Eberspacher EASYSTART PRO Vehicle Heater Instruction Manual
- June 9, 2024
- Eberspacher
Table of Contents
Eberspacher EASYSTART PRO Vehicle Heater
error
{
“error”: {
“message”: “You exceeded your current quota, please check your plan and
billing details.”,
“type”: “insufficient_quota”,
“param”: null,
“code”: null
}
}
the following is the text from the user manual / instructions:
Vehicle Heaters | Technical Documentation
EN
OPERATING INSTRUCTIONS
EASYSTART PRO
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Chapter Chapter title
Page
Chapter contents
1 Introduction
1.1 Please read first
4
1.2 Special text formats and presentations
4
1.3 Explanation of the icons
4
1.4 Repair
5
1.5 Disposal
5
1.6 Safety instructions
5
1.7 Intended use
5
1.8 Non-intended use
5
1.9 Disclaimer
5
1.10 Target groups for this document
6
1.11 Instruction obligation of the target groups
6
1.12 EU Declaration of Conformity
7
1.13 UKCA Declaration of Conformity
7
2 Getting to know EasyStart Pro
2.1 General information
8
2.2 Product properties
8
2.3 Description of the operating components
8
3 Notes on operation and setting
3.1 Activating EasyStart Pro
9
3.2 Display
9
3.3 Activating a function
10
3.4 Setting the operating time
10
2
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
3.5 Operating modes
10
3.6 Temperature sensor
11
3.7 Further devices
11
3.8 Factory setting
11
4 Operating and configuring EasyStart Pro
4.1 The menus and their functions
11
4.2 Heating
12
4.3 Ventilation
13
4.4 Settings
14
4.5 Timer
16
4.6 Residual heat
19
4.7 Further menu items
19
5 What to do if …?
5.1 Maintenance interval
21
5.2 Display fault / error
21
5.3 Fault diagnosis and remedy
22
6 Service
6.1 Technical Support
25
22.1000.35.2204.0A | EN | 07.2021
3
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
1 Introduction
1.3 Explanation of the icons
1.1 Please read first
Before you start with the setting and operation of EasyStart Pro, please read
these operating instructions through carefully.
The operating instructions contain important information you require for the
setting and operation of EasyStart Pro.
Please keep the operating instructions in a safe place for future reference.
1.2 Special text formats and presentations
Special text formats and picture symbols are used in these instructions to
emphasise different situations and subjects. Refer to the following examples
for their meanings and appropriate action.
1.2.1 Lists This dot () indicates a list or action step,
list/action step is a sub-section/secondary step of the black dot.
1.2.2 Cross references Underlined blue text denotes a cross-reference, which
can be clicked in the PDF format. The part of the document named in the text
is then displayed.
measures to avert the imminent danger.
measures to avert the potential danger.
measures to avert the potential danger.
Note This note contains recommendations for use and useful tips for the
operation, installation and repair of the product.
4
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
1.4 Repair
Risk of short-circuit due to penetrating liquid. Penetration of liquid into
the receiver unit of the EasyStart Pro can result in dangerous situations.
1.5 Disposal
Dispose of the product only according to the relevant legal regulations.
1.6 Safety instructions
Danger! Always note and follow all information and notes, especially the
safety instructions in this documentation and in the technical description of
the heater. Risk of fire/deflagration due to ignition.
Vehicle Heaters | Technical Documentation
EN
OPERATING INSTRUCTIONS
EASYSTART PRO
Control unit for Eberspächer pre-heaters
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Chapter Chapter title
Page
Chapter contents
1 Introduction
1.1 Please read first
4
1.2 Special text formats and presentations
4
1.3 Explanation of the icons
4
1.4 Repair
5
1.5 Disposal
5
1.6 Safety instructions
5
1.7 Intended use
5
1.8 Non-intended use
5
1.9 Disclaimer
5
1.10 Target groups for this document
6
1.11 Instruction obligation of the target groups
6
1.12 EU Declaration of Conformity
7
1.13 UKCA Declaration of Conformity
7
2 Getting to know EasyStart Pro
2.1 General information
8
2.2 Product properties
8
2.3 Description of the operating components
8
3 Notes on operation and setting
3.1 Activating EasyStart Pro
9
3.2 Display
9
3.3 Activating a function
10
3.4 Setting the operating time
10
2
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
3.5 Operating modes
10
3.6 Temperature sensor
11
3.7 Further devices
11
3.8 Factory setting
11
4 Operating and configuring EasyStart Pro
4.1 The menus and their functions
11
4.2 Heating
12
4.3 Ventilation
13
4.4 Settings
14
4.5 Timer
16
4.6 Residual heat
19
4.7 Further menu items
19
5 What to do if …?
5.1 Maintenance interval
21
5.2 Display fault / error
21
5.3 Fault diagnosis and remedy
22
6 Service
6.1 Technical Support
25
22.1000.35.2204.0A | EN | 07.2021
3
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
1 Introduction
1.3 Explanation of the icons
1.1 Please read first
Before you start with the setting and operation of EasyStart Pro, please read
these operating instructions through carefully.
The operating instructions contain important information you require for the
setting and operation of EasyStart Pro.
Please keep the operating instructions in a safe place for future reference.
1.2 Special text formats and presentations
Special text formats and picture symbols are used in these instructions to
emphasise different situations and subjects. Refer to the following examples
for their meanings and appropriate action.
1.2.1 Lists This dot () indicates a list or action step,
introduced by a heading. If an indented dash () follows a “dot”, this
list/action step is a sub-section/secondary step of the black dot.
1.2.2 Cross references Underlined blue text denotes a cross-reference, which
can be clicked in the PDF format. The part of the document named in the text
is then displayed.
Regulation! This information indicates a statutory regulation. Any violation
of these regulations results in expiry of the type-approval for the heater and
exclusion of any guarantee and liability claims against Eberspächer Climate
Control Systems GmbH.
Danger! “Danger” indicates a situation that can directly result in death or
serious injuries if not avoided. Æ This arrow indicates the appropriate
measures to avert the imminent danger.
Warning! “Warning” indicates a situation that can potentially result in death
or serious injuries if not avoided. Æ This arrow indicates the appropriate
measures to avert the potential danger.
Caution! “Caution” indicates a situation that can potentially result in minor
or slight injuries or damage to the device. Æ This arrow indicates the
appropriate
measures to avert the potential danger.
Note This note contains recommendations for use and useful tips for the
operation, installation and repair of the product.
4
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
1.4 Repair
Repair of the EasyStart Pro control unit is not permitted. Failure to comply
with this will void the warranty and this will lead to the exclusion of any
warranty and liability on the part of Eberspächer Climate Control Systems
GmbH.
Risk of short-circuit due to penetrating liquid. Penetration of liquid into
the receiver unit of the EasyStart Pro can result in dangerous situations.
Æ To reduce the risk of an electrical shortcircuit or damage, do not expose
the receiver unit of the EasyStart Pro to moisture.
1.5 Disposal
Dispose of the product only according to the relevant legal regulations.
1.6 Safety instructions
Danger! Always note and follow all information and notes, especially the
safety instructions in this documentation and in the technical description of
the heater. Risk of fire/deflagration due to ignition.
Hazardous situations can occur if the heater is operated in the immediate
vicinity of flammable gases, fumes, liquids or dust. Æ Do not use the
EasyStart Pro control
unit if the heater to be activated is in an environment in which flammable
gases, fumes, liquids or dust are present or could be present. Risk of
poisoning due to escaping exhaust gases. Hazardous situations can occur during
operation of the heater in enclosed rooms. Æ Do not use the EasyStart Pro
control unit if the activated heater is located in enclosed rooms, e.g. in a
garage or a multi-storey car park.
1.7 Intended use
The EasyStart Pro control unit serves for selecting the operation mode, for
setting the operating time, for preselecting the starting time and for
switching a heater and/or other option from Eberspächer Climate Control
Systems GmbH installed in the vehicle ON or OFF.
1.8 Non-intended use
Use of the EasyStart Pro control unit for any purpose other than the intended
use specified by the manufacturer is not permitted.
Æ Use the EasyStart Pro control unit only for its intended purpose.
Do not use the EasyStart Pro control unit if a malfunction could cause a
hazard and / or damage to property.
Do not use the EasyStart Pro control unit if there is reason to assume that
safe operation of the activated heater is no longer assured.
Æ Take all measures to prevent accidental restarting.
1.9 Disclaimer
The manufacturer is not liable for damage caused by improper use or incorrect
operation.
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Failure to comply with the safety instructions makes the guarantee null and
void and this leads to the exclusion of any liability of Eberspächer Climate
Control Systems GmbH.
1.10 Target groups for this document
This document is intended for the following target groups:
Specialist workshop The “specialist workshop” target group includes all
workshops trained by Eberspächer that purchase heaters or air conditioning
systems and their control units, accessories and spare parts from Eberspächer
or the trade and install, repair or service these on behalf of an end user.
Installation shop The “installation shop” target group includes all companies
trained by Eberspächer that purchase heaters or air conditioning systems and
their control units, accessories and spare parts from Eberspächer and install,
repair or service these on behalf of another company (normally the motor
vehicle manufacturer / body builder).
End user The “end user” target group includes all natural persons who operate
a heater or air conditioning system using a control unit, irrespective of
whether as a consumer or as part of their normal work.
1.11 Instruction obligation of the target groups
Each of the above-mentioned target groups must unconditionally observe its
instruction obligation. The instruction obligation includes the passing on of
technical documents.
Technical documents are all documents published for the installation,
operation, maintenance or repair of heaters or air conditioning systems and
their control units, accessories and spare parts from Eberspächer.
Note Unless otherwise expressly stipulated below,
the technical documents may be passed on in printed form, on a data medium or
by Internet download. The latest technical documents are available for
download via the Eberspächer website.
Responsibility of the installation shop The installation shop must pass on the
following technical documents to the contracting company with the obligation
to pass on these to the end user: Technical description Operating instructions
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Responsibility of the specialist workshop The specialist workshop must pass on
the following technical documents to the end user, even if the order comes
from a sub-contractor: Technical description Operating instructions
Note The above-mentioned target groups must ensure that the end users are
provided with the operating instructions on the product prepared by the
manufacturer in printed form and in the end user’s national language. If
necessary, this can be an abridged form of the complete operating instructions
that is additionally included with the product on a data medium or is
available via Internet download.
1.13 UKCA Declaration of Conformity
We herewith declare that the version of the heater placed on the UK market by
us conforms to the applicable provisions of the following UK Directives.
Electromagnetic Compatibility, Statutory Instrument 2016 No. 1091
The full Declaration of Conformity can be viewed and downloaded from the
download centre at www.eberspaecher.com.
1.12 EU Declaration of Conformity
We herewith declare that the control unit placed on the market by us conforms
to the applicable provisions of the following EU Directive.
EU Directive 2014/30/EU
The full Declaration of Conformity can be viewed and downloaded from the download centre at www.eberspaecher.com.
22.1000.35.2204.0A | EN | 07.2021
7
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Getting to know EasyStart Pro
Description of the operating components
2.1 General information
EasyStart Pro has a simple operating structure. All settings, functions and
parameters are controlled with a single operating button.
If the power supply in the vehicle is interrupted (e.g. the battery is
disconnected), EasyStart Pro retains all the basic settings, with the
exception of date and time. When the power supply is restored, only the date
and time have to be set again for timer mode, see page 14.
The use of EasyStart Pro is described in detail from page 9.
2.2 Product properties
EasyStart Pro is a permanently installed control unit for air and water
heaters. It is based on the CAN bus communication and has been designed for
the new Hydronic S3 Economy / Commercial and Airtronic S2 / M2 heater
generations.
EasyStart Pro is generally installed in the cockpit or dash panel of the
vehicle.
EasyStart Pro allows you to make all the necessary settings for heater,
ventilator and timer mode of up to two heaters separately or of two identical
heaters (Airtronic 2 or Hydronic S3) in a group.
22°C
1 Display The display shows the following parameters: Current operating mode
Current interior temperature Operating mode Timer positions Settings Error
codes
2 Operating button The operating button is used to operate, select and program
all the functions and values in EasyStart Pro. Turning selects a
value/function within a
menu. Turning to the right increases a value or
selects the next menu item to the right. Turning to the left decreases a
value or
selects the next menu item to the left. Pressing confirms the flashing menu
item or
value on the display. If EasyStart Pro is in sleep mode (display OFF),
pressing or turning “wakes up” the active display mode. If all heaters are
switched off, the Start
mask will be displayed.
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
When the heater is running, the currently remaining operating time of the heater is displayed. If several heaters are running, the currently remaining operating times will be displayed alternately.
When the heater is running, the currently remaining operating time of the heater is displayed. If several heaters are running, the currently remaining operating times will be displayed alternately.
Note A LONGPRESS (min. 2 sec.) immediately starts
all connected heaters. The standard operating time here is set at the factory
to 30 minutes. During operation, a LONGPRESS (min. 2 sec.) immediately
switches off all connected heaters. If terminal 58 has voltage, sleep mode
will not be activated as long as the vehicle lights are switched on.
3 Notes on operation and setting
3.1 Activating EasyStart Pro
If the display is not lit, EasyStart Pro has to be activated. Pressing the
operating button or BACK button displays the Start mask; you can then continue
with operation or setting.
3 LED ring
The LED ring with its different colours serves to
indicate the operating mode.
Red ring:
Heating mode
Blue ring:
Ventilator mode
Orange ring: Residual heat mode
White ring:
System configuration
Red flashing ring: Fault in one of the
connected heaters or in EasyStart Pro
4 Button BACK The BACK button causes a jump back to the menu or command at the
next higher level. If EasyStart Pro is in sleep mode (display OFF), pressing
“wakes up” the active display mode. If all heaters are switched off, the Start
mask
will be displayed.
3.2 Display
The display is lit During operation of EasyStart Pro When terminal 58 has
voltage, for example
when the vehicle lights are switched on (optional). When the heater is ON (the
display goes out after approx. 30 seconds).
3.2.1 Display language
The display language is set by the workshop during installation. In the
delivery condition of EasyStart Pro, German or English are available as
display languages.
A further 25 display languages are currently available. If necessary, agree on
the display language to be set with your installation workshop. It will then
undertake the necessary configuration.
22.1000.35.2204.0A | EN | 07.2021
9
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
3.2.2 Display goes out The display goes out after approx. 30 seconds if No
settings are made. No heater is switched on. When using terminal 58, when the
vehicle
lights are switched off.
EasyStart Pro then goes to sleep mode. Before going to sleep mode, an overview
mask is displayed. EasyStart Pro then has to be activated (see above) before a
new input can be made.
3.3 Activating a function
The symbol of the function to be activated appears in the middle and flashing
in the display.
Flashing function / flashing value Select the flashing function in the menu
bar by
pressing the operating button. Increase or decrease the flashing value by
turning the operating button. Then confirm the selected value by pressing the
operating button.
Cancel settings Any settings being made can be cancelled with the BACK button
.
Note Settings and changes must always be confirmed by pressing the operating
button, otherwise they will be lost.
3.4 Setting the operating time
The operating time can be set individually using the operating button. Turning
to the right increases the operating
time. Turning to the left decreases the operating
time. Setting range for the operating time:
min. 10 minutes to max. 120 minutes in oneminute steps. The operating time can
be prolonged to infinite. Above the 120th minute, the input is made in
60-minute steps.
Note With air and water heaters, continuous heating
mode [] is also possible. The operating times of all the connected
heaters can be set independently of one another.
3.5 Operating modes
3.5.1 Heating In this operating mode, a water heater heats
the vehicle engine via the coolant circuit and the vehicle interior via the
ventilation louvres, irrespective of the configuration. An air heater heats
the vehicle interior with warm air that is distributed by a fan in the heater.
3.5.2 Ventilation In this operating mode, the water or air heater supplies the vehicle interior with fresh outdoor
10
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
air via the ventilation louvres. This operating mode is only possible if the function is supported by the heater version (see also the Technical Description of the heater).
3.8 Factory setting
Timer mode (for all heaters) Weekday group: Mon Fri Departure time: 07:00 h
3.6 Temperature sensor
EasyStart Pro has an integrated temperature sensor that measures the interior
temperature and regulates the power of the air heater. During installation, an
additional external temperature sensor can be connected and integrated into
the system.
Air heaters Operating time: 30 minutes Maximum operating time: 720 minutes
Target temperature: 22°C / 72°F
Water heaters Operating time: 30 minutes Maximum operating time: 720 minutes
With air heaters, the temperature sensor installed
in the heater for control of the heater can also
4
be used to measure the interior temperature.
This function will be installed by the installing
workshop during initial commissioning.
Operating and configuring EasyStart Pro
3.7 Further devices
EasyStart Pro allows the simultaneous operation of up to 2 heaters, see page
19. It is also possible to combine a heater with a fan. The fan is then used
to circulate the air inside the vehicle.
Note The number of symbols and displays differs depending on the installed
heater and feature options.
4.1 The menus and their functions
Menu bar
22°C Status area
Menu bar The following menus can be selected from the menu bar (turn the
operating button to the right): Symbol Menu
Heat
Ventilate
Residual heat
Settings
Timer
22.1000.35.2204.0A | EN | 07.2021
11
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Note The Ventilation function is only displayed if
the heater supports this function. The timer function is not available on
vehicles in ADR mode. ADR mode is reserved for vehicle
transporting hazardous goods on the road (e.g. road tankers).
Status area When the menu (heating, ventilation, settings, timer or residual
heat) is activated, various items of information are display in the status
area. These are presented and described in the respective sections of these
operating instructions.
Input area
Menu bar
W 107 min X Input area
4.2 Heating
Off
In the Start mask, a flashing heater symbol in the menu bar and the current
temperature and status of the heater are displayed. Possible actions are:
HEATING IMMEDIATELY with LONGPRESS HEATING ON with settings
4.2.1 HEATING IMMEDIATELY with LONGPRESS:
Press operating button for longer than 2 seconds.
Æ Heating mode starts immediately with the last operating time used. The LED
ring lights up red and the residual heating mode time is displayed.
Display: e.g. Heating ON / Operating time 107 min.
In the menu bar, the symbol of the selected menu item appears in the middle of
the display. The corresponding setting value flashes in the input area and can
be altered by turning the operating button to the left or right and confirmed
by pressing.
Note The function LONGPRESS ON is not available in ventilator and residual
heat mode.
4.2.2 HEATING ON with settings: Press the operating button. Select the
operating time by turning the
operating button.
Note With air heaters, select and confirm the target temperature.
Confirm the operating time by pressing the operating button.
12
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Æ Heating mode starts with the set operating time. The LED ring lights up red,
the residual heating mode time and the current temperature are displayed.
Heating mode ends at the end of the set operating time.
Note If an air heater is operated with EasyStart Pro, the desired temperature
can also be set in heating mode. 14°C 36°C in 1°C steps, 57°F 97°F in 1°F
steps.
Note LONGPRESS terminates heating mode
immediately and all further connected heaters are also switched off. If the
heater is connected to the vehicle battery (e.g. car battery), the operating
time of the heater should not exceed the subsequent driving time of the
vehicle. This will ensure that the vehicle battery is sufficiently charged.
Example: Operating time of the heater: 25 minutes Driving time of the vehicle:
min. 25 minutes
Changing the operating time during heating mode Press the operating button.
Select and confirm flashing menu . Select and confirm the settings by turning
and
pressing the operating button . Set the desired operating time by turning and
press to confirm.
Note With air heaters, select and confirm the target temperature beforehand.
Æ Heating mode is continued with the set operating time. The LED ring lights
up red and the residual heating mode time is displayed.
HEATING OFF during heating mode Press the operating button. Select and confirm
flashing menu . When OFF flashes on the display, press the
operating button again. Heating mode is terminated.
4.3 Ventilation
Off
In the Start mask, a flashing fan symbol in the menu bar and the current
temperature and status of the heater are displayed.
4.3.1 VENTILATION ON with settings: Press the operating button. Select the
operating time by turning the
operating button and confirm, or confirm the displayed operating time. Æ
Ventilation mode starts with the set
operating time. The LED ring lights up red and the residual ventilation mode
time is displayed. Ventilation mode ends at the end of the set operating time.
22.1000.35.2204.0A | EN | 07.2021
13
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Changing the operating time during ventilation mode Press the operating
button. Select and confirm flashing menu . Select and confirm the settings by
turning and
pressing the operating button . Set the desired operating time by turning and
press to confirm. Æ Ventilation mode is continued with the set
operating time. The LED ring lights up blue, the residual ventilation mode
time and the current temperature are displayed.
VENTILATION OFF during ventilation mode Press the operating button. Select and
confirm flashing menu . When OFF flashes on the display, press the
operating button again. Ventilation mode is terminated.
Note LONGPRESS terminates ventilation mode immediately. All connected heaters
are switched off.
4.4 Settings
Th
In the Start mask, a flashing gear wheel in the menu bar and the set day of
the week and the current time are displayed.
Possible actions are: Standard settings for day of the week, time
and temperature format Heating at high altitudes: ON / OFF Low temperature
during heating: ON / OFF Fault diagnosis: Display of error messages Reset user
settings
4.4.1 Standard settings Set time:
Select and confirm. Set the hours and confirm. Set the minutes and
confirm. Set time format Select and confirm. Select between 12 h and 24 h
format and
confirm. Set weekday
Select and confirm. Set the day of the week and confirm. Set temperature
format Select and confirm. Select between degrees Celsius and
degrees Fahrenheit and confirm.
14
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
4.4.2 Heating mode at high altitudes
4.4.4 Fault diagnosis
Note This function applies only to the Hydronic S3 12 V. This setting is not
visible on heaters with integrated altitude sensor as it is not required.
When operating the heater at an altitude above 1500 m above sea level, an
adjustment has to be made in this menu in order to regulate the fuel supply
according to the altitude.
Select and confirm. Select between ON (above 1500 m above
sea level) and OFF (below 1500 m above sea level) and confirm.
4.4.3 Low temperature heating mode Low temperature heating mode fulfils the
following functions: Air heaters: Reduction of the outlet
temperature at the air louvre by approx. 10 °C / 18°F (depending on the air
routing), e.g. if the air louvre is near the body or discharges onto
temperature-sensitive components in the vehicle.
Select and confirm. Select between ON and OFF and confirm.
Note This function is only available for air heaters.
Select and confirm. Select and confirm the connected heater
or control unit. The faults are displayed in the order of
their occurrence.
Note If a fault occurs, the symbol
the display during operation:
Heater
appears on
The LED ring flashes red as soon as a fault occurs. It stops flashing when the
error message has been cancelled by pressing the operating button.
Further information on fault diagnosis from on page 22.
4.4.5 Resetting the user settings
Select and confirm. YES resets the user settings in
the EasyStart Pro and deletes the programmed timer, date and other settings.
NO retains the existing user settings in the EasyStart Pro.
22.1000.35.2204.0A | EN | 07.2021
15
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
4.5 Timer
4.5.1 General information on programming the timer positions
The timer selection menu controls up to three programmable timer positions.
The timer positions can either all take place on one weekday or can be
distributed between different weekdays or weekday ranges.
Weekday ranges, e.g. Mon Fri 5 x heat / ventilate Mon Sun 7 x heat /
ventilate If a programmed weekday range is activated, all the days of the week
are processed in turn as long as the timer is active. Renewed programming is
not necessary.
Note If EasyStart Pro is activated with a
programmed weekday range Mon Fri on Sunday, the heater heats or ventilates
from the following Monday to Friday with the set defaults (5x HEATING /
VENTILATION). If EasyStart Pro is activated with a programmed weekday range
Mon Fri on Wednesday, the heater heats or ventilates on Wednesday, Thursday
and Friday. In the following wee, operation is continued with the set defaults
on Monday and Tuesday (5x HEATING / VENTILATION). When a weekday range has
been processed, the time position has to be reactivated for the following
week. If the symbol is not displayed in the menu bar, the heater is in ADR
mode. Timer mode is not possible here.
Start time The heater starts on the selected day on reaching the set starting
time.
Note “Start time” mode is set at the factory. “Departure time” mode has to be
configured by the specialist workshop during installation.
Start time conditions Under the following conditions, the preselected heating
mode is not started on the current day. The current day and the preselected
day are
identical. The current time lies within the time period,
departure time minus operating time. Example:
Current day / preselected day: Thu Current time: 18:45 h Departure time: 19:00
h Operating time: 30 minutes Consequently: Time range for operating time:
18:30 to 19:00 h The current time lies within the time period of the operating
time. The heater is not switched on. The program will be run during the next
week.
In all other configurations the start takes place according to the preset
operating time.
Departure time (with water heaters) The heater starts on the selected day
before reaching the set departure time so that engine and vehicle interior are
heated up in good time. This takes place in line with parameters such as
current temperature, preselected operating time and engine displacement.
16
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
4.5.2 Programming the timer Display ON, the Start display appears. Select in
the menu bar with the operating
button.
Picture 1: Display if no timer is activated.
The following settings are possible: Timer T1 ON / OFF by turning and
pressing the operating button.
After selecting in the menu bar, next select the day of the week / weekday
range by turning the operating button. Each day of the week is selected
individually and confirmed by pressing. Pressing a second time deselects the
day of the week again. At the end of the selection, turn the operating button
to [OK] and press to confirm.
Picture 2: Display if a timer is activated, here T2.
Confirm timer selection by pressing the operating button.
Æ The first timer position T1 appears. Turn the operating button to select the
alternative timer positions T2 or T3.
Mo
Step 2: Setting the starting time. Turning and pressing confirms first the
hour, then the minutes:
30min
Picture 3: T1 with factory settings
The factory settings are: Heating mode Weekday range Mon Fri Starting
time: 7:00 h Operating time: 30 minutes
Call up timer T1 by pressing the operating button. You are now in
configuration mode.
Step 3: Selection of heating or ventilation mode:
Note If an air heater is operated with EasyStart Pro, the desired temperature
in heating mode can also be set before setting the operating time: 14°C 36°C
in 1°C steps, 57°F 97°F in 1°F steps.
22.1000.35.2204.0A | EN | 07.2021
17
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Step 4: Select the operating time: min. 10 minutes max. 120 minutes:
If a timer is activated, the timer symbol appears on the display:
Heater
25min
Note If the heater is connected to the vehicle battery (e.g. car battery), the
operating time of the heater should not exceed the subsequent driving time of
the vehicle. This will ensure that the vehicle battery is sufficiently
charged. Example: Operating time of the heater: 25 minutes Driving time of the
vehicle: min. 25 minutes
Select the heating level (only for water heaters with automatic operating time
calculation) ECO heating level = normal heating HIGH heating level =
comfort heating
After activation of timer T1, the following appears on the display:
06:30
25min
Off
Timer positions T2 and T3 can be configured in the same way.
Note To edit an existing timer, it first has to be selected and then switched
to configuration mode by pressing the operating button. Then carry out steps 1
to 4 as described above.
4.5.3 Deactivate timer To deactivate a timer position, it first has to be
selected with the operating button. Press once and with OFF flashing, press
the operating button again. All operating settings of the timer remain saved.
Note When a weekday range has been processed, the time position has to be
reactivated for the following week.
Heating mode Weekday range Mon Fri Starting time: 6:30 h Operating time: 25 minutes Timer T1 is activated. The heater will be started at the set time on the next working day and will run for 25 minutes.
18
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
4.6 Residual heat
Display before switching on
Off
In the Start mask, a flashing heater symbol in a circle in the menu bar and
the current status of the heater are displayed.
Residual heat mode ON Press the operating button and select ON. Æ Residual
heat mode starts if there is residual
heat in the engine coolant. Æ The LED ring lights up orange. The operating
time of the heating mode depends on the available residual heat. Æ The
operating status and mode of the heater appear on the display:
Heater
In residual heat mode, the heating system uses the residual heat in the
coolant circuit of the warm engine and distributes heated air in the vehicle
interior. In this operating mode, only the water pump and fan are in
operation.
Note Residual heat mode cannot be used if the
coolant temperature is too low. Residual heat mode is only available with
water heaters.
On
Residual heat mode OFF Press the operating button and select OFF. LONGPRESS
(min. 2 sec.) on the operating
button immediately switches off all connected heaters. Æ Residual heat heating
mode stops.
4.7 Further menu items
Possible actions are: Residual heat mode ON Residual heat mode OFF
4.7.1 Control of several heaters EasyStart Pro offers the possibility of
controlling several heaters via one or two control units.
Note Configuration of several heaters with several control units is carried
out by the workshop during installation. Please discuss your configuration
wishes with the workshop before installation.
22.1000.35.2204.0A | EN | 07.2021
19
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Heater 2
Heater 1
Heater 2
Heater 1
The following combinations are possible: Two heaters
Heater 1 (water or air heater) Heater 2 (water or air heater) Æ Each
heater is operated individually.
or
or
Picture 4: Max. 2 ES Pro with 2 separately controller heaters
OR Heater 1 (water heater) Heater 2 (water heater)
Æ Both heaters are controlled simultaneously in a group.
and
Picture 5: Max. 2 ES Pro Pro with 2 water heaters in a group
OR Heater 1 (air heater) Heater 2 (air heater)
Æ Both heaters are controlled simultaneously in a group.
and
Heater group
4.7.2 Configuration example Two heaters are connected and are operated
separately from one another: 1 water heater 1 air heater They are
designated with numbers in the display to distinguish between them. Display
for the water heater:
12
Water Heater
Display for the air heater:
1 2
Air Heater
After selection with the operating button, the operating and timer
possibilities described in this chapter are available for each of the heaters.
The same applies to a heater group.
Note If the LONGPRESS function is used here, all the heaters are switched on
together. The operating time corresponds to the last setting used.
4.7.3 Set standard operating time The standard operating time is set at the
factory to 30 minutes. During operation, the standard operating time
corresponds to the last settings used for the respective heater or heater
group.
Heater 2 Heater 1 Heater group
Picture 6: Max. 2 ES Pro Pro with 2 air heaters in a group
20
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
5 What to do if …?
5.1 Maintenance interval
If a maintenance interval for the connected heaters is set by the workshop
during initial commissioning, EasyStart Pro reminds the user to visit a
specialist workshop to have the maintenance carried out by means of a notice
on the display on expiry of the interval.
5.2 Display fault / error
EasyStart Pro displays faults or errors in the heater or control unit by means
of a red flashing LED ring on the operating button. An error message appears
on the display.
Pressing the operating button cancels the error message and the LED ring stops
flashing. If there are several faults or errors, these will be displayed in
turn by repeatedly pressing the operating button. If several heaters are
connected, the error message will be preceded by either “H1” or “H2” to
clearly localise the fault.
Service
EasyStart Pro prompts the user to switch on the “HEATING” function for 10
minutes even in the summer months after four months of non-operation by means
of a notice on the display. Brief operation removes any residues and deposits
in the combustion chamber and ensures proper operation during the heating
period.
Note Fault diagnosis can also be called up with the function in menu .
Heater ON for 10 Min.
22.1000.35.2204.0A | EN | 07.2021
21
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
5.3 Fault diagnosis and remedy
5.3.1 Heater error messages
Display Service
Description There is a fault in the heater
that can only be remedied by a specialist workshop.
Remedy / Customer Visit an authorised Eberspächer
workshop.
Undervoltage
Undervoltage applied at the heater control box without interruption for at least 20 seconds.
Check battery for a drop in voltage. Charge the battery, if necessary visit
your vehicle workshop.
Overvoltage
Overvoltage applied at the heater control box without interruption for at least 20 seconds.
Check the battery, if necessary visit your vehicle workshop.
Fuel Supply or Pump
Fault in the fuel supply or fuel pump.
Check the fuel line to the heater for free passage, short-circuit and damage.
Pull the plug off the metering pump and inspect for damage.
Check the fuel level in the fuel tank. Visit your vehicle workshop, if
necessary.
Water Circuit or Pump
With water heaters only: Water temperature in the heater too high.
Check the water pump for proper function.
Check the water circulation in the water circuit.
The heater can be reset to the delivery condition by removing the heater fuse.
Recommendation: Visit an authorised Eberspächer workshop to have the fault
remedied.
22
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
Display Air Ducting or Outlet
Overheat. Heater locked.
Restricted Operation
Description With air heaters only: Air
temperature in the heater too high.
Overheating of the heater detected. The heater is interlocked for safety
reasons.
Emergency running of the heater.
Remedy / Customer Check the air lines. Are air lines
clogged or kinked? Are all air louvres free and not blocked by objects? The
heater can be reset to the delivery condition by removing the heater fuse.
Recommendation: Visit an authorised Eberspächer workshop to have the fault
remedied.
The heater can be reset to the delivery condition by removing the heater fuse.
Recommendation: Visit an authorised Eberspächer workshop to have the fault
remedied.
There is a fault in the heater. Restricted operation is still possible,
however (with air heaters with target temperature 20 °C).
Recommendation: Visit an authorised Eberspächer workshop to have the fault
remedied.
22.1000.35.2204.0A | EN | 07.2021
23
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
5.3.2 Control unit error messages
Display
Description
Remedy / Customer
1
The external temperature sensor Check the wiring of the external
Ext. Temp. Sensor is defective. defective
temperature sensor for continuity, short-circuit or damage; replace the
temperature sensor, if necessary.
If the fault cannot be remedied, please
visit your vehicle workshop.
2
Int. Temp. Sensor defective
The internal temperature sensor There is no remedy for this fault. The
is defective.
control unit has to be replaced. Please
visit your vehicle workshop for that.
3
Rotary Knob jammed
The operating button is blocked. Can the operating button be freed again by
hand?
If the fault cannot be remedied, please visit your vehicle workshop.
4
Pushbutton jammed
The button is blocked.
Can the button be freed again by hand?
If the fault cannot be remedied, please visit your vehicle workshop.
7
Timer mode not allowed
Timer mode is not permitted.
Check the configuration. If the fault cannot be remedied, please
visit your vehicle workshop.
8
Operation not supported
The heater is in auxiliary heating Terminate auxiliary heating mode via
mode via Switching Plus and
Switching Plus.
cannot be operated via EasyStart If the fault cannot be remedied, please
Pro during this time.
visit your vehicle workshop.
9
CAN communication error
Communication error on the CAN Inspect the wiring for cable
bus link.
breakages/short-circuits.
If the fault cannot be remedied, please
visit your vehicle workshop.
24
22.1000.35.2204.0A | EN | 07.2021
More information https://www.caravansplus.com.au
Operating Instructions | EasyStart Pro
6 Service
6.1 Technical Support
If you have any technical questions or problems with the heater, the control
unit or the operating software, please contact the following service address:
support-UK@eberspaecher.com
22.1000.35.2204.0A | EN | 07.2021
25
More information https://www.caravansplus.com.au
More information https://www.caravansplus.com.au
More information https://www.caravansplus.com.au
22.1000.35.2204.0A EN 07.2021 Subject to change without notice © Eberspächer Climate Control Systems GmbH
Eberspächer Climate Control Systems GmbH Eberspächerstraße 24 73730 Esslingen
Germany info@eberspaecher.com www.eberspaecher.com Eberspacher (UK) Ltd.
Climate House, Yeoman Road Ringwood, Hampshire BH24 3FA United Kingdom
enquiries@eberspacher.com www.eberspaecher.co.uk
More information https://www.caravansplus.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>