Lazerlamps VOLVO V90-S90 2016+ Bumper Beam Mounting Kit Owner’s Manual
- June 9, 2024
- LAZERLAMPS
Table of Contents
Lazerlamps VOLVO V90-S90 2016+ Bumper Beam Mounting Kit
WHAT’S INCLUDED
- 2x Linear Side Bracket Kit
- M6 Fasteners
ALSO REQUIRED
- 1x Linear-18 (Standard, Elite or Elite with i-LBA)
- 1x One-Lamp Harness
DIFFICULTY LEVEL
TOOLS REQUIRED
-
PLASTIC TRIM TOOL SET
-
WIRE CUTTERS
-
WIRE STRIPPERS AND RATCHET CRIMPERS
-
TORX 25 SCREWDRIVER
-
TAPE MEASURE
-
SOCKET SET
-
ALLEN KEY SET
-
DRILL BIT
SWITCH – 20MM
INSTALL – 6.5MM
-
CABLE TIES
PRE-INSTALLATION CHECKS
Ensure battery is disconnected.
INSTALLATION
STEP 1
Remove the x8 push rivets which hold in place the x3 plastic covers.
STEP 2
Remove the x9 T25 torx screws from the top of the bumper.
STEP 3
Undo the x6 Torx 25 screws inside the front wheel arch.
Peel back the liner to access the x2 8mm bolts at the top of the bumper.
Repeat for both sides.
STEP 4
Undo the x2 8mm bolts at the top of the bumper.
Repeat for both sides.
STEP 5
Locate and remove the x8 Silver Torx 25 screws from under the front bumper.
STEP 6
Gently pull the edges of the bumper down to release the bumper sides.
Repeat for both sides.
STEP 7
Disconnect the headlight washer hoses, have a bucket ready to drain any fluid.
STEP 8
The bumper can now be removed and placed on a protective surface.
STEP 9
Measure out 650mm from the end of the lower aluminum bar 650mm across and 25mm
from the bottom up.
Use a 6mm drill bit to drill through the bar.
Repeat both sides.
STEP 10
Mount both the Linear side brackets to each other as shown.
Then mount the Linear side brackets to the Linear-18 as shown.
STEP 11
Bolt the lamp to the impact bar as shown.
STEP 12
Ensure the Linear-18 is working correctly before re-assembling the vehicle.
(Wiring Instructions on the next page)
WIRING INFORMATION
LAZER WIRING KIT
Mount the relay and connect the live and earth connections.
Tidy-up all wiring using cable ties.
WIRING WITH SWITCH
Run the switch cable through the factory grommet.
Drill a 20mm hole and install the switch.
WIRING WITH SPLICE
The purple high beam trigger can be fed through the bulkhead grommet, located
under the inspection panel as shown.
Please test the wires for a 12V signal beforehand.
CAN INFORMATION – FOR 2019+ VEHICLES ONLY
All vehicles with factory LED headlights will require a Canbus Interface to give a 12V output when the high beam is activated on the vehicle. V90 models from 2016-2018 are not compatible as they run on LinBus, not CanBus. For 2016-2018 models, the lamp can be controlled via the included switch.
The CAN wiring is located at the CEM (Body Control Module), in the Black/Green wiring connector, behind the dash pocket at the lower driver’s side dash aera.
CAN HI – GREY / BROWN
CAN LO – YELLOW / PURPLE
WWW.LAZERLAMPS.COM
+44 (0)1992 677374
sales@lazerlamps.com
Lazer Lamps Ltd, Units 1&2 Harlow Mill Business Centre, Riverway, Harlow, Essex. CM20 2FD. United Kingdom
MADE IN THE UK
/LAZERLAMPS
/LAZERLAMPS
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>