ergtron HX Desk Monitor Arm with Heavy Duty Tilt User Guide
- June 9, 2024
- ergtron
Table of Contents
ergotron HX Desk Monitor Arm with Heavy Duty Tilt
WHAT IN BOX
Tools Needed
DIMENSION
NOTE: Determine if arm will typically collapse to the left or right
before installation.
INSTALLATION
OPTIONAL: Grommet Mount Installation 
NOTE: The short screw must be reinstalled in the front hole of the grommet
mount. 
Rotate- Portrait/Landscape
NOTE: Arm exstension should be at a 45° angle or less when attaching
monitor.
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Tilt- Forward and Backward
CAUTION: D0 NOT remove screw. Removing screw may cause damage to equipment.
+: Increase Lift Strength If the mounted weight is too heavy or this
product does not stay up when raised, then you’ll need to increase Lift
Strength:
-: Decrease Lift Strength If the mounted weight is too light or this
product does not stay down when lowered, then you’ll need todecrease Lift
Strength:
Lift- Up and down
Adjustment may take up to: 35 full 360° revolutions
+: Increase Lift Strength If the mounted weight is too heavy or this
product does not stay up when raised, then you’ll need to increase Lift
Strength:
-: Decrease Lift Strength If the mounted weight is too light or this
product does not stay down when lowered, then you’ll need to decrease Lift
Strength:
Monitor Pan- Left and Right
+: Increase Friction
If this product moves too easily, then you’l need to increase friction:
-: Decrease Friction
If this product is too difficult to move, then you’ll need to decrease
friction:
Safety
Warning: Because mounting surface materials can vary widely, it is
imperative that you make sure mounting surface is strong enough to handle
mounted
product and equipment.
Caution: Leave enough slack in cable to allow full range of motion.
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in
equipment damage or personal injury.
Remove monitors before loosening desk attachment.
WARNING! Stored Energy Hazard: The arm mechanism is under tension and
will move up rapidly, on its own, as s0on as attached equipment is removed.
For this reason, DO NOT remove equipment unless the arm has been moved to the
highest position! Failure to follow this instruction may result in serious
personal injury andlor equipment damage!
CAUTION: For Desk Clamp installations: Do Not rotate display past edge of desk
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUs INJURY OR
PROPERTY DAMAGE MAY OCCUR!
For the latest User Instalation Guide please visit:
www.ergotron.com
For Waranty visit
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
Learn more about ergonomiC computer use at: www.ergotron.com/ergonomics
www.ergotron.com| USA: 1-800-888-8458| Europe: +31 (0)33-45 45 600| China: 400-120-3051| Japan: japansupport@ergotron.com
2021 Ergotron, Inc. All rights reserved.
While Ergotron, Inc. makes every effort to provide accurate and complete
information on the installation and use of its products, it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or tor incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Ihc. reserves the right to make changes in the product design and/or
product documentation without notification to its users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording or otherwise
without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan,
Minnesota, 55121, USA
Patents Pending and Patented U.S. & Foreign. trgotron is a registered
trademark of Ergotron, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>