TEMPO 180XL Visual Fault Locator Instruction Manual
- June 13, 2024
- Tempo
Table of Contents
**TEMPO 180XL Visual Fault Locator Instruction Manual
**
Read and understand all of the instructions and safety information in this manual before operating or servicing this tool.
Description
The Tempo Communications 180XL Visual Fault Locator is used to visually locate loss locations such as Macro bends, bad connectors, and other fiber discontinuities. Fiber continuity can also be visually confirmed.
Safety
Safety is essential in the use and maintenance of Tempo tools and equipment. This instruction manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of this tool. Observe all of the safety information provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with the safe operation and maintenance procedures for the Tempo Communications 180XL Visual Fault Locator.
Keep this manual available to all personnel.
Package Contents
- 1 Visual Fault Locator
- 2 AA Batteries
- 1 Instruction manual
- 1 Soft carry case
Important Safety Information
CAUTION
LASER LIGHT
DO NOT STARE INTO BEAM 1 mW max at 640-660 nm CLASS 2 LASER PRODUCT
WARNING
Do not look directly into the output port when the instrument is ON. Never use a viewing instrument such as a magnifier or microscope to view the free end of any optical fiber connected to the 180XL. The use of viewing on active fibers can focus an intense laser beam onto the retina of the eye, resulting in permanent damage or blindness.
Always aim the free end of an active fiber at a nonreflective surface.
Users should always cover the output port with the dust cap when the instrument is not in use.
Do not discard this product or throw away!
For recycling information, go to www.TempoCom.com.
All specifications are nominal and may change as design improvements occur. Tempo Communications shall not be liable for damages resulting from misapplication or misuse of its products.
Operation
- Slide the switch to first position (MOD) to place the 180XL in modulation mode. The green LED will flash indicating modulation mode.
- Slide the switch to the next position (ON) to set the VFL to CW mode. The green LED will indicate CW mode by remaining on all of the time.
- When the LED flashes red, the batteries are low and must be replaced.
Applications
Continuity check
Break in fiber
Macro bend loss
Dirty connectors
The 180XL Visual Fault Locator is designed to quickly locate breaks in optical fibers. Any interruption in continuity will be indicated by red light escaping from the fiber. Light can also escape from the fiber if it is stressed or bent too tightly. In either case, escaping light is a sure sign of a problem.
Cleaning the Output Port
Clean all connectors before inserting them into the 180XL optical port.
For optimal performance it is also recommended that the user routinely cleans the optical port.
To clean the 180XL optical port, insert a Tempo 946 cleaning wand into the
output port until it stops.
Twist the wand, remove it, and discard. Do not reuse the cleaning wand.
Users should always cover the output port with the dust cap when the instrument is not in use.
Note: Do not blow air into the output port to remove dirt particles. Doing so will only pack the dirt and make it harder to remove.
Specifications
| Wavelength | 650 nm ±10 nm |
|---|---|
| Emitter Type | Fabry Perot |
| Maximum Output Power | 0 dBm (1 mW) |
| Range | 7 km |
| Laser Classification | Class 2 |
| Modes of Operation | CW and 2 Hz modulation |
| Method of Display Operation | Green/Red LED |
| Fiber Type | Single mode, multimode |
| Connector Interface | 2.5 mm universal, optional 1.25 mm adapter |
| Battery | AA (2) |
| Battery Life | 80 hours with 3.9 Wh batteries |
| Weight (without batteries) | 70 g (0.15 lb) |
| Dimensions | 180 mm x 23 mm (7.08″ x 0.91″) dia. |
| Operating Temperature | -10 °C to +45 °C (14 °F to 113 °F) |
| Storage Temperature | 40 °C to +70 °C (-40 °F to 158 °F) |
| Certifications | CE, FCC, CDRH, EAC |
Visitez le site www.TempoCom.com pour le manuel d’instructions en Français.
Visite www.TempoCom.com para manual de instruções em Português
Die deutsche Bedienungsanleitung finden Sie auf www.TempoCom.com
Посетите сайт www.TempoCom.com для получения руководства по эксплуатации на русском языке
Para obtener el manual de instrucciones en español visita www.TempoCom.com
Per ottenere il manuale d’istruzione in Italiano, vsita il sito www.TempoCom.com
1390 Aspen Way • Vista, CA 92081 • USA
800-642-2155
Tempo Europe Ltd. • Brecon House, William Brown Close Cwmbran, NP44 3AB, UK
Tel: +44 1633 927 050
www.TempoCom.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>