Harman Kardon Citation Surround Instructions

Harman Kardon Citation Surround

Citation Surround

The Citation Surround is a wireless speaker designed to provide surround sound experience with the Citation Bar. It comes with a wall mount bracket and power cord, which varies depending on the country.

Product Tour

The Citation Surround comes with the following items:

• Wall mount bracket x2
• Citation Surround x2
• Regional power cord x2 (varies depending on country)

The Citation Surround has an LED Indicator Status, which indicates the following:

• Enter into pairing mode
• Wireless connected with Citation Bar
• Out of range/Lost wireless connection

The LED behavior can be flashing for 10 seconds or off. The bottom of the speaker has a reset button, which can be pressed for more than 5 seconds to reset the speaker.

Get Started

To set up the Citation Surround, follow these steps:

1. Place the Citation Bar in the desired location.
2. Connect the power connector of Citation Surround to the power source.
3. Select Speaker Setup on the Citation Bar and follow the on-screen instructions to connect the Citation Surround wirelessly.

Wall Mount

To mount the Citation Surround on the wall, follow these steps:

1. Remove the rubber feet from the bottom of the speaker.
2. Mount the wall bracket on the wall using screws.
3. Feed the power cord upward through the wall mount and connect it to the power connector.
4. Place the speaker in the wall mount with the supplied screws on the bottom.
5. Use the nut at the bottom of the wall mount bracket to angle the speaker and tighten it.

Owner’s Manual

The owner’s manual provides additional information on how to use the Citation Surround. It includes troubleshooting tips, safety information, and warranty details.

Specification

The Citation Surround has the following specifications:

• Wireless connectivity: Wi-Fi and Bluetooth
• Dimensions (W x H x D): 125 x 175 x 125 mm
• Weight: 1.30 kg
• Power supply: 100-240V~,50/60Hz,0.5A
• Power consumption: <2.0W (Standby)

OVERVIEW

LED Indicator Status (for pairing): LED Behavior

• Enter into pairing mode : Flashing
• Wireless connected with Citation Bar : 10 sec→ Off
• Out of range/Lost wireless connection : Flashing

INSTRUCTION

INSTLLATION

• Step 1: Remove the rubber feet from the bottom of the speaker.
• Step 2: Mount the wall bracket in the wall using screws.
• Step 3: Feed the power cord upward  through the wall mount and connect to the power connector.
• Step 4: Place the speaker in the wall mount with the supplied screws on the bottom.
• Step 5: Use the nut at bottom of wall mount bracket to angle the speaker and tighten.

OWNER’S MANUAL
Download the full Owner’s Manual from harmankardon.com

 PRODUCT SPECIFICATION

• Model Name: CITATION SURROUND
• Signal-to-noise ratio: >80dB
• Output power: 2x50W RMS
• Power Supply: 100-240V ~ 50/60Hz
• Power consumption in sleep mode: <2.0Watts
• 5G WISA transmitter power: <14dBm
• 5G WISA modulation: OFDM, BPSK, QPSK, 16QAM
• 5G WISA transmitter frequency range: 5.15 – 5.35GHz, 5.470 – 5.725GHz, 5.725 – 5.825GHz
• Dimension (W x H x D): 105 x 273 x 86mm (4” x 10.7” x 3.3”)
• Weight: 1.29kg (2.84 lb)
• Packaging Dimension (W x H x D): 235 x 383 x 150mm (10” x 15” x 6”)
• Packaging Weight (Gross): 3.57kg (7.87 lb)

Note: This product is designed to be instantly on and ready to receive signal from WiSA Tx Unit at a moment’s notice, wireless connection must remain active at all times to ensure proper operation.
The product is in compliance with the European Union energy legislation. The product will enter into sleep mode (networked standby) after 20 minutes without operation, after which it can be re-activated via wireless.

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B) / NMB-3 (B).

IC Caution:
User should also be advised that:

1. the device for operation in the band 5150 – 5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2. the maximum antenna gain permitted for devices in the bands 5250 – 5350 MHz and 5470 – 5725 MHz shall comply with the e.i.r.p. limit: and
3. the maximum antenna gain permitted for devices in the band 5725 – 5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
4. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250 – 5350 MHz and 5650 – 5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. No configuration controls are provided for this wireless equipment allowing any change in the frequency of operations outside the FCC grant of authorization for US operation according to Part 15.407 of the FCC rules.

FCC/IC Radiation Exposure Statement:
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Use Restriction: This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range in following countries:

Belgium (BE), Greece (EL), Lithuania (LT), Portugal (PT), Bulgaria (BG), Spain (ES), Luxembourg (LU), Romania (RO), Czech Republic (CZ), France (FR), Hungary (HU), Slovenia (SI), Denmark (DK), Croatia (HR), Malta (MT), Slovakia (SK), Germany (DE), Italy (IT), Netherlands (NL), Finland (FI), Estonia (EE), Cyprus (CY), Austria (AT), Sweden (SE), Ireland (IE), Latvia (LV), Poland (PL) and United Kingdom (UK).
This product contains open source software. For your convenience, the source code and relevant build instruction for software licensed under the GPL is available at http://www.harmankardon.com/opensource. You may also obtain this information by contacting us at OpenSourceSupport@Harman.com

References

• German market leader for CRM in SMEs - CAS Software
• Harman Kardon
• Anatel — Agência Nacional de Telecomunicações
• Microsoft Cortana SDK for Harman Open Source Components

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>