Lucci LEDlux 170760 CITY III Fixed 3CCT Downlight Installation Guide

170760 CITY III Fixed 3CCT Downlight
Installation Guide

Installation Instructions
CITY III FIXED 3CCT DOWNLIGHT
SKU# 170760, 170761, 170762, 170763
Rated Voltage 220-240V~ 50Hz

170760 CITY III Fixed 3CCT Downlight

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this luminaire. Please keep instructions for future reference.

Warranty

• This recessed luminaire is covered by a 5-year warranty valid for in-store replacement or refund only.
• The warranty period starts from the date of purchase, not the date of installation. Please retain the proof of purchase.
• The use of non-compatible dimmers may damage your recessed luminaire and will void your warranty.
• Warranty will be void if there is any damage due to improper usage or modification to the recessed luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• Before the installation, check the installation location in the ceiling has access to a socket outlet which is connected to a wall light switch and dimmer. If it does not, please contact a licensed electrician to arrange installation of the socket outlet, wall light switch and dimmer before continuing.

• All wiring and installation of the recessed luminaire must adhere to latest local and national wiring rules. e.g. AS/NZS 3000 Electrical installations. If unsure, please contact a licensed electrician.

• Only the front cover of the LED downlight is rated IP44 after it is fully installed. This must be maintained during installation. NOTE: The recessed parts of the LED downlight are rated IP20.

• Select a suitable location for installation:
  – The mounting point must support 2 times the weight of the recessed luminaire.
  – This recessed luminaire is suitable for indoor or outdoor use, provided that it is installed under cover or under eaves.

• NOTE: The colour shifting function will only operate with a mechanical or relay ON/OFF switch.

• NOTE: The colour shifting function will not operate with a semi-conductor ON/OFF switch (e.g. smart switch) or a dimmer with built in ON/OFF switching function (e.g. smart dimmer). An additional mechanical or relay ON/OFF switch is required on the same circuit with the semi-conductor ON/OFF switch or the dimmer with ON/OFF switching function with the downlight.

• This recessed luminaire is dimmable and was tested with the dimmers listed in the specification table at the date of publication.

• The use of a LED dimmer such as the Lucci LEDlux SKU# 290998*, 290997, 299043, 290989, 290992, 290993, 290994 or Buster + Punch DIM-002 dimmer is highly recommended.
  *NOTE: When using the SKU# 290998 dimmer, a minimum of 2 downlights must be connected, otherwise there may be slight glow from the single downlight when it is turned off.
  NOTE: For the best dimming range, use with the Lucci LEDlux SKU# 290998 dimmer and adjust the variable resistor at minimum and maximum dimming positions on the dimmer during the installation.

• NOTE: Dimming may cause buzzing sounds or a slight flicker. There may be slight delays with the LED light start up or slight uneven light performance when more than one LED light fitting is linked together, switched ON or dimmed. This is not a product fault and as such is not covered under warranty.
  NOTE: Some dimmers have a minimum load of 20W. Ensure the dimmer position is on the maximum setting before turning on the LED light and adjust the dimmer down to your desired light level.
  NOTE: Testing cannot account for installation variables such as variation in mains supply voltage, cable capacitance, electrical noise, transients, surges and ripple control signals (commonly found in NSW & QLD).
  NOTE: The information provided is correct to the best of Beacon Lighting’s knowledge at the date of publication.

• This recessed luminaire has an insulating ceiling type IC-4 rating. Building insulation material can safely be exposed continuously to temperatures up to 90°C may abut and cover the luminaire. (Please refer to the Clearance Information section and the IC-4 rating section in this instruction manual for further details.)

• If loose fill insulation or thermal insulation is not fixed into position or if there are loose combustible materials (e.g. leaves or combustible materials stored in the roof space), a barrier or guard is required as per the Clearance Information section in this instruction manual.

• The LED driver must be placed at least 100mm away from the LED downlight module to allow for cooling.

• The LED driver can be placed under the insulation. (Please refer to the Clearance Information section in this instruction manual for further details.)

• The LED downlight module is only suitable for use with Lucci LED Driver model#: LB-PD-2621-11.5W.

• The recessed luminaire must not be used if the diffuser has been cracked or damaged.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

• Lay out all the components on a smooth surface and make sure no components are missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the recessed luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
   NOTE: Before the installation, plug the downlight into a socket outlet to ensure it is working correctly.

2. Cut an installation hole of Ø 90mm into the ceiling. (Figure 1)

3. Insert the plug into the socket outlet and ensure it is fully plugged in. (Figure 2)

4. Push the springs up and put the LED downlight up through the cut-out hole and into the ceiling. (Figure 3)

5. Ensure all the clearance values are maintained during and after installation of the LED module, LED driver, thermal insulation, loose fill insulation, loose combustible materials and any structural members. (Figure 4)
   NOTE: Please refer to the Clearance Information section and the IC-4 section in this instruction manual for further details. Keep the LED driver 100mm away from the recessed luminaire to allow for cooling.

6. After the installation, switch on the recessed luminaire and enjoy your new lighting product.

7. To operate the colour shifting function, use the wall switch.
   – While the luminaire is on, toggle the wall switch OFF and ON again within 3 seconds.
   – The colour shifting sequence will jump from 3000K ­ 5000K ­ 4000K.
   – For the colour shifting to memorise the colour temperature, leave the wall switch OFF for over 7 seconds.
   To reset the colour shifting, toggle the wall switch OFF and ON twice within 1 second. Repeat if it doesn’t reset.
   NOTE: The colour shifting function will only operate with a mechanical or relay ON/OFF switch.
   NOTE: The colour shifting function will not operate with a semi-conductor ON/OFF switch.
   

Clearance Information ­ AS/NZS 3000:2018 Wiring Rules – Figure 4.9

any structural members, building elements or objects above it.
SCB| 0 mm (Minimum)| Clearance between the side of the recessed luminaire and any structural members, building elements or objects.
SCI| 0 mm (Abutted)| Insulation can be abutted against the side of recessed luminaire and covered as per IC-4 Rating. See IC-4 Rating section for more details.
SCG| 100mm| Auxiliary equipment/driver/transformer must be placed 100mm away from the luminaire. It can be placed under the thermal insulation and covered.

IC Rating ­ AS/NZS 60598.2.2: 2016

1. A closed luminaire that allows building insulation to come into contact with its sides and to cover it.
2. Type IC-4 recessed luminaire can be used together with building insulation that can safely be exposed continuously to temperatures up to 90°C may abut and cover the luminaire;
3. The declared IC-4 rating is based on the default testing ambient temperatures 25°C according to the standard.
   RISK OF FIRE ­ Required clearance from structural members and building elements
   SCB = 0 mm
   HCB = 0 mm

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning or making any adjustment to the luminaire.
• The recessed luminaire must not be used if the diffuser/protective shield has been cracked or damaged.
• The external flexible cable or cord of this recessed luminaire cannot be replaced; if the cable or cord is damaged, the recessed luminaire shall be destroyed.
• The light source of this recessed luminaire is not replaceable; when the light source reaches its end of life the whole recessed luminaire shall be replaced. There are no serviceable parts, do not attempt to dismantle or open the product.
• To avoid injury or damage to the recessed luminaire, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• To clean, wipe with a soft damp clean cloth. Do NOT soak or immerse the product in water or other liquids.
• Ensure the recessed luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.

Specifications

4000K – 1050 lumens
5000K – 1000 lumens| 3000K – 850 lumens
4000K – 1000 lumens
5000K – 950 lumens| 3000K – 850 lumens
4000K – 1000 lumens
5000K – 950 lumens| 3000K – 900 lumens
4000K – 1050 lumens
5000K – 1000 lumens
Highly Recommended
Dimmers| Lucci LEDIux SKU# 290998*, 290997, 299043, 290989, 290992, 290993, 290994Buster + Punch DIM-002.
Compatible Dimmers| Clipsal PDL354RDMLED-VW, 31E2RUDM, 32E450TM, 32E450UDM, 32ELEDM.
HPM Cat. 400T
Weight| 0.4kg
Cut-out Size| 090mm
IP Rating| IP20 for the back of the LED downlight (recessed parts)
IP44 for the front cover of the LED downlight (after installation)
Dimensions| H:63mm Dia:100mm
Driver Model #| LB-PD-2621-11.5W

• NOTE: The colour shifting function will only operate with a mechanical or relay ON/OFF switch. The colour shifting function will not operate with a semi-conductor ON/OFF switch (e.g. smart switch) or a dimmer with built in ON/OFF switching function (e.g. smart dimmer). An additional mechanical or relay ON/OFF switch is required on the same circuit with the semi-conductor ON/OFF switch or the dimmer with ON/OFF switching function with the downlight.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>