Shinko HR-706 Channel 6 Point Temperature and Electrical Recorder User Manual

HR-706 Channel 6 Point Temperature and Electrical Recorder
User Manual
HR-706 Operation Flow Chart 

HR-706 Channel 6 Point Temperature and Electrical Recorder

WARNING
When calibrating data, connect the equipment according to Section 9.5 of the instruction manual. Data calibration must be performed correctly.
Operators possessing knowledge of electricity and control related matters should perform the calibration after careful reading of Sections 7.2 and 9.5 of the instruction manual.
(Shinko Technos Co., Ltd. is not liable for damages incurred if calibration is performed other than prescribed in the instruction manual.)

**Normal Operation Mode : Recording, Changing the Display, Engineering

List Printing, Manual Printing, List Printing**

**Setup Mode : Setting the Range (Current/Voltage, Thermocouple,

Resistance temperature detector)**

Setup Mode : Setting the Range (scaling) Setup Mode : Setting the Range (Square Root) Setup Mode : Setting the Range (Decade) Setup Mode : Setting the Range (Difference, Sum, Average) Setup Mode : Setting the Range (Skip) Setup Mode : Setting the Alarm
Setup Mode : Setting the Unit Setup Mode : Setting the Chart Feed Speed, Setting the Date and Time Setup Mode : Copying the Setting Data
Setup Mode : Setting Other Functions(Printing Cycle, Zone Recording)

Setup Mode : Setting Other Functions(Partial Compression/Expansion)

Setup Mode : Setting Other Functions(Digital Printing)

Setup Mode : Setting Other Functions(Tag)

Setup Mode : Setting Other Functions(Comments)

Engineering Mode : Alarm Hysteresis, Burnout ON/OFF

Engineering Mode : Channel Offset Engineering Mode : Reference Junction Compensation

Engineering Mode : Changing the Printing Color

Engineering Mode : Recording RUN/STOP Trigger Setting, Channel/Tag Printing Selection, Alarm printing ON/OFF Engineering Mode : Logging printing ON/OFF, Scale printing ON/OFF, Synchronous/Asynchron ous
Engineering Mode : Setting the Communication Function, Initializing the Setup Data

Engineering Mode : DI Functions

Engineering Mode : Temperature Unit Selection, Point Calibration
Engineering Mode : Data Calibration(Voltage)

WARNING
When calibrating data, connect the equipment according to Section 9.5 of the instruction manual.
Data calibration must be performed correctly.
Operators possessing knowledge of electricity and control related matters should perform the calibration after careful reading of Sections 7.2 and 9.5 of the instruction manual.
(Shinko Technos Co., Ltd. is not liable for damages incurred if calibration is performed other than prescribed in the instruction manual.)

Engineering Mode : Data Calibration (Resistance temperature detector)

**WARNING**
When calibrating data, connect the equipment according to Section 9.5 of the instruction manual.
Data calibration must be performed correctly.
Operators possessing knowledge of electricity and control related matters should perform the calibration after careful reading of Sections 7.2 and 9.5 of the instruction manual.
(Shinko Technos Co., Ltd. is not liable for damages incurred if calibration is performed other than prescribed in the instruction manual.)

Engineering Mode : Data Calibration (Terminal Temperature)

WARNING
When calibrating data, connect the equipment according to Section 9.5 of the instruction manual.
Data calibration must be performed correctly.
Operators possessing knowledge of electricity and control related matters should perform the calibration after careful reading of Sections 7.2 and 9.5 of the instruction manual.
(Shinko Technos Co., Ltd. is not liable for damages incurred if calibration is performed other than prescribed in the instruction manual.)

Default value

Setup mode

| Range (all channels)| —10-10mV
0∼100.0| | |
| |

| Alarm
(all channels)| All levels alarm OFF, Relay OFF| | |
| |

| Engineering unit (all channels)| | | |
| |

| Chart feed speed| (1)20mm/h| | |

| Time| 2000/01/01 00:00| The present time has been set. (Japan standard time) GMT + 09:00

| Setting other recordings| |

| Dot point interval| 10(sec)|

| Zone setting (all channels)| 0-100(%)| | |
| |

| Partial compression/expansion (all channels)| OFF| | |
| |

| Tag printing character (all channels)| Blank up to the 7’h character| | |
| |

| Comment printing word (1 to 3)| Blank up to the 16th  character| | |

Engineering mode

| Alarm hysteresis| ON(0.5%)|

| Burnout (all channels)| OFF| | |
| |

| Channel offset (all channels)| 0.0| | |
| |

| RJC (all channels)| Internal compensation INT|

| Dot printing color (Ch1 to Ch6)| Purple(1), Red(2), Green(3), Blue(4), Brown(5), Black(6)|

| REC (recording)| | Use the “AEC” key

| RUN/STOP trigger| INT

| ChanneVTag printing| Ch

| Alarm printing| OFF

| Logging printing| ON

| Logging printing reference time| 0:00

| Logging printing interval| 6H

| Logging scale printing| OFF

| DI function (Chi to Ch3)| OFF|

SHINKO TECHNOS CO., LTD.
OVERSEAS DIVISION
Head Office: 2-5-1, Senbahigashi, Minoo, Osaka, Japan
URL: http://www.shinko-technos.co.jp/e/
E-mail: overseas@shinko-technos.co.jp
Tel : +81-72-727-6100
Fax: +81-72-727-7006

References

• テクノス株式会社｜金庫・貸金庫設備の販売・施工・保守
• Shinko Technos for temperature and humidity control

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>