments.

CONNECTION INTRODUCTION

1. USB CHARGE: charging interface supply power to devices.
2. POWER ON/OFF: push switch-turns the BX-4 on and off.
3. PAD 0dB -10dB: sensitivity attenuator, lower the input signal sensitivity and avoid signal overload and distortion.
4. CHARGE: battery indicator,during charging the blue light lits, when battery is already full, the indicator goes out.
5. LED indicator: when turn on the BX-4, the product to be paired, red and blue light lit alternation; when paired successfully, blue light flash slowly. When paired and Bluetooth played music, blue light solidly lit; if no music, blue light flash slowly.
6. STEREO-LINK button: press the button(STEREO-LINK) on both BX-4 for 2 seconds, the blue light flash quickly(on both BX-4 LED indicator flash). Each BX-4 searched for each other, when they are successfully paired, one BX-4 red and blue light lit alternation another BX-4 blue light flash slowly(at that time, the output signal is STEREO).
7. XLR: balanced output connector

SETUP

1. Insert bx-4 to mixer’s XLR input connector.
2. Use 1/4″(6.35mm) cable to connect 1/4″(6.35mm) input connector on active loudspeaker and 1/4″(6.35mm) output connector on mixer.
3. Paired with Bluetooth devices. NOTE: you can connect to mixer, amplifier or other devices that accepts line-level inputs(this device must be powered off). Here take the mixer as an example.

BLUETOOTH PAIRING A SINGLE BX-4

1. Power on your Bluetooth device.

2. Power on BX-4 red and blue light flash alternation.
   

3. Red and blue light flash alternation, to be paired.

4. Navigate to your bluetooth device set up screen, find Alctron BX-4 and connect.
   

5. When paired successfully, blue light flash slowly. When paired and Bluetooth played music blue light solidly lit: if no music , blue light flash slowly.
   

6. Adjust the volume on your Bluetooth device.

STEREO-LINK 2BX-4

1. Press the STEREO-LINK button on both BX-4 for 2 seconds.
   

2. Both STEREO-LINK LED will flash blue light quickly. Then BX-4 will search for each other.
   

3. When they are successfully, one BX-4 red and blue light lit alternation another BX-4 blue light flash slowly
   

4. Following BLUETOOTH PAIRING A SINGLE BX-4 steps to connect with Bluetooth devices.

SPECIFICATION

• Bluetooth version: Bluetooth V5.0
• Power supply: 3.7V lithium battery power supply
• Standby current: <50uA
• Working current: ≥10mA
• Temperature range: -40℃ to +80℃
• Wireless transmission range: 10m
• Sensitivity: -95dBm<±0.1% BER
• Frequency range: 2.4Ghz-2.480Ghz
• Signal to noise: ≥95dB
• Distortion: ≤0.1%
• Charging method: USB charging
• Stand by: 50days(Theoretically)
• Working time: 24hours (Theoretically)
• Net weight: 95g
• Size: 33.427.5124mm

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Caution: Any changes or modi fi cations to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>