PROSOLAR Litecharga Professional Solar Bollard Light User Manual
- June 9, 2024
- PROSOLAR
Table of Contents
PROSOLAR Litecharga Professional Solar Bollard Light User Manual
SPECIFICATIONS
- Wattage: 1.8W
- Lamp: In-built Epistar LED Chips 10 *18 mil (120˚ Beam Angle)
- Colour Temperature: 3000K (Warm White) / 6000K (Daylight White)
- Lumen Output: 210 lm
- LED Life Expectancy: up to 50,000 hours
- Sensor: Light / Charge Sensor
- IP Rating: IP65
- Battery Type: Lithium – LiFePO4 6.4v/5000mAh (replaceable)
- Battery Charge Time : 6-8 hrs full sunshine (approx.)
- Max Illumination Time at Full Charge : Up to 23hrs
- Solar Panel: 9v / 3.5W Monocrystalline Solar Panel – Grade A
- Materials: 6063 Die Cast Aluminium & High Impact Polycarbonate
- Weight: 5KG (approx.)
- Mounting: Internal Surface Mount (supplied)
- Lighting Function: 1hr 100% + 2hrs 80% + 2hrs 50% + 9hrs 30%
- Working Temperature: -25˚C ~ 55˚C
- Included: Bollard, Internal Mount, Rubber Bung
WARNINGS
- If a fitting is found to be damaged, cease use immediately.
- The unit may get warm whilst on for a period of time.
- Always take care when installing your solar light.
- Fitting must be mounted to a solid surface or using relevant anchor bolts / J Bolts
- This Solar Light will not charge correctly if the panel is behind glass or artificial light is used.
- Ensure the waterproof bung is in place at all times, other than when turning the unit on.
- Due to temperature difference in and outside the fitting, condensation may be present internally but will not affect use.
Dimensions
CLEANING & MAINTENANCE
Occasional cleaning and care are recommended for this product. Wipe with a soft, slightly damp cloth to remove any surface dirt. To maintain efficiency, specifically clean the solar panel and polycarbonate lens on a regular basis. Also, keep the solar panel free of debris and snow to prevent reduced battery life or malfunction. Do not use abrasive cleaners or a lot of water as this could damage the fitting. Please refer to our website for more information on the best way to clean different materials.
RETURNS
If purchased from a 3rd party, please contact your supplier. If purchased direct, contact us by phone or email:
Exterior Lights UK Ltd
Tel: +44 1689 606342
Email: sales@exteriorlights.co.uk
Our full returns policy is available on our website.
Waste Electrical Products should not be disposed of with household waste. Please check with your local authority or contact us for more information. Please recycle packaging whenever possible.
Producer Registration Numbers: WEE/KC3440XY / BPRN0843
Full product range & more information: www.exteriorlights.co.uk
LITECHARGA TECHNOLOGY
The Litecharga is a highly efficient solar light with high capacity LiFePO4 Lithium batteries and a fast charging Monocrystalline solar panel. This means that even on partially cloudy and rainy days, it will re-charge efficiently. The high battery capacity gives enough power for up to 23 hrs solid light (approx. 2-3 night) even when there is little light during the day. The high lumen light output is bright enough to illuminate driveways and paths, making them safe to navigate at night.
INSTALLATION
The Litecharga is designed to be mounted on a low wall, patio, wood or set in concrete (J-Bolts – sold separately) via the internal surface mount.
Recommended spacing is 3m apart for substantial path lighting. Closer spacing / staggering will result in a more intense light
Location – It is important that the installation location is carefully considered, avoiding shady areas. Ensure there is no other lights which could interfere with the light, imitating daylight and forcing the light off.
- To surface mount, remove the internal base from the bollard by unscrewing the 3 x cross head screws at the bottom of the bollard tube, then lift off.
- Use the base to mark the mounting holes on the mounting surface.
- Remove the mounting plate and drill out the 3 holes marked at the relevant depth and diameter for the mounting screws / wall plugs being used (varies based on mounting surface) – Anchor bolts recommended.
- Secure the mounting base in place – large washers may be required.
- Replace the bollard body, lining up the 3 x holes at the base.
- Replace the 3 cross head screws removed in point one to secure in place.
For root mounting, use J-Bolts, set in concrete instead of anchor bolts (sold separately).
SETTINGS
The Litecharga has a pre-set time controlled setting which cannot be changed. At dusk, the bollard will illuminate at full brightness, and then follow a gradual dimming sequence until it reaches 30% brightness after 5 hours. From then on it will remain at 30% until dawn. This sequence is to ensure maximum charge is retained.
IMPORTANT – SOLAR BOLLARD MUST BE TURNED ON AT ALL TIMES AFTER INSTALLATION
If the bollard is left in the off position, you may be prompted to turn the fitting on by strobing. Solar bollard will only charge when in the ON position.
Turning on the bollard
- Remove the waterproof rubber bung located just below the polycarbonate lens, in line with the Lumena Logo, to locate the red on/off button.
- Using a small, flathead screwdriver (or similar), push the on button inwards until it clicks and allow to pop back out (this will be partial). The bollard is now in the ON position.
- Replace the waterproof, rubber bung
NOTE: There will be a 2-5 second delay between turning the solar light on, and the bollard illuminating. In daylight, the light will turn back off within a few seconds, in darkness it will remain on and follow the time controlled cycle.
STORAGE
When storing the bollard, be sure to turn the bollard to the off position by following the above steps (check by covering and uncovering the solar panel). Once pressed, the on/off button will release fully forward. Maximum 6 months storage when fully charged – recharge will be required periodically to prevent damage to battery over long periods of time.
Full product range & more information: www.exteriorlights.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>