X-SENSE SWS51 Smart Water Leak Detector User Manual

X-SENSE SWS51 Smart Water Leak Detector User Manual

This user manual contains important information about the operation of your water leak sensor. To ensure proper use and trouble-free operation, please read this manual carefully and store it in a safe place for future reference.

Introduction

This water leak sensor sounds an alarm whenever it comes into contact with water. It can be placed near common household water sources like a dishwasher, hot water heater, or washing machine. With professional monitoring, you will be notified if your home is in danger.

Produd Overview

Package Contents

Operating Your Device

Activating the Device

Press and hold the Activate button for 3 seconds. When the red LED flashes once and the alarm sounds one beep, then the product is activated and enters the normal working status.

Testing the Device

After the device is activated, you must test the device to ensure it is operating normally. Press the Test button at the bottom of the device. The alarm will deliver 3 beeps paired with the red LED flashing. The sound will automatically stop after the test is completed.

Water Leak Detection

This water leak sensor is used to detect water leaks and floods. Once a water leak occurs, the device will sound an alarm continuously paired with a flashing red LED. If the user takes no action at this time, the device will continue to sound an alarm until the battery runs out.

SIiencing the Device

When the device is triggered, press the Silence button to mute the alarm, which will last for 10 seconds. After 10 seconds, the device will continue to sound an alarm. To disable the alarm, you must completely clean and dry the surface of the device.

Installing Your Device

Installation Location

You can use the device near places where water leaks are likely to occur such as near water pipes, basement sump pumps, dishwashers, washing machines, toilets, water heaters, window wells, etc.

Installation Method

This sensor can simply be placed on a fiat surface.

Note

1. Do not place the device upright, othe,wise no alarm will be triggered.
2. Do not place the device on uneven surfaces as this may cause false alarms.

Battery Replacement

When the battery is low, the red LED will flash once every 60 seconds paired with one beep to remind the user to replace the batteries. To replace the batteries, remove all screws, take out the used batteries and replace with two new AAA batteries. Then, reinstall the screws and press and hold the Activate button for 3 seconds to activate the device. Then test the device once again.

Note: After replacing the battery, you need to align the positioning points of the upper and lower cases to close the cover and then screw the device closed.

WARNiNG

1. Keep the device operating at a temperature between 32-122°F (0-50°O and humidity below 90% RH.
2. Do not disassemble the device by force. Otherwise, the device may become damaged.

Technical Specifications

Troubleshooting

|
---|---
The device does   The device is| Check   whether the device is
not work.It is| not activated.| activated. The device needs to be
not triggered| | activated before it is used for the
when there is a| | first time. Otherwise, the device
water leak.| | will not be triggered (refer to
| | ·Activating the Device· section).
| | Upon activation, press the Test
| | button to make sure it is
| | operating properly.
| The battery is| Please check whether the battery
| low.| power is sufficient. When the
| | battery is low, the red LED will
| | flash once every 60 seconds
| | paired with one beep. Please
| | replace the battery immediately.
The alarm   sound is low.| Water   entered   the  alarm.| The device is waterproof and its   performance will not be affected if water gets inside.   Please take the device in your   hand and shake it a few times to remove   the water from the alarm opening until   the alarm sound returns to normal. Then   put the device back.
---|---|---

Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities are available. Please check with your local authorities or retailers for recycling advice.

Manufacturer and Service Information

X-Sense Innovations Co., Ltd.
Address : 84-503, Kexing Science Park 15 Keyuan Road, Shenzhen, 518057, CHINA
Email : support@x-sense.com

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>