VENTS D Series Wall and Ceiling Mounted Axial Fan User Manual
- June 10, 2024
- VENTS
Table of Contents
VENTS D Series Wall and Ceiling Mounted Axial Fan
AXIAL FANS
user’s manual
WARNING
Disconnect the fan from power mains prior to any connection, servicing and repair operations. Mounting and maintenance are allowed for duly qualified electricians with valid electrical work permit for electric operations at the units up to 1000 V after careful study of the present user’s manual. The single-phase power mains must comply with the acting local electrical norms and standards.
The fixed electrical wiring must be equipped with an automatic circuit breaker. The fan must be connected to power mains through an automatic circuit breaker QF integrated into the fixed wiring system with the gap between the breaker contacts on all poles not less than 3 mm.
Check the fan for any visible damages of the impeller and the casing before
starting installation. The casing internals must be free of any foreign
objects which can damage the impeller blades. Misuse of the device or any
unauthorized modification is not allowed.
The fan is not to be used by children and persons with reduced physical,
mental or sensory capacities, without proper practical experience or
expertise, unless they are controlled or instructed on the product operation
by the person(s) responsible for their safety.
Do not leave children unattended and do not let them play with the product.
Take steps to prevent ingress of smoke, carbon monoxide and other combustion
products into the room through open chimney flues or other fire-protection
devices. Sufficient air supply must be provided for proper combustion and
exhaust of gases through the chimney of fuel burning equipment to prevent back
drafting.
Transporting medium must not contain any dust or other solid impurities, sticky substances or fibrous materials.
Do not use the fan in the environment containing hazardous or explosive materials and vapours, i.e. spirits, gasoline, insecticides, etc.
Do not close or block the fan intake or extract vents in order to ensure the most effective air passage.
Do not sit on the fan and do not put objects on the fan.
Fulfill the requirements stated in this user’s manual to ensure long service
life of the product.
Recycle at the end of the service life.
Do not dispose the product with unsorted municipal trash.
FAN DESIGNATION KEY
Designation key example:
VENTS 125 DVT K fan with 125 mm exhaust spigot diameter, D-series, supplied
with a pull-cord switch, timer, back valve.
Read the present user manual carefully before proceeding with installation
works.
Compliance with the manual requirements ensures reliable operation and long
service life of the product. Keep the user’s manual available as long as
you use the product. You may need to re-read the information on the
product servicing.
DELIVERY SET
The delivery set:
1. Fan – 1 item;
2. Screws and dowels – 4 items;
3. Plastic screwdriver – 1 item (only for the models with a timer);
4. User manual – 1 item;
5. Packing box.
SHORT DESCRPTION
The product described herein is an axial fan for exhaust ventilation of small
and medium-sized products.
The fan is made of white plastic.
The fan may include a back valve to prevent air back drafting when the fan
does not run.
The fan is designed for connection to Ø 100, 125 and 150 mm air ducts.
Due to constant improvements the design of some models may slightly differ
from those ones described in this manual.
OPERATION RULES
The fan is designed for connection to AC 220-240 V, 50 Hz power mains.
The model 12 is designed for connection to 12 V, 50 Hz power mains directly or
to AC 220-240 V, 50 Hz power mains through the step-down transformer, for
example, TRF 220/12-25 (optional).
Air flow direction in the system must match the pointer direction on the fan casing.
Ingress protection rating against access to hazardous parts and water ingress:
IP24 – X, X1, Xstar series IP34 – D, D1, S, S1, LD, LD1, LD light, LD Fresh
time, Cosmo, Modern, Techno, Domino The fan is rated for operation at the
ambient temperature ranging from +1°C up to +45°C. The fan requires no
grounding.
MOUNTING
The fan is designed for ceiling or wall mounting and is connected to a ventilation shaft or an air duct of respective diameter, fig. 1.
Fan mounting sequence:
Step 1 – Cut of power supply and make preparations in a room to install a fan
following step 1.1-1.2;
Step 2 – Remove the front plate from the fan following step 2.1-2.7 depending
on a fan model;
Step 3 – mark and drill the holes for the fan fasteners and fix the fan, step
3.1 – 3.3;
Step 4 – connect the fan to power mains and adjust the timer and humidity
sensor set point if required following steps 4.1-4.7 depending on the fan
model);
Step 5 – cover the fan casing with a front plate following step 5.1-5.7
depending on the fan model;
Step 6 – supply power to the fan following step 6.1.
For LD Freshtime model: install AA 1.5 V battery following step 5.7 and set
current time, step 5.7.
The battery (AA 1.5 V) is not included into delivery set.
TERMINAL DESIGNATION KEYS AT WIRING DIAGRAMS:
L – phase (only for 220-240 V power mains);
N – 0 (only for 220-240 V power mains);
LT – timer control line;
QF – circuit breaker;
S – external switch;
S1 – external fan switch;
S2 – external light switch.
Warning! The timer circuit is under mains voltage. Disconnect the fan
from power mains prior to any adjustment operations. The fan delivery set
includes a specially designed plastic screwdriver for fan settings
adjustments.
Use the screwdriver to change the turn-off delay time or the humidity set
point, see step 4.7.
ATTENTION! The fan rated for 12 V power mains (marked on the fan casing) connect to 12 V power mains only!
ELECTRONICS OPERATING LOGIC
The fan with the timer T – the fan starts after the external switch, e.g. the light switch, supplies control voltage to the input terminal LT (ST). After the control voltage is off, the fan continues operating within the set time period adjustable from 2 to 30 minutes by the timer. The VT model is turned on and off by the pull-cord switch.
The fan with the timer T1 – the turn-on delay timer is activated after
the external switch, e.g. the light switch, supplies control voltage to the
input terminal LT (ST). The fan starts only after the turn-on delay timer
countdown. The turn-on delay time is adjusted in two ranges from 10 seconds to
90 seconds and from 2 minutes to 30 minutes. After the control voltage is off,
the fan operates within the time period set with the timer from 2 to 30
minutes. The adjustment range is selected with a jumper on the timer circuit
board.
The fan with the timer and the humidity sensor TH – the fan starts after the
external switch, e.g. the light switch, supplies control voltage to the input
terminal LT (ST) or if indoor humidity level H exceeds the set point
adjustable from 60% to 90%. After the control voltage is off, the fan operates
within the time period set with the timer from 2 to 30 minutes. To set the
maximum humidity set point turn the potentiometer control knob to H max (90%)
position.
To adjust the turn-on delay time turn the control knob of potentiometer T
clockwise to increase the set point and counterclockwise to decrease it.
To adjust the humidity set point turn the control knob of H potentiometer
clockwise to increase the humidity sensor threshold and counterclockwise to
decrease it.
Warning! The timer circuit is under mains voltage. Disconnect the fan from power mains prior to any adjustment operations. The fan delivery set includes a specially designed plastic screwdriver for fan settings adjustments. Use the screwdriver to change the turn-off delay time or the humidity set point, see step 4.7. Do not use a metal screwdriver, knife, etc. for adjustment operations not to damage the circuit board.
MAINTENANCE
The product surfaces must be regularly cleaned from dirt and dust. Cut off
power supply prior to any maintenance operations, see step 1.1. Remove the
front cover following step 2.1-2.7 depending on a model type), clean the fan
as in fig. 2 and cover the fan following step 5.1-5.7 depending on a model.
Connect the fan to power supply, step 6.1. For cleaning use a soft cloth or
brush and mild detergent water solution.
Avoid water dripping on the electric components. Wipe the surfaces dry after
cleaning.
STORAGE REGULATIONS
Transport the product by any transportation vehicle in the manufacturer’s
original package.
Store the delivered product in the manufacturer’s original packing box in a
dry ventilated premise with the temperature range from +50C up to + 400C and
relative humidity less than 80%. The storage environment must not contain
dust, acid or alkali vapours that may cause corrosion of the product parts.
MANUFACTURER’S WARRANTY
The fan is manufactured at the factory of “Ventilation systems” PrJSC (hereinafter referred to as the Manufacturer).
By purchasing this product the customer confirms to have read and agreed to
the terms, rules and requirements related to operation, storage,
transportation, mounting, adjustment, connection, maintenance and repair as
well as warranty obligations with respect to this product as set forth in the
manufacturer’s accompanying documentation to the product.
The manufacturing company sets forth the warranty period (service life) of the
product as 60 months following the sale date via retail network subject to the
customer’s ensuring compliance with the rules of transportation, storage,
mounting and operation of the product. In case of any malfunction of the
product through the fault of the Manufacturing company within the warranty
period (service life), the customer shall have the right to elimination of the
manufacturing defects by means of warranty servicing performed free of charge.
The warranty servicing implies performance of activities related to elimination of defects in the product aimed to provide intended use of the product by the customer. The defects are eliminated either by replacing or repairing such a product or a part (component) thereof.
NOTE: with the purpose of performing warranty servicing you please produce User Manual or other relevant substituting document and the payment document as an evidence of the purchase with indication of the sale date. The product model shall comply with that one specified in the User Manual or other relevant substituting document.
With the purpose of performing warranty servicing please contact the trade company where you purchased the product. If warranty servicing on the spot proves impossible, you will be provided with the necessary information regarding rendering of this service.
Manufacturer’s warranty shall not apply in the following cases:
– in case the customer fails to provide the product in complete according to
the package contents specified in the User Manual or other relevant
substituting document, including any components disassembled by the customer;
– in case of incompliance of the model or marking of the product with data
specified on the product packaging and in the User Manual or other relevant
substituting document;
– in case of non-timely technical maintenance of the product by the customer
(dust, mud, oil condensate, foreign particles);
– in case of causing external damage to the product by the customer (‘damage’
shall not apply to external changes of the product required for the product
mounting);
– in case of altering the product design or further reworking of the product;
– in case of replacing and using parts, units and components of the product
not prescribed by the manufacturing company;
– in case of other use of the product other than intended use;
– in case of the customer’s violating product operation rules;
– in case of connecting the product to electric mains of voltage exceeding
voltage value specified in the user’s manual;
– in case of step voltage that resulted in the product failure;
– in case of the customer’s performing unauthorised repair of the product;
– in case of performing repair of the product by third persons unauthorized by
the manufacturing company;
– in case of warranty period (service life) expiry;
– in case of the customer’s violating transportation rules assuring prevention
of damaging and/or destruction of the product;
– in case of the customer’s violating product storage rules;
– in case of performing unlawful actions by third persons with respect to the
product;
– in case of force majeure (fire, flood, earthquake, war, hostilities of any
kind, blockade);
– in case of absent seals, provided such seals are prescribed by the User
Manual or other relevant substituting document;
– in case of unavailable warranty card;
– in case of unavailable payment document to confirm the purchase with
indication of the sale date.
The manufacturing company shall be responsible for defects arising through its fault prior to the moment of transferring the product to the ownership of the customer. The manufacturing company shall not be responsible for defects arising after transferring the product to the customer and caused by the customer’s violating the rules of transportation, storage, assembly and operation of the product, or by actions of third persons, an accident or force majeure circumstances.
The manufacturing company shall not be responsible for damage to health and property of the customer caused by the customer’s violating the User Manual or other relevant substituting document; other use of the product by the customer other than its intended use, or by failure of the customer to comply with warnings and other information on the product specified in the User Manual or other relevant substituting document, or by the customer’s violating the rules of transportation, storage, mounting, maintenance and operation of the product.
The fan device is ready for operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>