SIEMENS ZIC-2C 2 Channel Audio Enhancement Card Instruction Manual
- June 9, 2024
- SIEMENS
Table of Contents
SIEMENS ZIC-2C 2 Channel Audio Enhancement Card
INTRODUCTION
The Model ZIC-2C from Siemens Industry, Inc., adds support for 2 channel audio to the ZIC-8B card. The ZIC-2C replaces the signal routing board that is installed on the ZIC-8B in the factory. The ZIC-2C mounts in the same location as the signal routing card and utilizes the same mounting hardware. Three 8 pin headers and one 20 pin header are also reused with the ZIC-2C.
Figure 1
ZIC-2C Two Channel Audio Enhancement Card.
INSTALLATION
Remove all system power before installation, first battery then AC. (To power up, connect the AC first, then the battery.).
- If the ZIC-8B is installed in the FireFinder XLS/Desigo Fire Safety Modular/Cerberus PRO Modular card cage (CC-5/CC-remove it now. If you are using a new ZIC-8B remove it from it’s carton.
- Remove the signal routing card from the ZIC-8B by removing the screws in the two mounting standoffs and gently pulling the signal routing card out of the connectors on the ZIC-8B. Save the screws. The two mounting stand-offs should remain attached to the ZIC-8B.
- Make sure that the three 8 pin headers and one 20 pin header between the ZIC-8B and the signal routing card remain installed in J4, J5, J10 and J11 of the ZIC-8B. If these headers stayed with the signal routing card remove them and re-install them into the ZIC-8B. Check that each header is completely seated in the receptacles on the ZIC-8B. (Refer to Figure 2.)
- Discard the signal routing card.
- Being careful to align all of the headers and the mounting standoffs, gently press the ZIC-2C down until the headers and standoffs fully mate. Check that all of pins of the headers are inserted into the sockets on the ZIC-2C and the ZIC-8B. Secure the ZIC-2C by reusing the two screws from Step 2.
- Install the ZIC-8B into the card cage ( CC-5/CC-2 ).
Siemens Industry
WIRING
Refer to the ZIC-8B installation instructions P/N 315-048670 for wiring diagrams for two channel audio applications.
ELECTRICAL RATINGS
Figure 2
The ZIC-8B After Removing The Signal Routing Card
Figure 3
Installing The ZIC-2C on the ZIC-8B.
__
24V Back Plane Current
| 17mA Per active output (ZIC-8B S1 in “BP POWER” position) 0mA
(ZIC-8B S1 in “EXT POWER” position)
---|---
__
Screw Terminal 24V Current
| 17mA Per active output (ZIC-8B S1 in “EXT POWER” position) 0mA
(ZIC-8B S1 in “BP POWER” position)
6.2V Back Plane Current| 0mA
24V Standby Current| 0mA
Cyber security disclaimer
Siemens products and solutions provide security functions to ensure the secure
operation of building comfort, fire safety, security management and physical
security systems. The security functions on these products and solutions are
important components of a comprehensive security concept.
It is, however, necessary to implement and maintain a comprehensive, state-of-
the-art security concept that is customized to individual security needs. Such
a security concept may result in additional site-specific preventive action to
ensure that the building comfort, fire safety, security management or physical
security system for your site are operated in a secure manner. These measures
may include, but are not limited to, separating networks, physically
protecting system components, user awareness programs, defense in depth, etc.
For additional information on building technology security and our offerings,
contact your Siemens sales or project department. We strongly recommend
customers to follow our security advisories, which provide information on the
latest security threats, patches and other mitigation measures.
http://www.siemens.com/cert/en/cert-security-
advisories.htm
Siemens Industry, Inc. Building Technologies Division Florham Park, NJ
Siemens Canada, Ltd.
1577 North Service Road East Oakville, Ontario
L6H 0H6 Canada
Document ID A6V10239144
P/N 315-048671-3
References
- Fire Alarm Resources | Download fire alarm documents
- CERT Services - Services - Siemens Global Website