Makeblock LV V1.0 D1.2.5 mBot Neo STEM Education Coding Robot Kit Instruction Manual

Makeblock LV V1.0 D1.2.5 mBot Neo STEM Education Coding Robot Kit

Product Information

The Explorer Kit is a DIY robotics kit that allows users to build their own robot using the provided components. The kit includes an LED matrix, motors, wheels, a screwdriver, screws, a battery holder, a USB connector, and various other components. The robot can be controlled manually or through an interface with a lithium battery.

Product Usage Instructions

1. Begin by referring to the assembling manual in the language of your choice (English, French, Spanish, Portuguese, German, Russian,Italian, or Latvian).
2. Use the included screws and screwdriver to assemble the components including LED matrix, motors, and wheels according to the instructions.
3. Insert AA batteries into the battery holder (not included).
4. Connect the battery holder interface to the AA battery holder.
5. Connect the motor interface to the motors.
6. Connect the USB connector to the robot.
7. To control the robot manually, switch to manual control mode by pressing button 1.
8. Use buttons 2 and 3 to control movement and button 4 to change the speed of the motors.
9. To switch to drive mode, press button 5.
10. In drive mode, you can control the robot using an interface with a lithium battery.
11. Refer to the FCC radiation exposure statement and IC statement regarding safe use of the equipment.

Note: Do not forget to refer to the assembling manual for detailed instructions on building the robot. Also, ensure that you have all necessary components before beginning assembly.

Parts List

• Mainboard mCore
• Chassis
• Ultrasonic Sensor
• Line-follower Sensor
• LED Matrix
• Motor
• Mini Wheel
• Wheel
• Screwdriver
• RJ25 Cable
• USB Cablel
• Bracket 33120°
• M4*25mm Brass Stud
• M4*16mm Brass Stud
• M3*25mm Screw
• M4*14mm Screw
• M2.2*9mm Self-drilling Screw
• M3 Nut
• M4 Nut
• Plastic Spacer 4710
• Plastic Spacer 473
• Plastic Rivet
• AA Battery Holder
• Line-follower Map
• M4*8mm Screw
• Velcro sticker pad
• Infrared Remote Controller
• Mini Screwdriver

Use of Screwdriver

Mainboard mCore Introduction

• 1. AA Battery Holder Interface
• 2. 3.7V Lithium Battery Interface
• 3. Reset
• 4. Power Switch
• 5. USB Connector
• 6. Motor Interface
• 7.8. RJ25 Port
• 9.10. RGB LED
• 11. Buzzer
• 12. Button
• 13. Infrared Receiver
• 14. Light Sensor
• 15. Infrared Transmitter

Infrared Remote Controller

Buttons instructions

1. Obstacle avoidance mode
2. Manual control mode
3. Line-following mode
4. Move forward
5. Turn left
6. Turn right
7. Move backward
8. Speed level dial

Battery Installation Guide

1. Keep pressing
2. Pull the battery case

Building Instructions

Wiring

1. Motor (Right）
2. Motor (Left)

• Now that you have built the robot, open the Quick Start Guide and start coding!

More Shapes

For more information, please visit: https://www.makeblock.com/

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference.
2. this device must accept any interference, including interference that may cause undesired operation of the device.

DECLARATION OF CONFORMITY

Declaration of conformity: Hereby, Makeblock Co., Ltd., declares that this product is in compliance with the essential requirements and other relevant provisions of Directive RED 2014/53/EU and the RoHS directive 2011/65/EU.

WARNING

• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Different types of batteries or new and used batteries are not tobe mixed.
• Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instruction.
• This product contains a Button or Coin Cell Battery. A swallowed Button or Coin Cell Battery can cause internal chemical burns in as little as two hours and lead to death. Dispose of used batteries immediately. Keep new and used batteries away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Makeblock Co., Ltd.

• Address: 4th Floor, Building C3, Nanshan iPark, No.1001 Xueyuan Avenue, Nanshan District, Shenzhen, Guangdong Province, China
• Technical support: support@makeblock.com
• www.makeblock.com

D1.2.5_KD010165000

References

• Robot Kits & STEM Toys for K-12 Schools and Home Education｜Makeblock
• Robot Kits & STEM Toys for K-12 Schools and Home Education｜Makeblock

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>