elspet ELS407 Smart Cat Litter Box User Manual

elspet ELS407 Smart Cat Litter Box

Thank you for using elspet products.
For your safety and better use of this product, please read this user manual carefully.
Keep this manual properly for future use.

Product specification

Important note

• Pull the pedal out before use
• Adjust the time according to the actual situation
• Do not push the door
• Timely sand replenishment
• Don’t use long strips of tofu Kitty litter
• Do not expose yourself to ultraviolet rays for a long time
• Dispose of litter boxes in time
• Clean pedals, garbage boxes, inner doors, claws and sand basins regularly
• Use the 12V4A adapter. Do not use other adapters
• If you need to move or transport, please press shutdown and then power off

Preparation steps before use

(Mixed or bentonite cat litter less than 5mm in length is recommended)

1. Open the back door and take out the accessories
   

2. Put on the garbage bag
   

3. Move the pedal until you hear the beep
   

4. After the power is connected, there is a prompt tone
   

5. Unseal the door
   

6. Long press button 1 to power up
   

7. After the door is automatically opened, the cotton plug is installed on both sides of the body
   

8. Add Kitty litter
   

9. The amount of cat litter should not be too much or too little within the standard range
   

10. Standalone version is ready. If you need to connect to WiF), see the next page
    

Bind Elspet smart APP

Software installation method:

1. Scan the QR code on the right to download and install
2. Apple App Store search elspet
3. Google App Store search for Elspe

APP Connection Steps

1. Hold down the fuselage 1.2 at the same time

2. Connect WiFi in advance and open the app

3. Click add device

4. Select the litter box icon

5. Confirm that the indicator is blinking at short intervals

6. Enter the WiFi password

7. Wait for loading

8. Complete the connection

APP sand indicator and reset

Sand quantity reset method 1

• The initial sand content is green
• Turns yellow after 25 runs
• Turns red after 80 runs

*The initial sand quantity indicator is green, at this time, it is necessary to add an appropriate amount of cat litter in the sand basin, referring to the scale in the basin

If the sand amount is insufficient, please add sand in time, and click the sand amount reset button after adding sand

Confirm resetting the cat litter

Sand quantity reset method 2

APP Device Sharing

Detailed explanation of assembly method

1. Into the cat litter box (the litter box fills into the bottom groove)
   

2. Install the pedal according to the corresponding hole position
   

3. Press the buttons on both sides of the pedal and put it into the cat toilet
   

4. Install sponge plugs on both sides of the fuselage
   

5. D Press key 4 to lift the rake

6. Press the buttons on both sides of the rake to load
   

7. Install the inner door
   

8. Put garbage bags
   

Disassembling cleaning steps

1. Open the back door and take out the garbage bag

2. Remove the inner door cover

3. Press key 1 and then key 4

4. Wait for the rake to lift

5. Press and hold the button to remove the claw

6. Press and hold the button to remove the pedal

7. Press the bottom of the cat toilet and take out| the sand bowl
   

8. Cleaning components
   

Product Function Introduction

1. Button system
   

   • Button 1 : power switch: press to start; Long press shutdown; When the machine is on, press open manual feces shoveling
   • Button 2  Quiet sleep switch: the indicator light means open (in standby state at night), to the day automatic reply
   • Button 3 lamp ring switch: open can be used for lighting, off in the closed state, specific instructions see the next page
   • Button 4 : Mode button: On indicates that the switch is started
     Press once in the power-on state to increase the cat litter gathering time from 10 minutes to 20 minutes
     Press once in the off state to enter the cleaning mode

2. Time adjustment
   

3. Long press the 1  button, the hour hand flashes, and each press increases one hour.

4. Long press the 2 button, the minute hand flashes, and each press increases one minute.

Indicator ring diagram

• Blue light:
  Steady on: Standby
  Blinking slowly: Sterilization and deodorization

• Green light:
  Steady on: Ready mode
  Flashing: Start shoveling feces

• Red light:
  Steady on: pedal move
  Slow flash: Sand basin sticking bottom (need to clean by oneself)
  Flash: The machine is faulty

Ultraviolet sterilization instructions

After clearing the clumps, ultraviolet light turns on
Time: 20 minutes (APP adjustable time) It automatically stops when the pet enters the cabin

Induction system

When the electric door is closing, pet entry will immediately stop closing and re-open.

Common faults/solutions

1. If the cat enters the interior when the door is about to close, the fuselage will detect the cat and immediately stop the door and reopen it 10 seconds after the cat leaves and then operate again to complete cleaning.
2. When the cat litter is found stuck to the bottom, the rake will stop working and sound the alarm, return to the original position and enter the standby state. (The red light ring of the stand-alone version is on, and the blue light ring of the Wi-Fi version is on), it can be used normally after the next cleaning.
3. The reason for displaying the foreign body card may be the door close switch shrapnel falling/door deformation/door motor damage/cat litter sticking to the bottom/too much cat litter/rake deformation, etc., which will prompt the red or blue light flashing.
4. If the garbage bag near the sand bin is not covered properly, the rake will be stuck. Please check and adjust it in time

This device complies with Industry Canada license-exempt RSS standard( s).

Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device”

FCC Warning

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause un- desired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment.
This equipment should be installed and operatedwith minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>