POWER-POLE DNE One Pump Remote User Guide

July 3, 2024
POWER-POLE

POWER-POLE DNE One Pump Remote

Specifications

  • Product Name: One Pump Remote
  • Parts Included: One Pump Remote, One Pump Remote Cradle, #8 1/2  Screws (2), Adhesive Strip, Lanyard
  • Speed Settings: Slow, Medium, Fast
  • Battery Type: CR2032 3V lithium coin battery

Product Usage Instructions

Cradle Installation

  1. Locate a flat surface to mount the remote cradle.
  2. Mark the upper hole location with a fine point marker and drill a pilot hole using a 7/64 drill bit.
  3. Place the remote cradle in the desired location and install one of the screws through the top hole.
  4. Repeat steps for the lower hole and mounting screw.

Pairing & Programming

  1. Press and hold the PROGRAM button on the Hydraulic Pump Unit (HPU) for 3 seconds.
  2. Press the UP button on the controller for one second. When paired, the LED will indicate successful pairing.

Battery Replacement

  1. Insert a small flathead screwdriver into the bottom of the remote to pry it apart.
  2. Remove the old battery and replace it with a CR2032 3V lithium coin battery.
  3. Reassemble the remote ensuring proper seating of components before snapping the shells into place.

Standard Operation
Press and hold either the Up or Down Button to move the anchor. Release to stop movement.

Auto Mode
Double tap either the Up or Down Button to automatically run the anchors until stowed or deployed.

Speed Settings
Toggle between slow, medium, and fast speed settings by tapping the corresponding button on the remote. LED lights indicate the current speed setting.

REMOTE PARTS

LABEL DESCRIPTION QTY.
A One Pump Remote 1
B One Pump Remote Cradle 1
C #8 1/2” Screw 2
D Adhesive Strip 1
E Lanyard 1

CRADLE INSTALLATION

For full remote instructions, consult the One Pump Installation & Owner’s Guide

NOTE: The remote cradle B
may also be installed using the supplied adhesive strip D .

  1.  Locate a suitable area with a flat surface to mount the remote cradle B .
  2.  Mark the upper hole location with a fine point marker and drill a pilot hole using a 7/64” drill bit.
  3.  Place the remote cradle Bin in the desired location and install one of the screws C through the top hole in the remote cradle B.
  4. Repeat Steps 2-3 for the lower hole and mounting screw C .

CRADLE INSTALLATION

WARNING!
Before installing the self-tapping screws, inspect the area beneath the mounting surface to ensure that the screws will not cause any damage

PAIRING & PROGRAMMING

IMPORTANT!
New remotes must be paired to the HPU.

  1. Press and hold the PROGRAM button on the top of the HPU for 3 seconds (LED will turn GREEN/HPU will beep).
  2. Press the UP button on the controller for one second. When paired, the GREEN LED will turn off and then flash steadily. HPU will beep.

STOWING & DEPLOYING

STANDARD OPERATION
Press and hold either the Up or Down Button. The anchor will only continue to move as long as the button is pressed.

AUTO MODE
Double tap either the Up or Down Button. The anchors will automatically run until stowed or deployed.

NOTE:
Auto mode can be changed to a single tap via the Power-Pole App.

STOW & DEPLOY

  1. The remote has 3 speed settings: slow, medium, and fast.
  2. Tap to toggle anchor speed.
  3. The LED lights will indicate the speed setting.

POWER-POLE -DNE- One- Pump- Remote-fig-5

BATTERY REPLACEMENT

IMPORTANT
Ensure the switch and the surrounding area are as dry as possible to avoid any moisture intrusion before changing the battery in the controller

  1. Insert a small flathead screwdriver into the bottom of the remote to pry it apart.
  2. Remove the battery from the holder on the circuit board and replace it with a CR2032 3V lithium coin battery.
  3. Re-assemble the remote, ensuring that the membrane is seated properly in the front shell before installing the cover and that the front and rear shells fully snap into place.

COMPLIANCE STATEMENTS

FCC Part 15.19 Warning Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FCC Part 15.21 Warning Statement
NOTE:
THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IC RSS-GEN, Sec 7.1.3 Warning Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. The applicant is responsible for providing proper instructions to the user of the radio device, and any usage restrictions, including limits of exposure durations. The user manual shall provide installation and operation instructions, as well as any special usage conditions, to ensure compliance with SAR and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user manual.

Detailed instructions can be found at www.power-pole.com/manuals Need Help? Contact our Customer Service Team at 1 + 813.689.9932
9010 Palm River Road Tampa, Florida 33619  Phone 1+ 813-689-9932 | Fax 1+813-689-8883 www.power- pole.com

FAQ

Q: How do I pair a new remote to the HPU?
A: Press and hold the PROGRAM button on the HPU for 3 seconds, then press the UP button on the controller to complete pairing.

Q: What battery type is recommended for replacement?
A: Use a CR2032 3V lithium coin battery to replace the remote’s battery.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals