Dysaim DOES-TYM-RMCT-SC001 4WD Stunt Vehicle Instructions

Dysaim DOES-TYM-RMCT-SC001 4WD Stunt Vehicle

REMOTE-CONTROL VEHICLE

REMOTE CONTROL VEHICLE BATTERY INSTALLATION AND BATTERY CHARGING

Connect 5V USB device to charge

Open the battery cover.connect the battery

• ln order to protect the performance of the battery pack, do not give the battery pack immediately after use Charge, leave the battery pack for a few minutes before charging.
• When charging, the uSB charger indicator light is on, and the full indicator light is dark,The charging time is about 2-3 hours.
• It is normal for the battery pack to overheat slightly during charging.

REMOTE CONTROL

Click auto demo mode,Long press to turn off the light, long press to turn off music, Long press to turn off gesture sensing.

REMOTE CONTROL BATTERY INSTALLATION

Uses 2×1 .5V”AAA” non rechargeable batteries
Please install the battery correctly according to the polarity indication.(Battery not included)

GRAVITY SENSOR WATCH

Finger button

1. One light illuminating after switching on is normal operation mode;
2. Press 1 quickly to enter the automatic demonstration mode, and hold the pressing to enter the deformation mode;
3. Press quickly the finger button
   • 1 to illuminate two lights and start the transverse drift mode;
4. Press quickly the finger button
   • 1 again to illuminate three lights and start the 360-degree rotation mode;
5. Hold the pressing to switch dance music, do it again to turn off the light and gesture sensing and do it the third time to tum off the sound effects. Repeat the cycle.

The batte ry chared in the toy must be checked regularly to prevent damage to wires and other parts. If damaged, it must be repaired after damage It can only be used after recovery

BATTERY ATTENTION

1. This product is used for remote control vehicles, with a 3.7V rechargeable lithium battery;The remote controller uses two 1.5V AAAnon rechargeable batteries;
2. The battery should be removed and loaded according to the polarity and voltage marks on the toy battery box, and the battery should not be short-circuited;
3. Nonrechargeable batteries cannot be charged,
4. The rechargeable battery must be charged under the supervision of adults;
5. The rechargeable battery should be taken out of the toys before charging;
6. Different types of batteries or old and new batteries should not be mixed;
7. Only the same or equivalent battery as the recommended battery can be used;
8. The exhausted battery should be taken out from the toy. If it is not used for a long time please take out the battery from the toy.
9. The power supply terminal shall not be short-circuited.
10. Do not connect to more than the recommended number of power supplies

2.4G AUTOMATIC CODE MATCHING

1. When the battery is installed on the remote control, the indicator light of the remote control starts to flash. After the battery is installed on the remote control vehicle, the switch is turned on and the connection state is started. When the connection is successful, the remote control indicator light goes out. (failed to connect, please repeat the above operation).
2. Each remote controller can only be connected to one remote control vehicle. When the connection is successful, each vehicle will not interfere with the other.(multiple vehicles cannot be connected at the same time)
3. After one minute, the remote controller did not find the 2.4G signal sent by the remote control vehicle when it was powered on, and the power indicator lamp flickered. Therefore, the power switch must be restarted to check the frequency.
4. When it is necessary to pair other models of remote controller or remote control vehicle, it is necessary to tum of the power supply of the remote control and remote control vehicle before repairing

REMOTE CONTROL OPERATION

Turn on the remote control switch, then turn on the power supply of the remote control car. wait for the code matching to be completed, and then use the remote control to control the remote control car.

CONTROL INSTRUCTIONS FOR REMOTE-CONTROL VEHICLE

GESTURE SOMATOSENSORY CONTROLLED

General Troubleshooting

In the process of using the USB cable of toys, the wires, plug, shell and other parts should be checked regularly to see if they are damaged When damaged, it should be stopped using until it is repaired.

MAINTENANCE

1. Keep away from the fire source, avoid direct sunlight, high temperature, and humidity, or keep it in the car for a long time to avoid short circuits and fire.
2. When not playing, take out the batteries of the remote control car and remote control, and put the remote control and remote control car back into the color box. which can avoid damage or deformation during transportation or storage.
3. The remote control car must be gently wiped with a wet cloth.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>