SCS Sentinel Codeaccess A Coding Keyboard Instruction Manual

: June 9, 2024
: SCS sentinel

Table of Contents

SCS Sentinel Codeaccess A Coding Keyboard
SAFETY INSTRUCTIONS
DESCRIPTION
WIRING/ INSTALLING
- Wiring diagram
TO RESET TO FACTORY DEFAULT
INDICATIONS
USING
- Fast programming
Detailed Programming Guide
TECHNICAL FEATURES
WARRANTY
Documents / Resources

SCS Sentinel Codeaccess A Coding Keyboard

SCS-Sentinel-Codeaccess-A-Coding-Keyboard-PRODUCT

SAFETY INSTRUCTIONS

This manual is an integral part of your product.
These instructions are provided for your safety. Read this manual carefully before installing and keep it in a safe place for future reference. Select a suitable location. Make sure you can easily insert screws and wallplugs into the wall. Do not connect your electrical appliance until your equipment is totally installed and controlled. The installation, electric connections, and settings must be made using best practices by a specialized and qualified person. The power supply must be installed in a dry place.
Check the product is only used for its intended purpose.

DESCRIPTION

Content / Dimensions

WIRING/ INSTALLING

installing

For a better seal, put silicone on the top and the 2 sides of the keyboard

Wiring diagram

To gate automation

To strike/electric lock

TO RESET TO FACTORY DEFAULT

a. Disconnect power from the unit
b. Press and hold # key whilst powering the unit back up
c. On hearing two “Di” release # key, system is now back factory settings
Please note only installer data is restored, user data will not be affected.

INDICATIONS

Operation Status	Red Light	Green Light	Buzzer
Stand by	Blinking
Press keypad			DI
Operation successful		Bright	DI
Operation failed			DI DI DI
Enter into programming mode	Bright
In the programming mode	Bright	Bright	DI
Exit from the programming mode	Blinking		DI
Open the door		Bright	DI

USING

Fast programming

Programming a code

Door opening
Trigger the opening through user code

To trigger the opening with a badge, you only have to present the badge to the keypad.

Detailed Programming Guide

User Settings

To enter the programming mode| * Master code #

999999 is the default factory master code

---|---
To exit from the programming mode| *
Note that to undertake the following programming the master user must be logged in
Setting the working mode: Set valid card only users

Set valid card and PIN users

Set valid card or PIN users

| 3 0 # Entry is by card only

3 1 # Entry is by card and PIN together

3 2 # Entry is by either card or PIN (default)

To add a user in either card or PIN mode, i.e. in the 3 2 # mode. (Default setting)

To add a PIN user

| 1 User ID number # PIN #

The ID number is any number between 1 & 100. The PIN is any four digits between 0000 & 9999 with the exception of 1234 which is reserved. Users can be added continuously without exiting programming mode as follows: 1 User ID no 1

PIN # User ID no 2 # PIN #

To delete a PIN user| 2 User ID number # Users can be deleted conti- nuously without exiting programming mode
To change the PIN of a PIN user (This step must be done out of programming mode)| * ID number # Old PIN # New PIN # New PIN #
To add a card user (Method 1) This is the fastest way to enter cards, user ID number auto generation.| 1 Read card # Cards can be added continuously without exiting programming mode
To add a card user (Method 2) This is the alternative way to enter cards using user ID Allocation. In this method a user ID is allocated to a card. Only one user ID can be allocated to a single card.| 1 ID number # Read card # User can be added continuously without exiting programming mode
To delete a card user by card. Note users can be deleted continuously without exiting programming mode| 2 Read Card #
---|---
To delete a card user by user ID. This option can be used when a user has lost their card| 2 User ID #
To add a card and PIN user in card and PIN mode ( 3 1 # )
To Add a card and Pin user

(The PIN is any four digits between 0000 & 9999 with the exception of

1234 which is reserved.)

| Add the card as for a card user Press

to exit from the programming mode

Then allocate the card a PIN as follows:

Read card| 1234 #| PIN #| PIN #
To change a PIN in card and PIN mode (Method 1) Note that this is done outside programming mode so the user can undertake this themselves| Read Card| Old PIN # New PIN #
New PIN #
To change a PIN in card and PIN mode (Method 2) Note that this is done outside programming mode so the user can undertake this themselves| ID number # Old PIN # New PIN # New PIN #
To delete a Card and PIN user just delete the card| 2 User ID #
To add and delete a card user in card mode ( 3 0 # )
To Add and Delete a card user| The operating is the same as adding and deleting a card user in 3 2 #
TO DELETE ALL USERS
To delete all users. Note that this is 2 0000 # a dangerous option so use with care| 2 0000 #
TO UNLOCK THE DOOR
For a PIN| user Enter the PIN then press #
For a card User| Read card
For a card and PIN user| Read card then enter PIN #

Door settings

RELAY OUTPUT DELAY TIME

To set door relay strike time| Master code # 4 0~99 # 0-99 is

to set the door relay time 0-99 seconds

To disable door open detection. (Factory default)| 6 0 #
To enable door open detection| 6 1 #

Changing the master code

Changing the master code

| 0 New code # New code #

The master code consists of 6 to 8 digits

---|---

For security reasons we recommand changing the master code from default.

TECHNICAL FEATURES

Voltage 12V DC +/-10%
Badge reading distance 0-3 cm
Active current < 60mA
Stand-by current 25±5mA
Lock load output 3A max
Operating temperature -35°C ~ 60°C
Relay output delay time
Possible wiring connections: electric lock, gate automation, exit button
Backlight keys
100 users, supports badge, PIN, badge + PIN
Full programming from the keypad
Can be used as a stand-alone keypad
The keyboard can be used to remove the lost badge number, thoroughly eliminate the hidden safety trouble
Adjustable Door Output time, Alarm time, Door Open time
Fast operating speed
Lock output current short circuit protection
Indicator light and buzzer
Frequency: 125 kHz
Maximum transmitted power: 2,82 mW

WARRANTY

(2 Warranty 2 years

The invoice will be required as proof of purchase date. Please keep it during the warranty period. Carefully keep the barcode and the proof of purchase, that will be necessary to claim warranty.

WARNING

Maintain a minimum distance of 10 cm around the device for sufficient ventilation.
Keep matches, candles and flames away from the device.
Product functionality can be influenced by a strong electromagnetic interference.
This equipment is intended for private consumer use only.
The appliance should not be exposed to dripping or splashing water; no objects filled with liquids, such as vases, should be placed near the appliance.
Do not use in a tropical climate.
Connect all the parts before switching on the power.
Do not cause any impact on the elements as their electronics are fragile.
When installing the product, keep the packaging out of reach of children and animals. It is a source of potential danger.
This appliance is not a toy. It is not designed to be used by children.
Disconnect the appliance from the main power supply before service. Do not clean the product with solvent, abrasive or corrosive substances. Only use a soft cloth. Do not spray anything on the appliance.
Make sure that your appliance is properly maintained and regularly checked in order to detect any sign of wear. Do not use it if a repair or adjustment is needed. Always call on qualified personnel.
Don’t throw batteries or out of order products with the household waste (garbage). The dangerous substances that they are likely to include may harm health or the environment. Make your retailer take back these products or use the selective collect of garbage proposed by your city.
Toutes les infos sur :
www.scs-sentinel.com
110 rue Pierre-Gilles de Gennes 49300 Cholet – France