innovair IA60002 Remote Control User Manual
- June 9, 2024
- innovair
Table of Contents
innovair IA60002 Remote Control User Manual
Remote controller
-
1. The remote controller transmits signals to the system.
ON/OFF BUTTON
The appliance will be started when it is energized or will be stopped when it is in operation, if you press this button. -
2. MODE BUTTON
Press this button to select the operation mode. -
3. FAN BUTTON
Used to select fan speed in sequence auto, higher, high, medium, low or lower. -
4,5. ROOM TEMPERATURE SETTING BUTTONS
Used to adjust the room temperature and the timer, also real time. -
6. SMART BUTTON
Used to enter fuzzy logic operation directly, regardless of the unit is on or off. -
7. SLEEP BUTTON
Used to set or cancel Sleep Mode operation. -
8. SWING BUTTON
Used to stop or start vertical adjustment louver swinging and set the desired up/down airflow direction. -
9. IFEEL BUTTON
Used to set IFEEL mode operation. Press it once, the IFEEL function will be started. Press it again, the IFEEL function will be shut off. -
10. CLOCK BUTTON
Used to set the current time. -
11,12. TIMER ON/OFF BUTTON
Used to set or cancel the timer operation. -
13. SUPER BUTTON
Used to start or stop the fast cooling/heating. (Fast cooling operates at high fan speed with 61 °F(16°C) set temp automatically ; Fast heating operates at auto fan speed with 86°F(30°C) set temp automatically.) -
14. DIMMER BUTTON
When you press this button, all the display of indoor unit will be closed. Press any button to resume display. -
15. SWING BUTTON
Used to stop or start Horizontal adjustment louver swinging and set the desired left right airflow direction. -
16. MUTE BUTTON
Used to stop or start MUTE Mode operation. Fan speed is automatically set at lower fan speed. -
17. 8° HEAT BUTTON
Used to set 8° heating mode.
Indication symbols on LCD:
Operation instructions
-
How to Insert the Batteries
Remove the battery cover according to the arrow direction.
Insert new batteries making sure that the(+) and(-) of battery are matched correctly.
Reattach the cover by sliding it back into position.
Note: -
Use 2 LR03 AAA(1.5volt) batteries. Do not use rechargeable batteries.
Replace batteries with new ones of the same type when the display becomes dim. -
Storage and Tips for Using the Remote Controller
The remote controller may be stored mounted on a wall with a holder.
Note: The remote controller holder is an optional part.
- How to Use
To operate the room air conditioner, aim the remote controller to the signal receptor. The remote controller will operate the air conditioner at a distance of up to 7m when pointing at signal receptor of indoor unit.
⚠ CAUTIONS
For appropriate signal transmission between remote controller and indoor unit,
keep the signal receiver away from the following items:
• Direct sunlight or other strong lights or heat
• Flat panel television screen or other electrical appliances that react to
the remote controller Additionally, the air conditioner will not operate if
curtains, doors or other materials block the signals from the remote
controller to the indoor unit. If the signal may not be transmitted properly,
either move these materials or consult your local dealer.
Operation modes
Note: Press and hold “MODE” button and ” G ” button together for 3 seconds
will alternate the temperature display between the °C and °F scale.
Note: Heating mode is NOT available for cooling only models.
Note: At “Dry” mode, the unit can decrease or rise 7″F by remote controller if
you feel uncomfortable.
Press button, when the appliance receives the signal, the RUN indicator of the indoor unit lights up.
SWING, SMART, TIMER ON, TIMER OFF, CLOCK, 8° HEATING, SLEEP and SUPER operation modes will be specified in the following pages.
- Changing modes during operation, sometimes the unit does not response at once. Wail 3 minutes.
- During heating operation, air flow is not discharged at the beginning. After 2-5 minutes, the air flow will be discharged until temperature of indoor heat exchanger rises .
- Wait 3 minutes before restarting the appliance.
Airflow direction control
NOTE: lf the unit doesn’t have four ways airflow function, you can adjust horizontal airflow by yourself.
Do not turn the vertical adjustment louvers manually, otherwise malfunction
may occur. If that happens, turn off the
unit first and cut off the power supply, then restore power supply again.
It is better not to let the vertical adjustment louver tilt downward for a
long time at COOLING or DRY mode to prevent condensed water from dripping.
SMART mode
Press the SMART button, the unit enters SMART mode(fuzzy logic operation) directly regardless of the unit is on or off. In this mode, temperature and fan speed are automatically set based on the actual room temperature.
TIMER mode
It is convenient to set the timer on with TIMER ON/OFF buttons when you go out in the morning to achieve a comfortable room temperature when you get home. You can also set the timer off at night to enjoy a good sleep.
► How to set the TIMER ON
The TIMER ON button can be used to set the timer to switch on the appliance at your desired time.
i) Press the TIMER ON button and when “ON 12:00” flashes on the LCD display, you can then press the 0 or 0 buttons to select the time you wish for the appliance to turn on.
Press the 0 or 0 button once to increase or decrease the time setting by 1
minute.
Press the 0 or 0 button 2 seconds to increase or decrease the time setting by
10 minutes.
Press the 0 or 0 button for a longer time to increase or decrease the time by
1 hour.
Note: If you don’t set the time in 10 seconds after you press the TIMER ON button, the remote control will exit the TIMER ON mode automatically.
ii) When your desired time is displayed on the LCD, press the TIMER ON button
and confirm it.
A “beep” will sound. “ON” stops flashing.
The TIMER indicator on the indoor unit lights up.
iii) After the set timer is displayed for 5 seconds the clock will be
displayed on the LCD of the remote control.
► How to cancel TIMER ON
Press the TIMER ON button again. Once you hear a “beep” and the indicator
disappears, the TIMER ON mode has been canceled.
Note: It is similar to set TIMER OFF. You can make the appliance switch off
automatically at your desired time.
8° HEATING mode
• 8°HEAT button is used to set 8°C heating mode.
In 8°HEATING mode, the fan speed is set at “AUTO” automatically.
• The 8°HEATING mode will be started when you press 8°HEAT button at the
heating mode.
■ If you press any button except for TIMER ON, TIMER OFF, CLOCK, IFEEL and
SWING button, you can escape from 8°HEATING mode. Then the display a· will
disappear and the 8°HEATING mode will be cancelled.
Note:
In 8°HEATING mode, the default temperature is set 8°C.
8°HEATING mode can be set only when the air conditioner works in the heating
mode.
SUPER mode
■ SUPER mode is used to start or stop fast cooling or heating. In SUPER mode,
the super indicator @ will display on LCD.
Fast cooling operates at high fan speed, changing the set temperature
automatically to 61 °F(16°C); Fast heating operates at auto fan speed,
changing the set temperature automatically to 86 °F(30°C).
• SUPER mode can be set when the appliance is in operation or energized.
■ In SUPER mode, you can set temperature, airflow direction or timer. If you
want to escape from SUPER mode, press SUPER, MODE, FAN, ON/OFF or SLEEP
button, the display will return to the original mode.
Note:
- SMART button is not available in SUPER mode.
- The Appliance will continue working in SUPER mode , if you don’t escape from it by pressing any of the buttons mentioned above.
- Heating is NOT available for cooling only air conditioner.
- For the first generation of products, you can’t set temperature in super mode, but you can press TEMPERATURE SETTING button to escape super mode.
SLEEP mode
SLEEP mode can be set in COOLING ,HEATING or DRYING mode. This function gives
you a more comfortable environment for sleep.
• The appliance will stop operation automatically after operating for 8 hours.
■ Fan speed is automatically set at low speed. Each time SLEEP button is
pressed, the operation mode is changed in sequence:
SLEEP 1 . SLEEP 2 . SLEEP 3 . SLEEP 4 . QUIT SLEEP MODE
SLEEP mode 1:
■ Set temperature will rise by 2°F(2°C) at most if the appliance operates in
cooling mod for 2 hours constantly, then keeps steady.
■ Set temperature will decrease by 2°F(2°C) at most if the appliance operates
in heating mode for 2 hours constantly, then keeps steady.
SLEEP mode 2:
■ Set temperature will rise by 2°F(2°C) if the appliance operates in cooling
mode for 2 hour constantly, decrease by 1 °F(1 °C) after 6 hours, then
decrease by 1 °F(1 °C) after 7 hours.
• Set temperature will decrease by 2°F(2°C) if the appliance operates in
heating mode for hours constantly, rise by 1 °F(1 °C) after 6 hours, then rise
by 1 °F(1 °C) after 7 hours.
SLEEP mode 3:
■ Set temperature will rise by 1 °F(1 °C) if the appliance operates in cooling
mode for 1 hour, rise by 2°F(2°C) after 2 hours, then decrease by 2°F(2°C)
after 6 hours, decrease by 1 °F(1 °C) after 7 hours.
■ Set temperature will decrease by 2°F(2°C) if the appliance operates in
heating mode for 1 hour , decrease by 2°F(2°C) after 2 hours, then rise by
2°F(2°C) after 6 hours, rise by 2°F(2°C) after 7 hours.
SLEEP mode 4:
■ Set temperature will keeps steady.
Note: Heating is NOT available for cooling only air conditioner.
Note: Press SUPER ,SMART, MODE,SLEEP or FAN button cancel SLEEP mode.
IFEEL mode
In IFEEL mode, the temperature sensor built in remote controller is activated. It can sense its surrounding temperature, and transmit the signal back the unit, the unit can adjust the temperature so as to provide maximum comfort.
Note: When using /FEEL mode, advice to put the remote in the place where the
indoor unit can receive the signal easily.
Note: When stopping the air conditioner, advice to cancel the /FEEL mode so as
to save energy .
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>