PROSOLAR Hiway 15 PIR Motion Sensor Auto-Adjust Solar Light User Manual
- June 9, 2024
- PROSOLAR
Table of Contents
PROSOLAR Hiway 15 PIR Motion Sensor Auto-Adjust Solar Light User Manual
SPECIFICATIONS
- Wattage: 15w
- Lamp : In-built LED x 40 (SMD 2835)
- Colour Temperature: 6000K (Daylight White) / 3000K (Warm White)
- Lumen Output: 1600 lm
- LED Life Expectancy: up to 35,000 hours
- Max Illumination Time at Full Charge: up to 5 nights
- Sensor: PIR (Motion Sensor) + Photocell (Dusk to Dawn)
- PIR Distance: Up to 8m
- PIR Sensor Delay Time: approx. 20 seconds
- PIR Sensor Angle: 120 degrees
- Battery Type: Lithium Ion 18650 7.4v 5400mAh (Replaceable) – Total Capacity 10800mAh
- Battery Lifespan: up to 8 years
- Battery Charge Time: 10 -12 hours
- Solar Panel: 9.5Wp Polycrystalline Silicon – Lifespan up to 5 years
- IP Rating: IP65
- Materials: Aluminium, Polycarbonate, Tempered Glass
- Weight: 1950g (approx.)
- Mounting: Standard bracket, galvanised steel bracket & pole adaptor supplied
- Install Height: 2-5m recommended
- Functions: Auto Adjust – see modes / settings
WARNINGS
- If a fitting is found to be damaged, cease use immediately.
- The unit may get warm whilst on for a period of time.
- Always take care when installing your solar light, especially when mountingit in high places.
- Ensure the fitting is mounted out of range of head height to avoid injury.
- Fitting must be mounted to a solid surface.
- This Solar Light will not charge correctly if the panel is behind glass or artificial light is used.
- For replacement battery, contact the manufacturer.
CLEANING & MAINTENANCE
Occasional cleaning and care are recommended for this product. Wipe with a soft, slightly damp cloth to remove any surface dirt. To maintain efficiency, specifically clean the solar panel, LEDs and PIR on a regular basis. Also, keep the solar panel free of debris and snow to prevent reduced battery life or malfunction. Do not use abrasive cleaners or a lot of water as this could damage the fitting. Please refer to our website for more information on the best way to clean different materials.
RETURNS
If purchased from a 3rd party, please contact your supplier. If purchased direct, contact us by phone or email: Exterior Lights UK Ltd Tel: +44 1689 606342 Email: [email protected]
Our full returns policy is available on our website.
Waste Electrical Products should not be disposed of with household waste.
Please check with your local authority or contact us for more information.
Please recycle packaging whenever possible.
HIWAY 15 TECHNOLOGY
The Hiway 5 is a highly efficient solar light with high capacity Lithium Ion batteries and a fast charging Polycrystalline solar panel. This means that even on cloudy and rainy days, it will re-charge efficiently. The high battery capacity gives enough power for up to 5 nights when there is little light during the day. The 1600 lumen light output is bright enough to illuminate driveways and paths, making them safe to navigate at night
INSTALLATION
Designed to be mounted on a flat surface or right-angled post (40-50mm diameter) at a height of 2-5m. The higher the light is mounted, the larger the illuminated area.
Location – It is important that the installation location is carefully considered, avoiding shady areas. The best position is south facing, however the light can work facing in other directions, especially when in full sunshine. The PIR must face the direction in which the motion is to be detected. Ensure there is no other lights which could interfere with the Sensors, imitating daylight.
WALL MOUNTING
- Use the L shaped arm to mark the mounting holes on the mounting surface in the desired location.
- Drill the 2 x 8mm holes at a depth of 60mm and insert expanding anchor bolts (alternative mounting screws / plugs may be required depending on the surface).
- Slot the arm into the slit at the back of the Hiway fittings, replace the flat cover and secure in place with the socket screws, washers nuts and allen key provided (nuts fit inside hexagonal cut outs on the bottom of the fitting).
- Place the arm over the expanding anchor bolts pre-installed into the mounting surface, followed by the washer, spring washer and then secure in place with the nuts with a spanner, ensuring the bolts expand to lock in place.
LAMP POST / GALVANISED STEEL BRACKET ADAPTOR
- Remove the flat cover from the top back section of the fitting.
- Replace with the pole adaptor (semi-circle cut out) and attach very loosely with the screws and nuts provided (nuts fit inside hexagonal cut outs on the bottom of the fitting).
- Slot the pole adaptor and fitting over the right-angled pole / galvanized steel bracket until it is in the desired location and securely fasten in place by completely tightening the socket screws with the allen key provided.
NOTE: In order to prevent the hexagonal nuts from dropping out when removing the bolt, they are designed to remain inside the hexagonal cut outs of the fitting. To remove, loosely screw the bolt into the nut from the underside to pull out.
TIP: The Hiway can be surface mounted onto a 75mm or 100mm square post
(fence posts). Posts are best concreted 300-400mm into the ground.
MODES / SETTINGS
The Hiway is an auto-adjust, multifunction solar light. All modes will only function during darkness / dusk. The on button only needs to be pressed once for the auto-adjust multifunction to work continuously every night.
FIRST 5 HOURS: Constant on at 30% brightness. Full brightness when motion is detected within 8 metres. After 20 seconds of no motion being detected, the light will reduce back to constant light at 50% brightness.
AFTER 5 HOURS OR LESS THAN 30% BATTERY CAPACITY – Full brightness when motion is detected within 8 metres. Following 20 seconds of no movement being detected, the light will reduce to 50% brightness. After 5 minutes, the light will turn off until movement is detected again.
ON/OFF: Press the button next to the PIR Sensor once to turn on (auto adjust), and again to turn off completely
Full product range & more information: www.exteriorlights.co.uk