WISeNeT QND-6073R Network Camera User Manual

June 9, 2024
WISeNeT

QND-6073R Network Camera

Product Information: Network Camera

The Network Camera is a high-performance camera designed to
capture high-quality images and videos. It comes in three models:
QND-6073R/QND-6083R, QNO-6073R/QNO-6083R, and QNV-6073R/QNV-6083R.
Each of these models is registered trademarks of their respective
companies.

This camera has important safety instructions that must be
followed for proper usage. The user manual should be read and kept
for future reference. All warnings must be heeded, and all
instructions must be followed to ensure safe operation of the
camera.

The camera should not be used near water or heat sources, and
the ventilation openings should not be blocked. Only use
attachments/accessories specified by the manufacturer. This camera
is intended to be supplied by isolation power, and excessive force
should not be used during installation.

To prevent personal information theft and damage, it is
recommended to change the password every three months. Users are
responsible for managing their passwords and ensuring security.

Product Usage Instructions:

  1. Read the user manual and safety instructions carefully before
    using the camera.

  2. Choose an appropriate location for installation. Avoid placing
    the camera near water, heat sources, or in direct sunlight.

  3. Connect the camera to a power source as specified in the user
    manual. Make sure to use only listed power supply units marked
    Class2 or LPS and rated from 12Vdc, 0.55A or PoE(48V), 0.16A.

  4. Connect the camera to a network using an Ethernet cable or
    wireless connection as specified in the user manual.

  5. Configure the camera settings as desired using the provided
    software or web interface. This may include setting up motion
    detection, recording schedules, and adjusting image quality
    settings.

  6. Monitor the camera feed using the provided software or web
    interface. The camera may also have mobile app support for remote
    viewing.

  7. If the camera is not functioning properly, refer to the user
    manual for troubleshooting tips. If the issue persists, contact
    qualified service personnel for assistance.

Following these usage instructions will ensure proper operation
of the Network Camera and help prevent damage or personal
information theft.

NETWORK CAMERA
User Manual
QND-6073R/QND-6083R QNO-6073R/QNO-6083R QNV-6073R/QNV-6083R

Network Camera User Manual
Copyright ©2019 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
Disclaimer Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the right to change the contents of this document without prior notice. Design and specifications are subject to change without prior notice. The initial administrator ID is”admin”and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. This product is intended to be a Listed Power Supply Unit marked “Class2” or “LPS” and rated from 12Vdc, 0.55A or PoE(48V), 0.16A. (QND-6073R/6083R, QNV-6073R/6083R)
16. This product is intended to be a Listed Power Supply Unit marked “Class2” or “LPS” and rated from 12Vdc, 0.55A or PoE(48V), 0.16A. (QNO-6073R/6083R)
17. This product is intended to be supplied by isolation power.
18. If you use excessive force when installing the product, the camera may be damaged and malfunction. If you forcibly install the product using non- compliant tools, the product may be damaged.
19. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.
20. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.
21. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

22. Installing or using the product in water can cause serious damage to the product. 23. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the
video.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.
CAUTION CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
English _3

OVERVIEW

overview
Class construction
An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION
IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS. These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Please use the input power with just one camera and other devices must not be connected. The ITE is to be connected only to PoE networks without routing to the outside plant. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1. Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.
4_ overview

Please read the following recommended safety precautions carefully. y Do not place this apparatus on an uneven surface. y Do not install on a surface where it is exposed to direct sunlight, near heating equipment or
heavy cold area. y Do not place this apparatus near conductive material. y Do not attempt to service this apparatus yourself. y Do not place a glass of water on the product. y Do not install near any magnetic sources. y Do not block any ventilation openings. y Do not place heavy items on the product. y Please wear protective gloves when installing/removing the camera.
The high temperature of the product surface may cause a burn.
User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below. y Reference : In case of providing information for helping of product’s usages y Notice : If there’s any possibility to occur any damages for the goods and human caused by
not following the instruction Please read this manual for the safety before using of goods and keep it in the safe place.
In particular installation environments, there might be interference in radio communications. When interference of electromagnetic waves occurs between the product and radio communication device, it is recommended to keep a certain distance between the two or change the direction of the receiving antenna.
WARNING
To Prevent damage which may caused by IR LED, don’t stare at operating lamp. For below models only.
QND-6073R/QND-6083R QNO-6073R/QNO-6083R QNV-6073R/QNV-6083R
Risk Group 1
WARNING IR emitted from this product. Do not stare at operating lamp.
Product tested against IEC 62471

CONTENTS

OVERVIEW
3

3 Important Safety Instructions 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC
Memory Card Specifications 6 NAS recommended specs 7 What’s Included 8 At a Glance (QND-6073R/QND-6083R) 10 At a Glance (QNO-6073R/QNO-6083R) 12 At a Glance (QNV-6073R/QNV-6083R)

INSTALLATION & CONNECTION
14

14 Installation (QND-6073R/QND-6083R) 15 Installation (QNO-6073R/QNO-6083R) 16 Installation (QNV-6073R/QNV-6083R) 19 Inserting/Removing a Micro SD Memory
Card 21 Powering and networking

NETWORK CONNECTION AND SETUP
25

25 Connecting the Camera Directly to Local Area Networking
25 Connecting the Camera Directly to a DHCP Based DSL/Cable Modem
26 Using Device Manager 26 Automatically searching camera 26 Configuring IP address 27 Manually registering camera 27 Automatically configuring IP 28 Port Range Forward (Port Mapping) Setup 29 Connecting to the Camera from a Shared
Local PC 29 Connecting to the Camera from a Remote
PC via the Internet

WEB VIEWER
30

30 Connecting to the Camera 31 Password setting 31 Login 31 Camera Web Viewer Setup

APPENDIX
32

32 Troubleshooting 33 Open Source Announcement

English _5

OVERVIEW

overview
RECOMMENDED PC SPECIFICATIONS
· CPU : Intel(R) Core(TM) i7 3.4 GHz or higher · RAM : 8G or higher · Supported OS : Windows 7, 8.1, 10, Mac OS X 10.12, 10.13, 10.14 · Recommended browser : Google Chrome · Supported browsers : MS Explore11, MS Edge, Mozilla Firefox(Window 64bit only),
Apple Safari(Mac OS X only) · VGA : PCIe 256MB GDDR3 video graphics card or higher
RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS
· Recommended capacity : 16GB ~ 128GB(MLC type) · Recommended Manufacturers : SanDisk, Transcend · Product Type : High endurance · The compatibility varies depending on the card manufacturers and types.

NAS RECOMMENDED SPECS

· Recommended capacity : 200GB or higher is recommended. · Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses. · For this camera, you are recommended to use a NAS with the following manufacturer’s specs.

Recommended products QNAP NAS
Synology NAS

Available sizes A maximum of 16 cameras can access simultaneously. A maximum of 16 cameras can access simultaneously.

J When you use Netgear’s NAS equipment, do not allocate the capacity for use. If you use NAS equipment for purposes other than video saving, the number of accessible cameras may be reduced.

6_ overview

OVERVIEW
CRoAaf tUtehTdeIOVpNoolw:taBegreecwaoannrdneePocoftiltoahnrei.ty

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance

Item Name

Quantity

Description

1

Model Name
QND-6073R/ QND-6083R

Camera

1

QNO-6073R/ QNO-6083R

Quick Guide
Warranty card (Optional)
Template
Power Terminal Block L Wrench

1

QNV-6073R/ QNV-6083R

QND-6073R/

QND-6083R/

1

QNO-6073R/ QNO-6083R/

QNV-6073R/

QNV-6083R

QND-6073R/

QND-6083R/

1

QNO-6073R/ QNO-6083R/

QNV-6073R/

QNV-6083R

QND-6073R/

QND-6083R/

1

Product installation guide

QNO-6073R/ QNO-6083R/

QNV-6073R/

QNV-6083R

QND-6073R/

1

Plugged in the power plug

QND-6083R/ QNV-6073R/

QNV-6083R

1

Used to control the direction of the camera

QNO-6073R/ QNO-6083R

Appearance

Item Name L Wrench (star-shaped)

Quantity

Description

1

Used to remove and replace the dome cover

Model Name
QNV-6073R/ QNV-6083R

3 Card-type moisture absorbent
1

Attached when installed.

QNO-6073R/ QNO-6083R
QNV-6073R/ QNV-6083R

Audio/alarm cable

1

Used to connect with the audio and alarm port

QND-6073R/ QND-6083R

Audio/alarm cable

1

Used to connect with the audio and alarm port

QNV-6073R/ QNV-6083R

RJ45 waterproof accessory

1

Used to install in humid places

QNO-6073R/ QNO-6083R

Sunshield Sunshield fixing screw

1

It protects the camera from the direct sunlight.

QNO-6073R/ QNO-6083R

1

It fixes the sunshield with the camera.

QNO-6073R/ QNO-6083R

Power Cable

1

Used to plug into the power port

QNV-6073R/ QNV-6083R

English _7

overview

Appearance

Item Name

Quantity

Description

Model Name

AT A GLANCE (QND-6073R/QND-6083R)

QND-6073R/ QND-6083R/

Appearance

Cable for the testing monitor

1

Used to test the camera connection to a portable display device

QNO-6073R/ QNO-6083R/

QNV-6073R/

QNV-6083R

a

Cap Installer

1

Used when connecting RJ45 cable

QNV-6073R/ QNV-6083R

Cable bush

1

Used to connect the LAN cable

QNV-6073R/ QNV-6083R

Optional Accessories for Installation
For your easier installation, you can purchase appropriate optional accessories available.

b

c

Model name QNV-6073R/6083R QND-6073R/6083R
QNO-6073R/6083R

Hanging Mount

Back Box

SBP-301HMW2 SBV-136BW

SBP-122HMW

SBO-100B1

Pole Mount SBP-302PM

All
SBP-300LMW (Parapet Mount)
SBP-300CMW (Ceiling Mount)
SBP-300WMW1 (Wall Mount)
SBP-300NBW (Instalation Box)
SBP-300PMW (Pole Mount)
SBP-300KMW (Corner Mount)

Item
a Dome cover b Camera Case c Microphone hole

Description Case cover used to protect the lens and the main unit. Housing part that covers the camera body. Microphone is embedded.

8_ overview

Components
a

bc

LiNK ACT
NETWORK

f
m l

N

T

W

F AF VIDEO

VIDEO

RES3E,T41A,U2ADLIOAORUMTIN/OUT

RES3E,T41A,U2ADLIOAORUMTIN/OUT

kji

hg

n

Item
a Inside cover b Illumination Sensor c Lens

Description Protective cover for the main body. Detects incoming light to control the IR LED. Lens for the camera.

Item
d IR LED

Description These infrared LED’s are controlled by the illumination sensor.

e Power Port

Port for power terminal block.

d

f Microphone hole

Microphone is embedded.

g Network Port

Used to connect the PoE or Ethernet cable for network connection.

h Micro SD Memory Card Compartment

Compartment for the Micro SD memory card.

ARM-IN

Used to connect the alarm input sensor or external day/night sensor.

e

i Alarm I/O port / Audio Out port

ARM-OUT GND

Used to connect the alarm output signal. These are common ports to connect alarm input/output signals.

AUDIO OUT

Used to connect to speakers.

j Reset Button

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.
J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the Device Manager program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

k Test Monitor Out

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

l Zoom control lever (QND-6073R)

T

Zoom in (Tele)

W

Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

N

Focusing on a near object (Near)

m Focus control lever (QND-6073R)

F

Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

T

Zoom in (Tele)

W

n Zoom/Focus Control Button (QND-6083R)

N

F

Zoom out (Wide) Focusing on a near object (Near) Focusing on a far object (Far)

Focus Control

Press this button for automatic focus control.

English _9

OVERVIEW

overview
AT A GLANCE (QNO-6073R/QNO-6083R)
Appearance
a bc d
e
f g

d c

10_ overview

e

h

Item
a Micro SD card slot

Description (Internal space of the product) This is a slot in which you can insert a Micro SD card.

b Reset button
c Test Monitor Out d Sunshield fixing screw

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be
enabled. If there is no DHCP server in the network, you must run the Device Manager program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.
Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.
It fixes the sunshield with the camera.

e Sunshield

It protects the camera from the direct sunlight.

N

Focusing on a near object (Near)

f Focus control lever (QNO-6073R)

F

Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

T

Zoom in (Tele)

g Zoom control lever (QNO-6073R)

W

Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

T

Zoom in (Tele)

W

h Zoom/Focus Control Button (QNO-6083R)

N

F

Zoom out (Wide) Focusing on a near object (Near) Focusing on a far object (Far)

Focus Control

Press this button for automatic focus control.

Components
a
b c d e

CAUTION:Be ware of the Rated Voltage and Polarity of the power connection.

Item
a Power Port
b Alarm I/O Port
c Network Port d Audio In Jack e Audio Out Jack

Description

Used to plug the power cable.

ARM-OUT GND ARM-IN

Used to connect the alarm output signal. These are common ports to connect alarm input/output signals. Used to connect the alarm input sensor or external day/night sensor.

Used to connect the PoE or Ethernet cable for network connection.

Used to connect to a microphone.

Used to connect to speakers.

English _11

OVERVIEW

overview
AT A GLANCE (QNV-6073R/QNV-6083R)
Appearance
a

b

Item
a Dome cover b Camera Case

Description Case cover used to protect the lens and the main unit. Housing part that covers the camera body.

12_ overview

Components

ab c

RESET

k j

FRONT

DC12V

1 2G3N4D5 RESET

6

7

1,23A,4LAA5URAMDUIOIDNIO/OOUIUNTT

VIDEO

d e f
g

12G3N4D567 1,23,A4LAA5RUADMIUIODNI/OOOUIUTNT

ACT NETWORKLINK

i

h

FRONT

DC12V

T

1 2G3N4D5 RESET

67

1,23A,4LAA5URAMDUIOIDNIO/OOUIUNTT

N

F

AF

VIDEO

W

l

RESET

OVERVIEW

Item
a Illumination Sensor

Description Detects incoming light to control the IR LED.

b Lens

Lens for the camera.

c IR LED

These infrared LED’s are controlled by the illumination sensor.

ARM-IN

Used to connect the alarm input sensor or external day/night sensor.

d Alarm I/O port / Audio I/O port
e Reset button f Test Monitor Out g Power Port

ARM-OUT

Used to connect the alarm output signal.

GND

These are common ports to connect alarm input/output signals.

AUDIO IN

Used to connect to a microphone.

AUDIO OUT

Used to connect to speakers.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.
J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the Device Manager program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

Port for power terminal block.

h Network Port

Used to connect the PoE or Ethernet cable for network connection.

i Micro SD Memory Card Compartment
j Zoom control lever (QNV-6073R)

Compartment for the Micro SD memory card.

T

Zoom in (Tele)

W

Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

Item

Description

N

Focusing on a near object (Near)

k Focus control lever (QNV-6073R)

F

Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

T

Zoom in (Tele)

W

l Zoom/Focus Control Button (QNV-6083R)

N

F

Zoom out (Wide) Focusing on a near object (Near) Focusing on a far object (Far)

Focus Control

Press this button for automatic focus control.

English _13

installation & connection

INSTALLATION (QND-6073R/QND-6083R)

Precautions before installation
Ensure you read out the following instructions before installing the camera:
· It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

Installation
1. Consider the direction to be monitored, attach the template, and drill holes by following the template.

· Stuck-in or peeled-off cables can cause damage to the product or a fire.

· For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

· For the manual variable focal lens camera, features such as focus and zoom should be adjusted before installation. When adjusting these, be sure to prevent foreign substances from becoming attached.
Disassembling

2. Using 2 tapping screws, fix the camera at 2 holes drilled with a template.
` Set the < > mark imprinted on the camera to face the direction of camera monitoring.

1. Use one hand to hold the camera’s bottom part and turn the cover counterclockwise with another hand to separate it.

Dome Cover

3. Connect the camera internal terminal with the corresponding cable.

LiNK ACT NETWORK

4. Adjust the lens in a desired direction by referring to the “Adjusting

J ` Do not touch the transparent part of the dome cover once the protective film is removed.

the monitoring direction for the camera” section. (page 19)

J ` For the manual variable focal lens camera, features such as focus and zoom should be adjusted before installation.

When adjusting these, be sure to prevent foreign substances from becoming

attached.

LiNK ACT NETWORK
LiNK ACT NETWORK

2. Lift up the inner cover to separate it.

5. Please connect the inner cover to the main body.
6. While grabbing the bottom side of the camera with your hand, please grab and push its cover with the other hand to align the two arrow signs, as shown in the figure.
LiNK ACT NETWORK
J To assemble the dome cover, make the arrows match each other and press the cover firmly. If the dome cover is rotated during assembly or is assembled incorrectly, diffused reflection may occur or the lens section may rotate, which will cause the shooting range to be changed. Make sure that the dome cover is correctly connected to the bottom part as shown in the figure. If the snap-fit is not connected correctly, the dome cover may fall, which may cause injury.

14_ installation & connection

INSTALLATION & CONNECTION

INSTALLATION (QNO-6073R/QNO-6083R)

J ` This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Precautions before installation
Ensure you read out the following instructions before installing the camera:
· It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.
· Stuck-in or peeled-off cables can cause damage to the product or a fire. · For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case. · For the manual variable focal lens camera, features such as focus and zoom should be adjusted before
installation. When adjusting these, be sure to prevent foreign substances from becoming attached.

Installation
1. Consider the direction to be monitored, attach the template, and drill holes by following the template.

Mounting Template

Cable Line

2. Insert and fasten 3 tapping screws into 3 holes to secure the camera.
3. Connect the appropriate cables with camera terminals.

4. Adjust the camera direction using the L wrench provided.
J ` When you adjust the camera position using a bracket, please loosen the bracket screw, adjust the camera, and tighten it. If you attempt to adjust it forcibly while the screw is tight, it may result in a scratch or other problems.

How to connect the RJ45 waterproof cable to a LAN cable
1. Insert it through the arrow direction.

2. Connect the LAN connector (male) to the cable.

3. Connect the RJ45 modular jack (female) to the RJ45 connector (male).
J ` Please, keep each of the parts separated.

RJ45 connector (male)
RJ45 modular jack (female) Rubber ring

4. Assemble by rotating the RJ45 modular jack (female) and the RJ45 protection cover clockwise (Follow the arrow).

RJ45 connector protection cover
Back cover
Rubber ring Cable waterproof gasket

5. Assemble by rotating RJ45 protection cover and back cover clockwise (Follow the arrow). When the back cover is assembled, the cable waterproof gasket is tightly attached to the cable to make it waterproof.
J ` You must fully assemble it to rotate the back cover up to the end of the screw thread of the RJ45 connector.

English _15

installation & connection

Outdoor installation
When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, AUDIO, and LAN cables.
2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

Camera Camera

System System

J ` If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping.

A Camera

` Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

A System

To adjust the zoom factor or focus (QNO-6073R)
1. Loosen the front cover as shown. 2. Loosen the zoom/focus lever slightly. 3. Position the zoom/focus lever to WIDE (NEAR) or TELE (FAR) as appropriate. 4. Then, tighten the zoom/focus lever to fix the adjusted position. 5. Turn the front cover to tighten it.

INSTALLATION (QNV-6073R/QNV-6083R)

J ` This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Precautions before installation
Ensure you read out the following instructions before installing the camera:
· It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.
· Stuck-in or peeled-off cables can cause damage to the product or a fire. · For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case. · For the manual variable focal lens camera, features such as focus and zoom should be adjusted before installation.
When adjusting these, be sure to prevent foreign substances from becoming attached.

Disassembling
1. Using the L wrench provided, turn the 3 fastening bolts on the dome cover counter clockwise to remove the cover.

Dome cover

RESET

Zoom Lever WIDE ® TELE

Front cover

Focus Lever FAR ® NEAR

J To ensure seamless waterproofing, tighten up the front cover by turning it to the end. When combining the front cover, please combine the main body and the front cover so that the LOCK indicator is interlocked. Use the lever to adjust the zoom factor or focus, and turn the lever clockwise to fix it. ` Before you can adjust the zoom factor/focus of the lens, loosen and remove the front cover.

Bolts
DC12V
Camera Body

FRONT

1234A5LMAUIND/IOOUITN

Camera Case

16_ installation & connection

DC12V

Installation
1. Using the template provided as an accessory, drill holes for installation screws (at least 55mm deep with a diameter of 6mm).
2. Align the installation holes of the camera, and then insert and fasten tapping screws (M4.5 x L50).
3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the camera.
4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 19)
5. Close the dome cover. Securely fasten the fastening bolt using an L wrench to prevent water from leaking. Connecting the LAN cable 1\. Remove the dome cover and the case. 2. Pull out the Cable bush on the bottom as shown in the figure. J Use an appropriate cable bush for the LAN cable to be connected. – Basic camera : Use the cable with a diameter of Ø5~6.5.

1234AL5MAIUND/IOOUITN

RESET

FRONT

3. Pull off the extruded part of the 1-hole bush provided. 4. Use the Cap installer to pass through the LAN cable.

5. Route the LAN cable through the hole created after removing the cable bush in Step 2, and then connect it to the ethernet terminal.
6. Insert the bush of the LAN cable into the hole.

12G3N4D567 1,23,A4LAA5RUADMIUIODNI/OOOUIUTNT

RESET

ACT NETWORKLINK

Connecting the audio/alarm cable and power cable
1. Remove the dome cover and the case. 2. Pull out the Cable bush on the bottom as shown in the figure.
3. Pull off the small extruded part on the bush of the alarm/audio cable, and route the power cable through the bush.
4. Route the alarm/audio cable through the hole left after removing the cable bush in Step 2. Connect each to the alarm/audio terminal and power terminal block of the PCB, respectively.
5. When mounting the camera, hang the cables on the fixed hook to avoid cables from being damaged or pinched.
6. Insert the bush of the alarm/audio cables into the hole. 7. Adjust the lens in a desired direction by referring to the “Adjusting
the monitoring direction for the camera” section. (page 19) 8. Attach the dome cover.

12G3N4D567 1,23,A4LAA5RUADMIUIODNI/OOOUIUTNT

ACT NETWORKLINK o fRtahCteAe dUp oTVwIoOel tNra:gcBoe neannwedacrtPei ooonl a.f rti ht ye
English _17

INSTALLATION & CONNECTION

installation & connection
Attaching to the unbundled adapter
Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.
1. Remove the dome cover from the case by referring to the “Disassembling” section. (page 16) 2. Use the machine screw to fix the camera case to the unbundled adapter. 3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the
camera. 4. Install the camera body in the reverse order of “Disassembling”. 5. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the
camera” section. (page 19) 6. Close the dome cover.
` Securely fasten the fastening bolt using an L wrench to prevent water from leaking.

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

Camera Camera

1. Connect the power, I/O, AUDIO, and LAN cables.

A

2. Wrap the black cable jacket (Area A) and the cable connection area Camera with waterproof (butyl rubber) tape so that more than half of the

butyl rubber tape is overlapped.

System
System A
System

J If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping. Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

18_ installation & connection

INSTALLATION & CONNECTION

Adjusting the monitoring direction for the camera (QND-6073R/QND-6083R/ QNV- 6073R/QNV-6083R)
Pan

Tilt

LiNK ACT NETWORK

Lens rotation

Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation. – The effective range of pan is a total of 350 degrees. – The effective range of rotation is a total of 355 degrees. – The effective range of tilt is a total of 67 degrees. J The image can be covered up by the camera case depending on the angle.
Do not forcefully turn the focus/zoom lens after the dome case is disassembled. Otherwise, it may cause an incorrect focus due to a motor failure. Methods of adjustment
1. After installing the camera, adjust the panning angle in consideration of the monitoring direction. 2. Set the horizontal angle so that the image is not reversed. 3. Adjust the tilt angle so that the camera faces toward the monitoring object.

INSERTING/REMOVING A MICRO SD MEMORY CARD
J Disconnect the power cable from the camera before inserting the Micro SD memory card. Do not insert the Micro SD memory card while it’s upside down by force. Otherwise, it may damage the Micro SD memory card.
When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended. Disassembly of the product cover should be finished within 5 minutes, or there will be the risk of internal dew condensation. Inserting a Micro SD Memory Card (QNO-6073R/QNO-6083R) 1. Turn the front cover to the UNLOCK [ ] direction.
2. Pull and separate the front cover.
3. Insert a Micro SD card in the arrow direction shown in the figure.

English _19

installation & connection
Inserting a Micro SD Memory Card (QND-6073R/QND-6083R/QNV-6073R/QNV-6083R)
1. Separate the Dome cover of the camera. 2. Insert a Micro SD card in the arrow direction shown in the figure.

Removing a Micro SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

VIDEO VIDEO

RES3E,T41A,U2ADLIOAORUMTIN/OUT
<QND-6073R/6083R>
ACT NETWORKLINK
<QNV-6073R/6083R>
20_ installation & connection

12G3N4D567 1,23,A4LAA5RUADMIUIODNI/OOOUIUTNT

RES3E,T41A,U2ADLIOAORUMTIN/OUT
<QND-6073R/6083R>

12G3N4D567 1,23,A4LAA5RUADMIUIODNI/OOOUIUTNT

ACT NETWORKLINK
<QNV-6073R/6083R>

J Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released. Before removing the Micro SD memory card, in , set the device to

and press the [Apply] button and turn the camera off. ` If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or damaged.

POWERING AND NETWORKING
J ` Before plugging the DC 12 V power plug into the outlet, please assemble the terminal block first.

INSTALLATION & CONNECTION

12G3N4D567 1,23,A4LAA5RUADMIUIODNI/OOOUIUTNT
LiNK ACT NETWORK

Ethernet

Power <QND-6073R/6083R>

Power Ethernet

CAUTION:Be ware of the Rated Voltage and Polarity of the power connection.

ACT NETWORKLINK

<QNO-6073R/6083R>

Ethernet Power

o fRtahCteAe dUp oTVwIoOel tNra:gcBoe neannwedacrtPei ooonl a.f rti ht ye
<QNV-6073R/6083R>

English _21

installation & connection

Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.

Power Supply
Use the screwdriver to connect each line (+, ­) of the power cable to the corresponding power port of the camera.

J If both PoE and DC 12V are applied simultaneously, the product will be supplied with power from DC 12V. – You can also use a router featuring PoE to supply power to the camera. – Use PoE that is compliant with the IEEE 802.3af protocols. – It is advisable to use only one power source from PoE and DC 12V. Be careful not to reverse the polarity when you connect the power cable. ` If you want to connect an external device, you must turn off the external device before proceeding.

Network Cable Specification
Item Connector Ethernet
Cable Max Distance PoE Support

Contents RJ45
10/100BASE-T Category 5e 100M IEEE 802.3af

Remark 10/100 Mbps DC Resistance 0.125 /m

J ` If you use a cable other than Category 5e standards, 100m of transmission distance is not guaranteed.

Connecting to Audio Input/Output
Speaker Microphone PC
Network

Microphone Amp Microphone

Amp Speaker Speaker

Microphone Amp Microphone

Speaker Amp Speaker

1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the microphone is connected to.
2. Check the specifications for audio input.
J ` The QND model supports the built-in microphone only.
· Audio Codec – Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz) – Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)
· Full duplex Audio · Audio in (QND-6073R/6083R) : Built-in microphone · Audio in (QNO-6073R/6083R, QNV-6073R/6083R) : Selectable (microphone/Line-in),
Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm · Audio out : Line out (3.5mm mono jack), Max output level: 1 Vrms

22_ installation & connection

Connecting to the I/O port box
Connect the Alarm I/O cable to the corresponding port of the port box.

RES3E,T41A,U2ADLIOAORUMTIN/OUT

Sensor

Alarm (Warning lamp)
<QND-6073R/6083R>

CAUTION:Be ware of the Rated Voltage and Polarity of the power connection.

Alarm Sensor (Warning lamp)
<QNO-6073R/QNO-6083R>

INSTALLATION & CONNECTION
VIDEO

RESEETT

FRONT

DDC12V

T

N

F

AF W

12R3E14S2E5GA3LNT4MD5A6IUN7D/1OIO,2U3A,IT4NLAA5URAMDUIOIDNIO/OOUIUNTT VIDEO

Sensor

Alarm

(Warning lamp)

<QNV-6073R/QNV-6083R>
· ALARM-IN : Used to connect the alarm input sensor or external day/night sensor. · ALARM-OUT : Used to connect the alarm output signal. · GND : Common port for alarm in/output signal.
J ` If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction. Refer to the “Alarm Out Wiring Diagram” when connecting devices that exceed the voltage and current specifications. (page 24)

To connect the external sensor
Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.

English _23

installation & connection

Alarm In Wiring Diagram

External connection

Inside of the camera

VCC_3.3V

Sensor

ALARM IN (5mA SINK)

RESISTOR

RESISTOR

RESISTOR

DIODE

MLCC TRANSISTOR

GND GND

To connect the alarm out
If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.
Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and current specifications.

Alarm Out Wiring Diagram

Warning lamp / Siren power

(-)

(+)

Warning lamp / Siren

External connection
DC 5V or 3.3V

Inside of the camera

DIODE RELAY

RESISTOR 10K ohm TRANSISTOR
GND

ALARM OUT (12VDC 20mA MAX)

RESISTOR

TRANSISTOR

GND GND

24_ installation & connection

NETWORK CONNECTION AND SETUP

network connection and setup
You can set up the network settings according to your network configurations.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC. 2. Enter the IP address of the camera in the address bar of the browser.

Camera Camera

INTERNET

External Remote PC

Local PC

DDNS Server (Data Center, KOREA)

M A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator. In the Device Manager, you can use the initial password, “4321” to set IP Address, Subnet Mask, Gateway, HTTP Port, VNP Port, IP type. After changing the network interface, for better security, access the web viewer and change the password.
` By factory default, the IP address will be assigned from the DHCP server automatically. If there is no DHCP server available, the IP address will be set to 192.168.1.100. To change the IP address, use the Device Manager. For further details on Device Manager use, refer to “Using Device Manager”. (Page 26)

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM

Camera

DSL/Cable Modem

INTERNET

External Remote PC

DDNS Server (Data Center, KOREA)
1. Connect the user PC directly with the network camera. 2. Run the Device Manager and change the IP address of the camera so that you can use the web browser
on your desktop to connect to the camera. 3. Use the Internet browser to connect to the web viewer. 4. Move to [Setup] page. 5. Move to [Network] ­ [DDNS] and configure the DDNS settings. 6. Move to [Basic] ­ [IP & Port], and set the IP type to [DHCP]. 7. Connect the camera, which was removed from your PC, directly to the modem. 8. Restart the camera.
M For information on how to set DDNS, refer to the online help of Web Viewer. For information on how to set the IP format, refer to the online help of Web Viewer.

English _25

network connection and setup
USING DEVICE MANAGER
M Device manager program can be downloaded from <Technical Support>-<Online Tool> menu at Hanwha Techwin website (http://www.hanwha-security.com). More instructions of Device Manager can be found at menu of the main page.
AUTOMATICALLY SEARCHING CAMERA
If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function.
1. Click at the main page of device manager. 2. Check the camera from the list.
· Check MAC address at the sticker attached to the camera.
CONFIGURING IP ADDRESS
If you want to change camera network setting, sign must be displayed at . Click at the main page to log in.
Configuring Static IP
Manually insert and configure IP address & port information. 1. Click the camera from the list that you want the change the
IP setting. 2. Click at the main page of device manager. 3. Select

. · IP information of the camera will be displayed as previously set. 4\. Fill in IP & Port related categories. If not using a Broadband Router For setting , , and , contact your network administrator. · HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. · RTSP Port: A port that controls real-time streaming. The initial value is 554.

If using a Broadband Router
· IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.2~254
· Subnet Mask : The of the Broadband Router will be the <Subnet Mask> of the camera.
· Gateway : The of the Broadband Router will be the

of the camera.

M The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router. For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”. (Page 28)

If the Broadband Router has more than one camera connected Configure the IP related settings and the Port related settings distinctly with each other. ex)

Category

Camera #1

Camera #2

IP related settings

IP Address Subnet Mask Gateway

192.168.1.100 255.255.255.0 192.168.1.1

192.168.1.101 255.255.255.0 192.168.1.1

Port related settings

HTTP Port RTSP Port

8080 554

8081 555

M ` If the is set other than 80, you must provide the number in the address bar of the Internet browser before you can access the camera. ex) http://IP address : HTTP Port http://192.168.1.100:8080
5. Click [Apply] Button. 6. If the success message is displayed, click [OK].

26_ network connection and setup

NETWORK CONNECTION AND SETUP

Configuring Dynamic IP
Receive IP address from DHCP
· Example of the Dynamic IP environment – If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server
– If connecting the camera directly to modem using the DHCP protocols
– If IPs are assigned by the internal DHCP server via the LAN
1. Click the camera from the list that you want to change the IP setting.
2. Click at the main page of device manager. 3. Select <Obtain an IP address automatically (DHCP)>. 4. Click [Apply] button. 5. If the success message is displayed, click [OK].

AUTOMATICALLY CONFIGURING IP

1. Click the camera from the list that you want to automatically

configure the IP.

QNV-6073R

2. Click < + > at the main page of device manager. · Equipment Setting menu appears.

3. At the menu, click .

4. Click [Close] button.

MANUALLY REGISTERING CAMERA
If the camera cannot be found using search function, the camera can be registered remotely by manually inserting IP information, if the camera is connected to external network.
1. Click at the main page of device manager.
2. Insert the range of IP address that you search. 3. Select the of the camera that you register,
and insert HTTP port, ID, and password. 4. Click [Register] button. 5. Check if camera is registered.
· Check MAC address at the sticker attached to the camera.

English _27

network connection and setup
PORT RANGE FORWARD (PORT MAPPING) SETUP
If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it.
Manual Port Range Forwarding
1. From the Setup menu of the Broadband Router, select <Applications & Gaming> – . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router.
2. Select and for each connected camera to the Broadband Router. The number of each port to be configured to the IP router should be set according to the port number designated in – <IP & Port> on the camera web viewer.
3. When done, click [Save Settings]. Your settings will be saved.
M Port forwarding setting is an example of setting CISCO IP router. The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router.

Setting up Port Range Forward for several network cameras
· You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. · A user can change each port using the camera setting screen.
When Camera1 and Camera2 are connected to a router :

User

Internet

Broadband Router

Start

End

Protocol

IP Address

3000 3000 TCP/UDP 192.168.1.100

3001 3001 TCP/UDP 192.168.1.101

8080 8080 TCP/UDP 192.168.1.100

8081 8081 TCP/UDP 192.168.1.101

Camera1 (192.168.1.100)

HTTP port

8080

RTSP port

3000

Camera2 (192.168.1.101)

HTTP port

8081

RTSP port

3001

M ` Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. After connecting the network camera, select the checkbox from the menu in <Wisenet DDNS> in “Settings -> Network -> DDNS”.

28_ network connection and setup

CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC
1. Run device manager. It will scan for connected cameras and display them as a list.
2. Double-click a camera to access. The Internet browser starts and connects to the camera.
M Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser. CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET On a remote computer that is not in the Broadband Router’s network cluster is not allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL. 1\. Before you can access a camera in the Broadband Router network, you should have set the port range forward for the Broadband Router. 2\. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the IP address of the Broadband Router in the address bar. ex) http://ddns.hanwha-security.com/ID M To use Wisenet DDNS, sign up at the Wisenet DDNS homepage (http://ddns .hanwha-security.com) and register the product at [My DDNS]>[Register Product].

English _29

NETWORK CONNECTION AND SETUP

web viewer
CONNECTING TO THE CAMERA
Normally, you would
1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar.
ex) · IP address (IPv4) : 192.168.1.100 http://192.168.1.100 – the Login dialog should appear. · IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] – the Login dialog should appear.
If the HTTP port is other than 80
1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar.
ex) IP address : 192.168.1.100:HTTP Port number(8080) http://192.168.1.100:8080 – the Login dialog should appear.
Using URL
1. Launch the Internet browser. 2. Type the DDNS URL of the camera in the address bar.
ex) URL address : http://ddns.hanwha-security.com/ID – the Login dialog should appear.
J ` Network connection is disabled in the LAN only environment.
Connecting via UPnP
1. Run the client or operating system in support of the UPnP protocol. 2. Click the camera name for search.
In the Windows operating system, click the camera name searched from the network menu. – The login window is displayed.

Connecting via Bonjour
1. Run the client or operating system in support of the Bonjour protocol. 2. Click the camera name for search.
In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. – The login window is displayed.
To check the DDNS address
If the camera is connected directly to the DHCP cable modem, DSL modem, the IP address of your network will be changed each time you try to connect to the ISP (Internet Service Provider) server. If this is the case, you will not be informed of the IP address changed by DDNS. Once you register a dynamic IP- based device with the DDNS server, you can easily check the changed IP when you try to access the device. To register your device to the server, visit http://ddns.hanwha-security.com and register your device first, and then set the Web Viewer’s to , as well as providing that had been used for DDNS registration.

30_ web viewer

WEB VIEWER

PASSWORD SETTING
When you access the product for the first time, you must register the login password. When the “Password change” window appears, enter the new password.
J For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. – Special characters that are allowed. : ~!@#$%^*()_-+=|{}[].?/ For higher security, you are not recommended to repeat the same characters or consecutive keyboard inputs for your passwords. If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose your password by using a memo pad or memorizing it.
LOGIN
Whenever you access the camera, the login window appears. Enter the User ID and password to access the camera.
1. Enter “admin” in the input box. The administrator ID, “admin”, is fixed and can not be changed.
2. Enter the password in the input field. 3. Click [OK].
If you have logged in successfully, you will the Live Viewer screen.
J When you access the camera web viewer, pay special attention to the security by checking whether the image data is encrypted. M If you check the “Remember my credentials” option when your input is done, in future you will be logged in automatically without being prompted to enter the login information.
` You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut the image on the borders.

CAMERA WEB VIEWER SETUP
1. Click the [Setup ( )] icon. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and
system over the network. 4. Click <Help ( )> to view detailed descriptions of each function.

English _31

appendix

TROUBLESHOOTING

PROBLEM

SOLUTION

No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS.

y On the authentication popup window prompted when initially accessing https, click “View Authentication Certificate” and select the “Always trust when connecting to the designated webviewer IP” check box.
y If the webviewer continues failing to display a video after you select “Next” on the message window below, press the command key + Q to exit the Safari browser, access again and follow the procedures stated above.

I can’t access the camera from a web browser.

y Check to make sure that the camera’s Network settings are appropriate.
y Check to make sure that all network cables have been connected properly.
y If connected using DHCP, verify that the camera is able to acquire dynamic IP addresses without any problem.
y If the camera is connected to a Broadband Router, verify that port forwarding is properly configured.

Viewer got disconnected during monitoring.

y Connected Viewers become disconnected upon any change to camera or network configurations.
y Check all network connections.

No video is displayed when I newly access the webviewer or connect streaming to the client.

y The maximum number of profiles available is 3. The connection may be lost if you use 4 or more of profiles. Example) If you access MJPEG, H264 and H265 and then access with a different profile, the connection will be lost.

The camera connected to the network is not detected in the Device Manager y Turn off the firewall settings on your PC and then search the camera again.
program.

Images overlap. No image appears.

y Check whether two or more cameras are set to a single multicast address instead of different addresses. If a single address is used for multiple cameras, the images may overlap.
y If the transmission method is set to multicast, check whether there is a router that supports multicast in the LAN the camera is connected to.

Voice is not recorded even though audio input settings are configured.

y You must enable the

PROBLEM

SOLUTION

of is set to , but no notification e-mail reaches me even when an analysis event had occurred.

y Verify the settings in the following sequence: A. Check <Data & Time> settings. B. The should be set to . C. Check if the

option of menu is checked to use.

Cannot record into the Micro SD memory card.

y Check if the memory card is defective.

y Check if the memory card is inserted in the proper direction. Operation of memory card that Micro SD memory card is inserted but is formatted by other devices is not guaranteed with this camera unit the camera does not operate properly. y Format the memory card again in menu.

Cannot record in the NAS.

y Confirm that the information registered in the NAS is correct.

It reports that NAS setting has failed.

y Confirm that the IP address of the NAS is valid.
y Confirm that the ID/password of the NAS is valid.
y Confirm that you can access the folder designated as the default folder using the ID of the NAS.
y Confirm that the NAS SMB/CIFS items are unchecked.
y Confirm that the NAS IP address and the camera IP address are in the same format. ex) The NAS & camera subnet mask initial value is 255.255.255.0. If the IP address is 192.168.20.32 then the NAS IP address should be in the range of 192.168.20.1~192.168.20.255.
y Check whether you tried to access as another user without formatting the default folder saved or used.
y Confirm that you used recommended NAS equipment.

32_ appendix

OPEN SOURCE ANNOUNCEMENT

GPL/LGPL software license

The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@hanwha.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.

GPL SW
Component Name
Base Kernel Busybox iproute2-4.3.0 iptables-1.4.21 ethtool-4.2 mtd-1.5.2 mii- diag-2.11 rp-pppoe-3.11 wpa_supplicant-2.5 bash-4.3.30 zeroconf

License
GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 3.0 GPL 2.0

URL
http://www.busybox.net/downloads/snapshots http://ftp.netfilter.org/pub/iptables ftp://ftp.infradead.org/pub/mtd-utils http://www.roaringpenguin.com/pppoe/

LGPL SW
Component Name
gLibc Inetutils neon-0.29.6

License
LGPL 2.0 LGPL 3.0 LGPL 2.0

URL http://www.webdav.org/neon/

GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C)1989, 1991 Free Software Foundation, Inc. 51 Franklin Street,Fifth Floor, Boston, MA 02110-1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software– to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs ; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps : (1)copyright the software, and (2)offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin S 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law : that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License ; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty ; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions :
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run,you must cause it, when started running for such interactive use in the most
ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception:if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you ; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program)on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2)in object code or executable form under the terms of Sections 1 and 2
above provided that you also do one of the following : a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange ; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machinereadable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange ; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major

components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminatedso long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise)that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royaltyfree redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system ; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries,so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation,write to the Free Software Foundation ; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “ASIS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAMPROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty ; and each file should have at least the “copyright” line and a pointer to where the full notice is found.one line to give the program’s name and an idea of what it does. Copyright (C)yyyy name of author This program is free software ; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation ; either version 2 of the License, or (at your option)any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY ; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program ; if not, write to the Free Software Foundation, Inc.,51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode : Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY ; for details type show w’. This is free software, and you are welcome to redistribute it under certain conditions ; typeshow c’ for details. The hypothetical commands show w’ andshow c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than show w’ andshow c’ ; they could even be mouse-clicks or menu items– whatever suits your program.

You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright disclaimer” for the program,if necessary. Here is a sample ; alter the names: Yoyodyne, Inc.,hereby disclaims all copyright interest in the program `Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is Lwihcaetn ysoeu want to do, use the GNU Lesser General Public instead of this License.
GNU GENERAL PUBLIC LICENSE Version 3, 29 June 2007 Copyright (C) 2007 Free Software Foundation, Inc. http://fsf.org/ Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program– to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things. To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it. For the developers’ and authors’ protection, the GPL clearly explains that there is no arranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions. Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users. Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on generalpurpose omputers, but in those that do, we wish to avoid the special anger that patents applied to a free program could make it ffectively proprietary. To prevent this, the GPL assures that atents cannot be used to render the program non-free. he precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions. “This License” refers to version 3 of the GNU General Public License. Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. “The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations. To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work. A “covered work” means either the unmodified Program or a work based on the Program. To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well. To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying. An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code. The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work. A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language. The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it. The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries, or generalpurpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work. The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source. The Corresponding Source for a work in source code form is that same work.

2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law. You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you. Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users’ Legal Rights From anti-Circumvention Law. No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies. You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program. You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions. You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant date. b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies
the requirement in section 4 to “keep intact all notices”. c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along
with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it. d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so. A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate. 6. Conveying Non-Source Forms. You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways: a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange. b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge. c) Convey individual copies of the object code with a copy of the written offer to provide the corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b. d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements. e) Convey the object code using peer-to- peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection 6d. A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work. A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product. “Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made. If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).

The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network. Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying. 7. Additional Terms. “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission. Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works
containing it; or c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different
from the original version; or d) Limiting the use for publicity purposes of names of licensors or authors of the material; or e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual
assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors. All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying. If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms. Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way. 8. Termination. You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11). However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you ofthe violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice. Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10. 9. Acceptance Not Required for Having Copies. You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so. 10. Automatic Licensing of Downstream Recipients. Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License. An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts. You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11. Patents. A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor’s “contributor version”. A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License. Each contributor grants you a non-exclusive, worldwide, royaltyfree patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party. If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid. If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a

patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it. A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyedby you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent
license was granted, prior to 28 March 2007. Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law. 12. No Surrender of Others’ Freedom. If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of thisLicense. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program. 13. Use with the GNU Affero General Public License. Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such. 14. Revised Versions of this License. The Free Software Foundation may publish revised and/ or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version. 15. Disclaimer of Warranty. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. Limitation of Liability. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 17. Interpretation of Sections 15 and 16. If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.
OpenSSL Combined License

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org.

Component Name openssl-1.0.2e

License OpenSSL

URL Combined License http://www.openssl.org/source

Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed
by the OpenSSL Projectfor use in the OpenSSL Toolkit. (http://www.openssl.org/)” 4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written
permission. For written permission, please contact openssl-core@openssl.org. 5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the
OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes cryptographic software written by Eric Young(eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com). Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic
software written by Eric Young (eay@cryptsoft.com)” The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-). 4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@cryptsoft. com)” THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]

BSD License
Some software components of this product incorporate source code covered under the BSD license as follows.

Component Name

License

URL

net-snmp-5.7.3 pcre-8.38 libcap-1.7.4 lighttpd-1.4.35 MiniUPnP Project Client pppd-2.4.7

BSD BSD BSD 2.0 BSD 2.0 BSD 2.0 BSD 2.0

http://www.net-snmp.org/about/license.html
http://www.kernel.org/pub/linux/libs/security/linux-privs/libcap2 http://www.opensource.org/licenses/bsd-license.html
http://opensource.org/licenses/BSD-3-Clause

lighttpd is a secure, fast, compliant, and very flexible webserver that has been optimized for high-performance environments. It has a very low memory footprint compared to other webservers and takes care of cpuload. Its advanced feature-set (FastCGI, CGI, Auth, Output-Compression, URL-Rewriting and many more) make lighttpd the perfect webserver-software for every server that suffers load problems. Simple Network Management Protocol (SNMP) is an Internetstandard protocol for managing devices on IP networks. It is used mostly in network management systems to monitor the devices attached to the network for conditions that need administrative attention. Net-SNMP is a suite of applications used to implement SNMP v1, SNMP v2c and SNMP v3 using both IPv4 and IPv6. For more additional information, send email to help.cctv@hanwha.com. Copyright (C) 2004, Kneschke, incremental All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met :
– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. – Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. – Neither the name of the `incremental’ nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 1998-2001 University College London All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met : 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed
by the Computer Science Department at University College London. 4. Neither the name of the University nor of the Department may be used to endorse or promote products derived from this software without specific prior
written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND CONTRIBUTORS “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSEARE DISCLAIMED. IN NO EVENT SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyright (c) 1988, 1989, 1990, 1991, 1993, 1994, 1995, 1996 The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. 3. Neither the name of the Regents of the University of California nor the names of its contributors may be used to endorse or promote products derived from
this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyright (c) 2006, Creative Labs Inc All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. 3. Neither the name of the Creative Labs nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyright (c) 2005-2012, Thomas BERNARD All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. 3. Neither the name of Thomas BERNARD nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR

TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Various copyrights apply to this package, listed in various separate parts below. Please make sure that you read all the parts.
Part 1: CMU/UCD copyright notice: (BSD like) Copyright 1989, 1991, 1992 by Carnegie Mellon University Derivative Work – 1996, 1998-2000 Copyright 1996, 1998-2000 The Regents of the University of California All Rights Reserved Permission to use, copy, modify and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appears in all copies and that both that copyright notice and this permission notice appear in supporting documentation, and that the name of CMU and The Regents of the University of California not be used in advertising or publicity pertaining to distribution of the software without specific written permission. CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Part 2 : Networks Associates Technology, Inc copyright notice (BSD) Copyright (c) 2001-2003, Networks Associates Technology, Inc All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of the Networks Associates Technology, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 3: Cambridge Broadband Ltd. copyrightnotice (BSD) Portions of this code are copyright (c) 2001-2003, Cambridge Broadband Ltd. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy The name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 4: Sun Microsystems, Inc. copyright notice (BSD) Copyright (c) 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Use is subject to license terms below. This distribution may include materials developed by third parties. Sun, Sun Microsystems, the Sun logo and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of the Sun Microsystems, Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 5: Sparta, Inc copyright notice (BSD) Copyright (c) 2003-2009, Sparta, Inc All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the

above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 6: Cisco/BUPTNIC copyright notice (BSD) Copyright (c) 2004, Cisco, Inc and Information Network Center of Beijing University of Posts and Telecommunications. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must repr

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals