ENOVATES Single Wallbox Pedestal Instruction Manual

June 9, 2024
ENOVATES

ENOVATES Single Wallbox Pedestal

SAFETY PRECAUTIONS

Safety terminology

| Danger texts provide important information to avoid situations with a high chance to cause severe malfunction, damage, injuries or death.
---|---
| Warning texts provide important information to avoid situations with a significant chance to cause malfunction, damage, injuries or death.
| Caution texts provide important information to avoid situations that may cause some degree of malfunction, damage or injuries.

Precautions

| The installer must wear protective footwear while performing the installation.
---|---
| The installer is responsible for checking the installation area’s subsurface (underground) for the presence of cables, tubes, etc.
| The pedestal must be mounted on concrete, level with the ground, according to the regulations. Mounting on soft soil, or in any other way than is detailed, is not allowed.

REQUIRED TOOLS

Required Tools
Required Tools

#

|

Description

|

Amount

---|---|---

1

|

eNovates pedestal

|

x1

2

|

Spirit level

|

x1

3

|

Folding rule

|

x1

4

|

Screwdriver Torx T25

|

x1

5

|

Screwdriver PH2

|

x1

|

Only required when installing on soft soil:

|

6

|

Anchor

|

x1

7

|

Spade

|

x1

8

|

Concrete

|

75 kg

9

|

Bucket of water

|

10 l

10

|

Large mixing tub

|

x1

11

|

Mixer

|

x1

12

|

Hammer drill

|

x1

13

|

Drill 10 mm

|

x1

PEDESTAL INSTALLATION

The base of the pedestal can be fixed to an anchor that is buried in the ground.

Note: The pedestal has been designed to offer a standardized mounting height for the charger, when attached to a subsurface anchor and mounted from the ground up. Do not alter the pedestal’s height using additional connecting pieces or other modifications.

Carefully consider where the charging station will be created, and how the charger unit(s) will need to be oriented. The anchor will be set into the ground and the pedestal will be set on the anchor, aligned with the holes in the anchor pole. Keep this in mind when considering the desired final orientation of the charger unit(s).
Make sure that the power cord and ethernet cable are already available (two of each cable when a double pedestal is used) and that the cables will be able to reach up through the pedestal from below, at the position where the pedestal will be placed. For more details, refer to the main installation manual for your product.

Anchor attachment
  1. Dig a hole for the ground anchor, approximately 50 cm deep and 30 x 40 cm wide.
    Avoid digging much deeper than necessary, as this will cause the soil to become looser. In a few years’ time, the stability of the ground mount may degrade if the soil is too loose. ****| The pedestal must be mounted on concrete, level with the ground, according to the regulations. Mounting on soft soil, or in any other way than is detailed, is not allowed.
    ---|---

  2. Make sure the necessary underground cables lead into the created hole and stick out from it. The cables must be enveloped by a protective flexible sheath in the area where concrete will be poured. The cables must be able to reach up into the charger unit and to be connected to the charger unit when the anchor and pedestal are placed.

  3. Assemble the anchor
    Pedestal Installation

  4. Lead the cables through the anchor’s central axis until they stick out and place the anchor in the hole. Make sure the anchor is level and that the pedestal can be attached to the pole slot at surface level.

  5. Pour concrete to fix the anchor in place. Let the concrete harden.
    If necessary, add a layer of filler soil on top of the hardened concrete and stomp the soil down until it is level.

  6. Feed the cables from the anchor through the inside of the pedestal and out of the opening at the bottom of the pedestal bracket. Then place the pedestal onto the anchor’s pole slot.
    Pedestal Installation

  7. Make sure the pedestal bracket is facing the way you want it to. When properly positioned, fix the pedestal to the anchor slot with 3 screws.

PEDESTAL MOUNTING

The mounting procedure consists of a few steps:

  1. Secure the cable block to the pedestal.
  2. Slide the charger onto the pedestal.
  3. Secure the charger to the pedestal.
  4. Connect the cables.
  5. Attach and secure the cover.
  6. Attach and secure the socket lid.
  7. If necessary, attach a C sticker.
Secure the cable block to the pedestal.
  1. Make sure the bridge component is removed from the cable block included in the box of the charger. Slot the cable block onto the bottom of the pedestal bracket. Orient the cable block so that the cables can pass from the circular holes in the bottom corner of the pedestal bracket through the cable block and into the charger unit when the charger unit is attached.
    Pedestal Mounting

  2. Use the provided 2 M5x16 screws (Torque 1.2Nm) to secure the cable block onto the bottom of the pedestal bracket.

The following steps in the mounting procedure

Please refer to the step “Slide the charger onto the wall bracket” in the Wall Mounting chapter of the product manual to perform the following steps in the mounting procedure. The same principles that apply to the wall bracket in the product manual from this step forward, can be applied to the pedestal bracket.

Customer Support

Manufacturer
eNovates N.V.
Brandstraat 13
9160 Lokeren
Belgium
KBO 0833.289.547

To access the Single Wallbox Installation Manual please scan the QR code or use the link
https://www.enovates.com/manual-installation-manual/

To access the Pedestal Installation Manual please scan the QR code or use the link
https://www.enovates.com/manual-pedestal-installation/

To access the Single Wallbox User Manual  please scan the QR code or use the link
https://www.enovates.com/manual-user-manua

Documents / Resources

| ENOVATES Single Wallbox Pedestal [pdf] Instruction Manual
Single Wallbox Pedestal, Wallbox Pedestal, Pedestal, Single Wallbox, Wallbox
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals