TOPDON TCView Thermal Camera for Android User Manual
- June 9, 2024
- TOPDON
Table of Contents
TOPDON TCView Thermal Camera for Android
Cautions
Read all instructions before use.
- Do not point the infrared camera at the sun or other strong energy sources for long periods of time. This may cause damage to the detector in the camera.
- Please keep the unit away from water to avoid leakage or short circuit.
- Do not touch the lens with your hands. Do not knock, pry, puncture, or scratch the lens.
- Do not disassemble the unit.
What’s in the Box
Product Overview
Using TC002 with an iOS Device
Preparation
- Download and install the TC002 app Go to APP Store and search TC002.
- Connect the TC002 camera to your iPhone or another iOS device that contains a lightning port. Plug the TC002 into your iOS device directly (see figure 3.1.1).
Or you can use the supplied extension cable to connect the TC002 to your iOS device (see figure 3.1.2).
Note:
- If you are using the supplied extension cable, make sure you connect the cable female side to TC002 before connecting the cable male side to the iOS mobile device.
- The iOS device should be equal to or greater than iOS 11 or iPhone 7.
- Open the TC002 app. The icon at the top right of the home screen displays “Connected” (see figure 3.1.3).
Make sure the camera and storage permissions are enabled for the TC002 app before use.
Thermal Imaging
Taking Photo/Video
- At the bottom of the bar, tap to enter the photo/video recording screen.
- Tap the camera button in the center of the bottom of the screen to take and save a snapshot.
- Tap the record button in the lower right of the screen to switch to video mode. Tap again to start and stop recording.
- To view the saved images/videos, tap on the thumbnail in the lower left corner (see figure 3.2.1).
Adding/Removing Measurement Tools
- At the bottom bar, tap to display measurement tool selections.
- Select to add a point of reference.
- Select to add a line (for hot spot and cold spot detection).
- Select to add a plane (for hot spot and cold spot detection).
- Select add a center spot, hot spot, and cold spot detection over the entire image area.
- Select to remove all measurement tools.
Changing Color Palette
This function allows users to change the pseudo-color display of the infrared image.
Follow the steps below to change the color palette:
- Tap at the bottom bar.
- Swipe right or left to select the desired palette.
Image Setting
- Tap to enter the image setting menu.
- Tap to rotate the image.
- Tap to adjust the image’s sharpness.
- Tap to adjust the image contrast.
- Tap to open the camera of your phone and enable Image in Image mode.
- Tap to enter DIY mode. Then, enter the lower and upper-temperature limits. You can also change the color display of areas where the temperature is out of the limits.
Temperature Range Setting
To better display the details of the object, please select an appropriate temperature range according to the expected temperature of the object you are inspecting.
- Tap to display temperature range options.
- Select Automatic Recognition/-20~150℃ (-4~302 ℉ )/150~550℃ (302~1022 ℉ ) according to your actual needs.
Temperature Monitoring
In this module, real-time temperature data can be displayed in a graph, allowing users to intuitively observe data changes.
- Tap “Generate Image”, and select the desired monitoring type as prompted. Then, select the place to be monitored on the screen.
- Tap “Start Recording”. The real-time temperature of the measured object will be displayed in a graph.
Gallery
To view the captured images and videos, tap “Gallery” on the home screen,
or select the thumbnail image on the photo/video recording screen to access
the Gallery.
Temperature Correction
To ensure the accuracy of measurement in different scenarios, this module
allows users to set Ambient Temperature, Distance to Spot, and Emissivity in
default mode, or add custom modes and set the corresponding parameters. 9
commonly used emissivity values are listed on the screen for reference. Please
go to “Personal Information” and tap “Temperature Correction” to enter the
setting screen.
Specifications
- Spectral Range: 8~14μm
- Resolution: 256×192 pixels
- Pixel Size: 12μm
- NETD: ＜ 50mK at 25°C, F#1.0, 25Hz
- Frame Rate: 25Hz
- Object Temperature Range: -20~150°C (-4~302°F), 150°C~550°C (302~1022°F)
- Accuracy: ±2ºC or ±2% of reading, the larger value shall prevail
FAQ
Q: Why is there no response after connecting the TC002 to my iOS mobile
device?
A: Follow the below steps to identify the problem:
- Check if the version of your iOS mobile device is equal to or greater than iOS 11 or iPhone 7.
- Check if you have downloaded the TC002 app and give the necessary authorization.
- Unplug the TC002 and reconnect it. If there is still no response, please contact after-sales personnel.
Q: Why is the TC002 device not working after I use the supplied extension
cable to connect TC002 and my iOS mobile device?
A: Make sure you connect the cable female side to TC002 before connecting
the cable male side to the iOS mobile device. If you don’t follow the steps in
order, the TC002 device may not be recognized.
Q: Can the TC002 detect objects underwater, through glass, or a wall?
A: No. Infrared detectors mainly detect the long-wave infrared region of
8~14μm, and can only be used to measure surface temperature.
Q: Why does the temperature reading increase when the device gets closer to
the object?
A: Infrared radiation attenuates when passing through the atmosphere. The
longer the distance, the greater the attenuation. Thus, the accuracy of
temperature measurement at a distance will decrease. To ensure the accuracy of
measurement, please go to Personal Information – Settings – Temperature
Correction – Distance to Spot, and input the actual distance (max: 5m) to get
the corrected temperature.
Q: Is the TC002 compatible with Android devices?
A: No. The TC002 is ONLY compatible with iOS mobile devices.
Q: While I’m using the thermal imaging function, why is there a clicking
sound with a frozen screen, once every few dozen seconds?
A: As the temperature of the infrared imaging camera changes slightly during
use, to ensure measurement accuracy, a periodic internal temperature
calibration is needed every a few dozen seconds. The micro-motor-controlled
activation or deactivation of such internal calibration makes a clicking sound
during which the screen freezes for about one second. To turn off the internal
calibration function, please open the TC002 app, go to Personal Information,
and turn off the Auto shutter.
Q: What external factors will affect the infrared temperature measurement?
A: The factors are as follows:
- The emissivity of the target object surface.
- Ambient temperature: the object will reflect the infrared rays emitted by surrounding objects, which affects the temperature measurement of the object itself.
- Atmospheric temperature: the atmosphere also emits infrared rays.
- Atmospheric transmittance: the infrared rays emitted by the object are attenuated in the atmosphere.
- Distance: the longer the distance, the greater the attenuation of the infrared rays emitted by the object in the atmosphere.
Warranty
TOPDON’s One-Year Limited Warranty
TOPDON warrants to its original purchaser that the company’s products will be
free from defects in material and workmanship for 12 months from the date of
purchase (Warranty Period). For the defects reported during the Warranty
Period, TOPDON will either repair or replace the defective part or product
according to its technical support analysis and confirmation. TOPDON shall not
be liable for any incidental or consequential damages arising from the
device’s use, misuse, or mounting. If there is any conflict between the TOPDON
warranty policy and local laws, the local laws shall prevail.
This limited warranty is void under the following conditions:
- Misused, disassembled, altered, or repaired by unauthorized stores or technicians.
- Careless handling and/or improper operation.
Notice:
All information in this manual is based on the latest information available at
the time of publication and no warranty can be made for its accuracy or
completeness. TOPDON reserves the right to make changes at any time without
notice.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note:
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
- These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from the one connected to the receiver.
- Consult a dealer or an experienced radio/TV technician for help.
Contact Information
- TEL
- 86-755-21612590
- 1·833-629-4832 (NORTH AMERICA).
- EMAIL: SUPPORT@TOPDON.COM.
- WEBSITE: WWW.TOPDON.COM.
- FACEBOOK: @TOPDONOFFICIAL.
- TWITTER: @TOPDONOFFICIAL.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>