Panasonic ET-LAV400 Replacement Lamp Unit Instruction Manual

: June 9, 2024
: Panasonic

Table of Contents

ET-LAV400 Replacement Lamp Unit
How to replace the lamp unit
Replacement procedure
Documents / Resources

Operating Instructions
Replacement lamp unit
Model No. ET-LAV400

ET-LAV400 Replacement Lamp Unit

Thank you for purchasing this Panasonic product.

Please read these operating instructions and the projector operating instructions carefully, and then use this product correctly.
Before using this product, be sure to read [Read this first!] (xPage 2).
Please save this manual for future use.

Read this first!
Always follow these precautions
WARNING

Do not remove any screws other than those indicated when replacing the lamp unit.
If this is not observed, electric shocks, burns or other injuries may occur.
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will result.
The lamp can easily explode if struck against hard objects or dropped.
Before replacing the lamp, be sure to disconnect the power plug from the wall outlet. Electric shocks or explosions can result if this is not done.
When replacing the lamp, turn the power off and allow it to cool for at least 1 hour before handling it otherwise it can cause burns.
CAUTION
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room immediately.
Do not touch or bring your face close to the broken pieces.
Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces will cause injury.
If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical advice immediately.
Ask your dealer about replacing the lamp unit and check the inside of the projector.

Notice (for USA only)
Hg-LAMP CONTAINS MERCURY, Manage in Accord with Disposal Laws.
See: www.lamprecycle.org or 1-888-411-1996.
This lamp is used in projectors.
It is not intended to be used for indoor lighting of ordinary homes.
2009 / 125 / EC
Illustrations in this manual

Illustrations contained in this manual that show the projector may differ from the actual objects they depict.

** Manufactured by: Panasonic Connect Co., Ltd. 4-1-62 Minoshima, Hakata- ku, Fukuoka 812-8531, Japan
Importer: Panasonic Connect Europe GmbH
Authorized Representative in EU: Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
Importer for UK:**
Panasonic Connect UK, a branch of Panasonic Connect Europe GmbH,
Maxis 2, Western Road, Bracknell, Berkshire, RG12 1R

How to replace the lamp unit

Attention

The light source lamp is a glass component. If it is hit on a hard object or dropped, breakage may occur.
Be careful when handling a light source lamp.
Grip the handle when you remove the lamp unit. Some parts of the lamp unit are sharpened and may cause injury.
Do not disassemble or modify the lamp unit.
When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately.
When the projector is mounted on a ceiling, do not work with your face close to the projector.
Attach the lamp unit and the lamp cover securely.
Panasonic Connect Co., Ltd. takes no responsibility for any damage or malfunction of the product resulting from use of lamp units which are not manufactured by Panasonic Connect Co., Ltd. Use only specified lamp units.
Do not loosen other than designated screws.

Note

A Phillips screwdriver is necessary when carrying out replacement.
Hold the screwdriver firmly.

Replacement procedure

Switching off the projector and then remove the AC power plug from the wall outlet.
When switching off the projector, make sure to follow the procedures in “Switching Off the Projector” in the operating instructions of the projector.
Wait at least one hour and make sure the lamp unit and surroundings are cool.
Use a Phillips screwdriver to loosen the lamp cover fixing screw (one screw) until it turns freely and remove the lamp cover.
Remove the lamp cover by pulling it slowly toward the direction of the arrow.
Use a Phillips screwdriver to loosen the lamp unit fixing screws (three screws) until they turn freely.
Hold the used lamp unit by its handles, and pull it gently from the projector
Insert in the new lamp unit (Replacement Lamp Unit) while paying attention to the insertion position. Tighten the lamp unit fixing screws (three screws) securely with a Phillips screwdriver.
If the lamp unit is not installed properly, remove it and then push it in slowly. Pushing it in quickly or forcibly may break the connector.
Attach the lamp cover. Tighten the lamp cover fixing screw (one screw) se- curely with a Phillips screwdriver.
Perform step 2) in reverse direction to attach the lamp cover.
Note
When you replace the lamp unit with new one, the projector resets the runtime of the lamp unit automatically.

Attention

The lamp contains mercury. Contact the local government office or distributor for the correct disposal of the old lamp unit.
After unpacking the lamp unit, discard the packaging material properly.

MEMO
Disposal of Old Equipment
Only for European Union and countries with recycling systems
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local authority.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
Product information (for Turkey only)
AEEE Yönetmeliğine Uygundur.

Panasonic Connect Co., Ltd.
© Panasonic Connect Co., Ltd. 2022
Web Site :https://panasonic.net/cns/projector/
TI0714ZF3062 -PT
Printed in China

Documents / Resources

| Panasonic ET-LAV400 Replacement Lamp Unit [pdf] Instruction Manual
ET-LAV400, Replacement Lamp Unit, ET-LAV400 Replacement Lamp Unit, Lamp Unit
---|---