Etekcity EKS-L422 Luminary Lite Kitchen Scale User Manual

Luminary™ Lite Kitchen Scale
User Manual

Thank you for purchasing the
Luminary™ Lite Kitchen Scale by
Etekcity.

EKS-L422 Luminary Lite Kitchen Scale

If you have any questions or concerns, please reach out to our helpful Customer Support Team at support@etekcity.com.
We hope you enjoy your new kitchen scale!

Package Contents

1 x Luminary™ Lite Kitchen Scale
1 x USB Type-C Charging Cable
1 x Quick Start Guide

Specifications

READ AND SAVE THESE INSTRUCTIONS

Important Safety Information

To avoid damage to this scale, please read and follow all instructions and safety guidelines in this manual.

Scale

• Do not exceed the 22 lb / 10 kg weight capacity, as it will damage the scale. An error indicator will appear on the LED display if the limit is exceeded.
• The scale is IPX6 water resistant, which means it can withstand most liquid spills without permanent damage. However, we still recommend wiping the scale dry with a soft cloth after any spills to keep it in optimal condition.
• Handle with care. This scale is not intended for commercial or heavy-duty use.
• Keep the scale in a cool, dry place. Avoid exposure to damp environments or extreme temperatures.
• Household use only.

Battery

When the scale is in use, will flash if the scale is running low on battery. The scale’s display will show “Lo” when the battery needs to be charged immediately. Follow the steps to recharge the battery.

1. Insert the USB charging cable into the USB charging socket.
2. Plug the USB charging cable into a DC 5V adapter and plug into an outlet. You can also plug the cable into a powered USB outlet.
3. When charging, will flash. Once the battery is fully charged, will stop flashing.

Note: The scale can’t be used while charging, so it is recommended to charge the battery when flashes, indicating low battery.

Function Diagram

A. LED Display
B. Unit Selection Button
C. Power/Zero Button| D. Hold Button
E. Anti-Skid Pads
F. USB Charging Port
---|---

Display Diagram

A. Battery Charging Indicator
B. Hold Indicator
C. Tare Indicator
D. Milk (Liquid)| E. Water (Liquid)
F. Measurement Unit
G. Weight Value
---|---

Using Your Scale

Note:

• For accurate results, always place the scale on a hard, flat surface, and keep the scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic interference.
• When you turn on the scale, choose units, or use the tare function, wait for the display to read “0.00” before measuring.

General Operation

1. Place the scale on a hard, flat surface.
2. Tap to turn on the scale. Make sure the display reads “0.00”. If the screen does not display “0.00” automatically, tap to adjust to zero.
3. Tap UNIT to select your desired measuring unit, which will show on the bottom of the display.
4. Place your item on the scale.
5. Wait for the reading on the display to stabilize.
6. When you’re done, reset the scale by removing all items from the scale. If the display doesn’t read “0.00”, press to reset the weight to zero.

Zero / Tare Function

Whenever you measure items inside a container, you can use the tare function to remove the container’s weight from the final measurement.

1. Tap to turn on the scale. Make sure the display reads “0.00”. If the screen does not display “0.00” automatically, tap to adjust to zero.
2. Place the container on the center of the scale.
3. Wait for the reading on the display to stabilize. The display will show the container’s weight.
4. Tap to tare the weight of the container. The screen will now display “0.00”.
5. Place the liquid or items into the container. The scale will measure the contents without including the weight of the container.
6. When you’re done, reset the scale by removing all weight and tapping again.

Unit Conversion
To change the unit of measurement, tap UNIT until the display shows your desired unit of measurement.

Hold Function
There are two ways to use the hold function:
a. Place your item on the scale. Tap HOLD to lock the measurement reading. Tap HOLD again to unlock the display.
b. Tap HOLD and place your item on the scale. Wait 3 seconds for the reading to stabilize. The scale will automatically lock the measurement reading. Tap HOLD again to unlock the display.

Note: In hold mode, will not work. You can still use UNIT to switch between units.

Automatic Power Off
To save battery power, the scale will automatically power off after 180 seconds of inactivity.
Manual Power Off
Press and hold for 2 seconds to turn off the scale.

Troubleshooting

power cord to charge.
Reading is inaccurate.| Place scale on a level surface.
Keep scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic interference.
Make sure the screen displays “0.00” before measuring (see Zero / Tare Function, page 10).
Battery Charging Indicator is flashing| When the scale is in use, will flash if the scale is running low on battery. Plug in the USB power cord to charge.
will flash when the battery is charging. Once the battery is fully charged, will stop flashing.
Display shows “Err”| Item is too heavy. Remove item from scale to protect its weight sensor. Use a different scale with a higher weight range.
Display shows “Lo”| The battery is out of power and needs to be charged immediately. Plug in the USB power cord to charge the scale (see Battery, page 6).

If your problem is not listed, please contact Customer Support (see page 16).

Federal Communication Commission Interference Statement – Part 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC SDOC SUPPLIER’S DECLARATION OF CONFORMITY
Etekcity Corporation hereby declares that this equipment is in compliance with FCC requirements. The declaration of conformity may be consulted in the support section
of our website, accessible from www.etekcity.com.

Warranty Information

For your own reference, we strongly recommend that you record your order ID and date of purchase.
Order ID|
Date of Purchase|

TERMS & POLICY
Etekcity Corporation (“Etekcity”) warrants this product to the original purchaser to be free from defects in material and workmanship, under normal use and conditions, for a period of 2 years from the date of original purchase.
Etekcity agrees, at our option during the warranty period, to repair any defect in material or workmanship or furnish an equal product in exchange without charge, subject to verification of the defect or malfunction and proof of the date of purchase.

There is no other express warranty. This warranty does not apply:

• If the product has been modified from its original condition;
• If the product has not been used in accordance with directions and instructions in the user manual;
• To damages or defects caused by accident, abuse, misuse or improper or inadequate maintenance;
• To damages or defects caused by service or repair of the product performed by an unauthorized service provider or by anyone other than Etekcity;
• To damages or defects occurring during commercial use, rental use, or any use for which the product is not intended;
• To damages or defects exceeding the cost of the product.

Etekcity will not be liable for indirect, incidental, or consequential damages in connection with the use of the product covered by this warranty.
This warranty extends only to the original consumer purchaser of the product and is not transferable to any subsequent owner of the product regardless of whether the product is transferred during the specified term of the warranty.
This warranty does not extend to products purchased from unauthorized sellers. Etekcity’s warranty extends only to products purchased from authorized sellers that are subject to Etekcity’s quality controls and have agreed to follow its quality controls.
All implied warranties are limited to the period of this limited warranty.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
If you discover that your product is defective within the specified warranty period, please contact Customer Support via support@etekcity.com.
DO NOT dispose of your product before contacting us. Once our Customer Support Team has approved your request, please return the product with a copy of the invoice and order ID.
Every Etekcity product automatically includes a 2-year warranty. To make the customer support process quick and easy, register your product online at www.etekcity.com/warranty.

This warranty is made by:
Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806

Customer Support

If you have any questions or concerns about your new product, please contact our helpful Customer Support Team.

Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Email: support@etekcity.com
Toll-Free: 855-686-3835
Support Hours
Mon–Fri,
9:00 am–5:00 pm PST/PDT

*Please have your order invoice and order ID ready before contacting Customer Support.

Connect with us @Etekcity

References

• Vesync-Warranty Registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>