SEACHOICE 72104 Bluetooth In Dash Marine Gauge Stereo User Manual

June 9, 2024
SEACHOICE

The Quality Choice
USER MANUAL
QUICK INSTALLATION GUIDE
Model 72104 BLUETOOTH® IN-DASH MARINE GAUGE STEREO SEACHOICE PRODUCTS

72104 Bluetooth In Dash Marine Gauge Stereo

Thank you for purchasing this MGR350BSC Bluetooth Gauge Radio Please read through these instructions carefully so you will know how to  operate your model properly.
After you have finished reading the instructions, keep this document in a safe place for future reference.

**THIS PACKAGE CONTAINS

**

INFORMATION TO THE USER

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks is under license. Other trademarks and trade names are those of their respective owners.

FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. The Bluetooth antenna cannot be  removed (or replaced) by user. This equipment complies with FCC? IC radiation exposure limits set forth for an uncontrolled environment and  meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very  low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be  installed and operated keeping the radiator at least 20 cm or more away from persons body (excluding extremities: hands, wrists, feet and ankles).  Alteration or modifications carried out without appropriate authorization may invalidate the users right to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Relocate or reorient the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

WARNING
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

BEFORE YOU START

IMPORTANT SAFETY PRECAUTIONS
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

  • Do not tum up the volume so high that you can’t hear what’s around you.
  • Use caution or temporarily discontinue use in potentially hazardous situations.
  • Do not operate mobile video equipment while driving a motorized vehicle safe driving and safety consideration of others should always be your highest priority.
  • Set your volume control at a low setting, then slowly increase the sound until you can hear it comfortably without distortion, or ear discomfort.
  • In the event you should notice smoke, strange noises or odor from this product, or any other abnormal signs, immediately turn off the power  and consult your dealer or the nearest authorized SEACHOICE Service Center. Using this product in this condition may result in permanent damage to the system.

INSTALLATION PRECAUTIONS
Always consult with a professional installer

  • Do not attempt to Install or service this product by yourself.
    Installation or servicing of this product by persons without professional trailing and experience In electronic equipment and motorized vehicle accessories may be dangerous and could expose you to the risk of electric shock, Injury or other hazards

  • Refer any repairs to a qualified SEACHOICE Service Center.

  • The MGR350BSC should be wired directly to a vehicles battery

  • When wiring directly to the vehicles battery, be sure to disconnect the batteries negative terminal wire before starting any wiring procedures, if  extending the main power primary wire, it is suggested that an optional fuse and fuse holder (not included) with minimum rating of 20  Amperes be in-line with the positive battery terminal

  • The ground cable length should be as short as possible, If extending from you battery, be sure to use a proper gauge rating for the length of the run, use only high quallty copper primary type wire

  • The MGR350BSC has a IPX6 weather resistant design, It should not be submerged In or under water under any circumstances

  • Do not use abrasive cleaning materials on the lens or bezel

  • Use only the Installation parts provided with the MGR350BSC

To avoid potential shorts in the electrical  system, be sure to disconnect the (-)  battery cable before installation. Use this unit with a 12-Volt battery and negative grounding only. Failure to do so may result Jin a fire or malfunction.

CAUTION When replacing the fuse, be sure to only use a fuse of the rating specified on this product. To avoid short-circuiting, cover any  disconnected leads with insulating tape. It is specially important to insulate any unused wires, which if left uncovered may cause a short circuit.  When connecting other devices to this product, refer to the manual for the product to be connected. The black cable is ground, make sure to  connect the ground wire first.
Ensure that the ground cable is properly connected to metal parts of the vehicles body frame or direct to the battery if your vehicle does not have a grounded chassis frame. The ground cable of this units power amp and a second powered system must be connected to the frame separately with  different screws. If the screw for the ground wire loosens or falls out, it could result in fire or malfunction.

SUGGESTED MOUNTING METHODS

CAUTION!!
Using other mounting methods may void this warranty

  1. Make the mounting hole size as follows

  2. Install studs mounts into rear of chassis

  3. Adjust M4 nuts for the best mounting depth

  4. Slip the unit through the hole cutout and into U-bracket

  5. Firmly tighten remaining M4 nuts

  6. Secure and waterproof the wiring

TOOLS NEEDED:

  • Measuring Tape / Ruler
  • Wrench and/or Pliers
  • Hole Saw
  • Crimp Too!

WIRE DIAGRAM

CAUTION!!
Do not ground or short the speaker leads

TROUBLE SHOOTING GUIDE

TROUBLE CAUSE SOLUTION
Unit will not turn on The fuse Is blown Check / replace the fuse
Ignition not engaged Turn ignition to on position
No sound is heard Blown speaker Replace faulty speaker
Volume Is low / muted Press the volume level up
Device is paused or muted Check your devices playing / volume status
Cannot pair Bluetooth The Bluetooth function of the device is not enabled

Refer to the user manual of the device for how to enable the Bluetooth function
The MGR350BSC BT memory Is flip| Follow how to reconnect a device In section E
The audio quality is poor after connection with a Bluetooth enabled device| The Bluetooth reception is poor| Move the device closer to the audio system or remove any obstacle between the device and the systems antenna
Unit has become unresponsive| Power glitch or Interference| Disconnect power for 10 seconds to reset
Low battery power| Charge battery, rim the engine to recharge the battery
Reset the main system| Follow steps In section B

TECHNICAL SUPPORT
1-805-751-4853
https://www.seachoice.com/contact-ns

SPECIFICATIONS

FM TUNER FREQUENCY RANGE

  • USA 87.5~107.9MHz
  • Europe 87.5~108MHz
  • Asia 87.5~108MHz
  • Australia 87.5~108MHz
  • Usable Sensitivity: 12dB (S/N=30dB)
  • Bands: 2 °

AM TUNER FREQUENCY RANGE

  • USA 30~1710KHz
  • Europe 522~1620KHz
  • Asia 22~1620KHz
  • Australia 522~1620KHz
  • Usable Sensitivity: 40dB (S/IN=20dB)
  • Bands: 1 °

WEATHER BAND SELECTION

  • CH.1 162.400MHz
  • CH.2 162.425MHz
  • CH.3 162.450MHz
  • CH.4 162.475MHz
  • CH.5 162.500MHz
  • CH.6 162.525MHz
  • CH.7 162.550MHz
  • Bands: 1 .

BLUETOOTH

  • BT: 3.0
  • BT Range: 33Ft / 10M (Class 2)
  • BT Profiles: A2DP / AVRCP 1.3

USB DRIVE MEDIA SUPPORTED

  • MP3
  • WMA
  • 65,006 Songs
  • 32GB / FAT 32
  • USB 2.0 High Speed
  • USB Output Voltage: 5VDC @ 1A

INTEGRATED AMPLIFIER

  • MOSFET
  • MAX Continuous Output: 240W (All channels driven)
  • PEAK Power Rating: 60W / channel
  • RMS Total Power Output: 80W
  • Channels: 4
  • Class: AB
  • Frequency Response: 20-20kHz
  • 4  stable

CHASSIS

  • Button Backlight Illumination: BLUE LED
  • FIR/S RCA Preamp Output: 2VRMS
  • RCA Input Impedance: 10k
  • LCD: TN Type / Active Matrix

GENERAL

  • Power Source: 14.4VDC
    (10.8V ~ 16V allowable)

  • Grounding System: Negative type

  • Maximum Current Consumption: 15A

  • 3-way protection circuitry (thermal, overload, and speaker short protection)

  • Unit Weight: 1.0S8ibs / 0.52kg

  • Storage Temperature: -22°F to 176°F / -30°C to 80°C

  • Operation Temperature: -4°F to 158°F / -20°C to 70°C

  • Replacement Fuse: 154A

(Replace with AGU Fuse Type Only)

Specifications subject to change without notice

GETTING STARTED

SOURCE MODES

| • Short press to mute or restore volume.
• Turn the unit on, Press and hold again to turn the unit off.
• Press to pause, Press again to resume playback.
---|---
| • Tuner/Weather Band Mode: Press to enter into the Manual Seek made, press and hold to enter into the Auto Seek mode.
• Media Playback Made: Press to Track Up/Down, press and hold for Fast Forward/Rewind.
SRC| Press to scroll and select available Source.
PRESET
Fn| Press to scroll and select Presets 1 — 6
Press and hold to enter into the Tuner Function modes:
A.STORE / M-STORE / LOCAL / AREA / RDS / AF / TA / PTY
| Press to decrease the volume, press to ;increase the valuate.

BAND
| • Tuner/Weather Band Mode To change different Band. Press at hold to
access into Auto Stone mode, the strongest stations of the selected band
will be saved in preset charnel autocratically. FM1, FM2,AM1, WB1 4′
• Made Playback Mode: Press to access into search Folder/File music made.
• Returns to the previous item
DISP ENTER| • Tuner Made: Press to view RDS receiver information.
• Media Playback: Press to view ID3 information.
AUDIO MENU| • Press to access into the Ada Menu mode for adjustments: EQ 1 XBASS I BASS / MIDDLE I TREBLE I BALANCE I FADER I REAROUT / SUBW / SUBW LPFISUBW LEVEL
• Press and hold to access into the System Menu:
BT RECONNECT / BEEP ON/OFF / ABOUT / RESET

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, Including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO SYSTEMS Inc.

TUNER SETUP

PRESET RECALL

MORE SETTINGS

1. Long Press for FUNCTION options| 2. Navigate Main System Tree| 3. Press ENTER to select option| 4. To select through
FUNCTION options
---|---|---|---
Media Playback Mode| Selectable settings
---|---
Repeat| • ALL: to repeat all tracks on the storage media
• Song: the current track will be repeated
• Folder repeats all tracks in the currant folder
Random On/Off|  This function allows you to play tracks/songs from the current album, songs or artists in a random order.
Tura Muds| Selectable settings
Auto Store| Press to access into A•STORE mode, the strongest stations of the selected band will be saved in FM 1 or FM 2, AM 1 BAND presets automatically
Manual Store| When a desired radio station is set, press M•STORE to save it in the memory, you can store a total of 12 FM or 6 AM.
Local On/Off| • ON: only stations with strong signal can be broadcast. The Local indicator will light up
• OFF: Stations of both strong and weak signals can be broadcast.
Area| Select suitable country area for this unit USA / EUROPE / ASIA / AUST
REPS On/Off| Turn On or Off the ADS function.
AF On/off| ON: The Irk will search for another station with stronger signal, but with the same program identification as the current station automatically.
OFF: Turn off AF function
TA On/off| ON: When there is traffic announcement, unit will automatically switch to the tuner mode (regardless of the current made) and bins to broadcast the announcement on traffic conditions. When the traffic announcement is oar, it may automatically return to the previous mode.
OFF: Traffic announcement does not cut in.
PTY ↵| Once inside the PTY mode, press to get into program type item, and rotate encoder volume knob to selected category.
• Available Program Type:
POP M; ROCK M; EASY M; LIGHT M; CLASSICS; OTHER M; JAZZ M; COUNTRY; NATION M; OLDIES M; FOLK M; A-TEST; ALARM; NEWS; AFFAIRS; INFO; SPORT; EDUCATE; DRAMA; CULTURE; SCIENCE; VARIED; WEATHER; FINANCE; CHILDREN; SOCIAL; RELIGION; PHONE IN; TRAVEL; LEISURE; DOCUMENT

AUDIO and SYSTEM SETUP

Tips: To avoid battery exhaustion be sure to run the vehicles engine while using this product.
Using this product without running the engine can drain the battery.

1. Long Press for FUNCTION options| 2. Navigate Main System Tree| 3. Press ENTER to select option| 4. To select through
FUNCTION options
---|---|---|---
Item| Selectable settings
---|---
BT ↵| This feature allows to Reconnect or Disconnect to the
paired mobile phone or Bluetooth device manually.
BEEP ↵| Turn On or Off beep sound.
RESET ↵| To restore the factory default settings.
ABOUT ↵| To view the device hardwired and software versions.

RADIO OPERATION

| 1) Press the SRC button to select RADIO
2) Press MUTE, press again to UNMUTE
3) To advance stations press
4) To skip previous stations press
5) Press the button to display RADIO information
6) Press the PRESET button to recall PRESETS 1 ~ 6
---|---

BLUETOOTH OPERATION

PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION

  1. Power on the MGR350BSC by pressing and holding down the Power button for 1 second, the Bluetooth ICON will start to flash signaling that the MGR350BSC Is now ready for Bluetooth pairing.
    NOTE: You have 2 minutes before you must restart this procedure over again.

  2. Now that the MGR350BSC Is In pairing mode:
    ANDROID users:
    a. Go Into the Settings Menu of your ANDROID device
    b. Enter the Bluetooth Menu and press SCAN
    c. “SEACHOICE 72104” will now be displayed under AVAILABLE DEVICES
    d. If prompted, enter passcode: “0000”
    IOS users:
    a. Go Into the Settings Menu of your IOS device
    b. Enter the Bluetooth Menu
    c. “SEACHOICE 72104” will now be displayed
    d. If prompted, enter passcode: “0000”

  3. If the MGR350BSC Is not seen, repeat the above steps to refresh the “Device List”

  4. When the BT connection Is successful you will see BT CONNECTED message on the MGR350B LCD display, you are now ready to stream music from your device to the MGR350BSC

RECONNECTION

  1. Power on the MGR350BSC and your last palred device Bluetooth

  2. The unit will now automatically be reconnected

  3. If your device was previously paired with the MGR350BSC, but It wasn’t the last palred device:
    a. Ensure no other devices are currently palred
    b. Press and hold MENU button to manually connect / reconnect to the MGR350BSC

  4. If the device Is out of range from the MGR350BSC, It will disconnect automatically:

  5. The MGR350B will reconnect to the device once In range, a confirmation message will be displayed on the LCD

BLUETOOTH STREAMING MUSIC

  1. Press the SRC button to select BT AUDIO
  2. Press start PLAY, press again to PAUSE
  3. To skip songs or advance tracks press , press and hold to FAST FORWARD
  4. To select the previous track press the button , press and hold to FAST REWIND
  5. Press the button to display song ID3 information

USB OPERATION

  1. Press the SRC button to select USB
  2. Press to start PLAY, press again to PAUSE
  3. To skip songs or advance tracks press , press and hold to FAST FORWARD
  4. To select the previous track press ; press and hold to FAST REWIND Loy
  5. Press the button to display song ID3 information

AUX-INPUT

  1. Press the SRC button to select AUX IN
  2. Press to MUTE, press again to UNMUTE

Tips: Ensure to adjust the level of your devices master volume to 75%

The Quality Choice

iPod® and iPhone® are trademarks of Apple, Inc. registered in the U.S. and other countries. Sea choice Products is not affiliated with Apple, Inc.

SEACHOICE PRODUCTS
Pompano Beach, FL U.S.A.
Made in China 0921

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals