Tuya Smart SW03 Smart Wireless Battery Camera User Guide

Tuya Smart SW03 Smart Wireless Battery Camera

Welcome
Thank you for choosing our smart camera. Getting started is easy.

What’s Included

Product Details

The Smart Wireless Battery Camera (Model: SW03) is a security camera that comes with a mounting bracket, USB cable, wall mount screw sets and a quick start guide. It has a lens, microphone, indicator light, light sensor, and PIR.

Connection Preparation

1. Bring the camera and phone within 1 to 3 feet (30 to 100 centimeters) of the router.
2. Make sure your smartphone is connected to your wireless router.
3. The camera only works under 2.4G Wi-Fi and does not support 5G Wi-Fi.

Bring the camera and phone within 1 to 3 feet (30 to 100 centimeters) of the router.

Note:
Make sure smart phone is connected with your wireless router. Please note the camera is only working under 2.4G Wi-Fi, not support 5G Wi-Fi.

Get the APP and Account

1. Download the Tuya smart APP to your smartphone from App Store or Google Play or scan the QR code located in the quick start guide.
2. Launch the app from your smartphone and click the Sign Up button. Follow the on-screen instructions to create a new account.

For the best experience, please download the “Tuya smart” APP to your smartphone from App Store or Google Play, store or you can also scan the QR code below, the APP icon will be displayed after installed successfully.

Launch the app from your smartphone and click the Sign Up button. Follow the on-screen instructions.

Insert Micro SD Card

Insert the Micro SD card gently on the side edge of the camera.

Connect Power to the Camera

Connect the power to the camera using a Micro USB Power Adapter (DC 5V/2A).

Set up Your Camera

1. Press and hold the Reset button for above 5 seconds until the blue LED blinks.
2. The red LED will turn on when the system is starting up.
3. The red LED will blink quickly when it’s in standby mode for configuration.
4. The blue LED will blink quickly when the network pairing is in progress.
5. The blue LED will turn on when the camera is online.
6. The red and blue LED will blink alternately during OTA upgrade.
7. Press the Reset button for above 5 seconds, then release the button to reset the camera, then the LED light will blink quickly.
8. Click “Add Device” or “+” on the right corner to add device; Then click” Security&Sensor” to select” Smart Camera”
9. Follow the App’s instructions and input the right wifi password; Point the QR code to the camera lens for 15-20cm ; Click”HEARD THE BEEP” when you heard “dingding”. After processing,it will pair successfully.
10. The blue light is on, camera is ready for viewing.

Mount Your Camera

You can place your camera on a shelf or other flat surface, or you can mount it to the wall. To mount the camera to the wall, follow these steps:

1. Fasten the mounting screw into the wall.
2. Mount the camera from the screw.
3. If you’re mounting the camera to drywall, use the plastic drywall anchors provided.

To mount your camera to the wall:

• Fasten the mounting screw into the wall, and then mount the camera from the screw.
• If you’re mounting the camera to drywall, be sure the plastic drywall anchors that are provided.

You’re done!

Congratulations!
Your camera is set up and ready to go.

Appendix Camera LED Guide

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipmemt does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

All trademarks are used for reference purposes only. Thanks again for choosing our smart camera! Make life safe in your hands! Boost security mobility in your smartphone!

Date of FCC Statement: 2023.02.07.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>