ISOtunes IT-75 Ultracomm Aware True Wireless Noise Isolating Earbuds User Manual
- June 9, 2024
- ISOtunes
Table of Contents
ISOtunes IT-75 Ultracomm Aware True Wireless Noise Isolating Earbuds
INSTALLATION INSTRUCTION
ANSI S3.19-1974 Table (NRR Table)
EN 352-2:2020 Table (SNR Table)
Important
- Please read, understand, and follow all safety information.
Models
- IT-75: ISOtunes ULTRACOMM Aware
- IT-76: ISOtunes ULTRACOMM Aware EN 352
- The full manual can be found at ISOtunes.com/manuals.
Introduction
- Thank you for purchasing ISOtunes® ULTRACOMM
- Aware True Wireless Noise-Isolating Earbuds.
- These earbuds are specifically designed for use in noisy environments – allowing you to block out much of the surrounding noise so you can listen to your music or talk on the phone with less interruption.
Fitting
- Carefully roll the foam eartip on the stem/sound port (Fig. 1).
- Insert the eartip into your ear as deeply as comfortable (Fig. 2).
- Slightly rotate earbud until it is secure in the bowl of your ear (Fig. 3).
- Make the earbud rest tightly next to your inner ear edge.
- Gently wrap the comfort-fit ear hooks around the top and back of your ears.
Power On/Off
Method 1
- Power ON: Open the charging case
- Power OFF: Place earbuds into the charging case and close the lid
Method 2
- Power ON: In OFF mode, press and hold the multi-function button (MFB) for 3 seconds
- Power OFF: In ON mode, press and hold the multi-function button (MFB) for 3 seconds
Bluetooth® Pairing
- After powering on, the earbuds will automatically enter Bluetooth Pairing Mode. Look for quick red and blue flashes from the earbud as a confirmation. Open the Bluetooth® settings on your device. Search for “ISOtunes ULTRACOMM Aware.” Pair and connect. You will hear “Bluetooth Connected” once connected
Phone Calls
- Each earbud contains a built-in microphone for making phone calls. For enhanced voice clarity, consider using the included configurable boom microphone.
- Open the microphone port cover on either earbud by pulling up the exposed tab. Then, align the arrow on the earbud with the arrow on the boom microphone. Insert the audio jack into the earbud, pressing firmly to ensure that it’s fully seated.
Remove the boom microphone and store in the lid of the charging case when not in use.
Charging
There are three batteries to charge:
- Charging Case Battery
- Left Earbud Battery
- Right Earbud Battery
Charging the Case
- Insert USB-C charging cable to charge the case. The charging case battery indicator light will start flashing to indicate charge level.
Charging the Earbuds
- Place earbuds into the charging case. The earbuds’ indicator light should be solid red, indicating that the earbuds are charging.
- Only charge your ISOtunes ULTRACOMM Aware with a maximum 5 Volt charger. Using a charger higher than 5 Volts could be dangerous and may damage your ISOtunes product. Be especially careful with “quick charge” or “turbo charge” chargers, which often supply 9, 12, or 15 Volts.
Noise Attenuation
- This product has been tested to the European Safety Standard EN352-2:2020 and the ANSI S3.19-1974 standard for a hearing protector with a Single Number Rating (SNR) of 32 dB and a Noise Reduction Rating (NRR) of 24 dB. Full testing details are available on page 2 of this booklet.
ANSI S3.19-1974
- The level of noise entering a person’s ear, when ISOtunes® ULTRACOMM Aware earbuds are worn as directed, is closely approximated by the difference between the A-weighted environmental noise level and the Noise Reduction Rating (NRR). Improper fit of this device will reduce its effectiveness in attenuating noise. Consult the enclosed instructions for proper fitting.
- A1: Frequency (Hz)
- A2: Mean Attenuation (dB)
- A3: Standard Deviation (dB)
Example:
- The surrounding noise level measured at the ear is 100 dB.
- The NRR of ISOtunes® ULTRACOMM Aware is 24 dB.
- The noise level entering the ear is approximately equal to 76 dB. Please note that the NRR is based on the attenuation of continuous noise and may not be an accurate indicator of the protection attainable against impulsive noise, such as gunfire.
EN 352
- B1: Frequency (Hz)
- B2: Mean Attenuation (dB)
- B3 : Standard Deviation (dB)
- B4 : Assumed Protection Value (APV) (dB)
- H = Hearing protection estimation for high frequency sounds (f ≥ 2000Hz)
- M = Hearing protection estimation for medium frequency sounds (500Hz < f < 2000Hz)
- L = Hearing protection estimation for low frequency sounds (f ≤ 500Hz)
SafeMax™ Technology
- ISOtunes® ULTRACOMM Aware incorporates
- SafeMax™ Technology; therefore, its volume output is limited to 85 decibels (IT-75), or 79 decibels (IT-76). ISOtunes® devices with SafeMax™
- Technology are ANSI tested and OSHA compliant.
Aware™ Technology
- When utilizing the boom mic and listening to music, Aware Technology will remain useable and active, based on the user’s adjustment.
- Once a call is taken or the earbuds are connected to a communication device, Aware
- Technology will turn off. As this device is focused on use in loud environments, this feature is meant to allow the user to hear the digital communication via earbud more clearly.
ULTRACOMM Aware has 4 levels of Aware:
- High
- Medium
- Low
- Off
- The levels are changed by tapping the left earbud on the top of the center panel. Increase the volume by tapping once, or decrease the volume by tapping twice. A single beep means that the level has successfully been raised/ lowered. A double beep means that the highest or lowest Aware level has been reached.
Cleaning and Maintenance
- Clean your ISOtunes ULTRACOMM Aware by gently wiping them with a clean, damp cloth with mild soap.
- Do not immerse the earbuds in water.
- Do not use abrasive cleaning solvents to clean the earbuds.
- If the earbuds get wet from sweat or rain, please discontinue use and allow them to dry.
WARNINGS
- ISOtunes® ULTRACOMM Aware does an excellent job of blocking outside noise. As such, ISOtunes®
- ULTRACOMM Aware should NOT be used in environments where users need to be fully aware of their surroundings for personal safety reasons. For example, do NOT use them while driving a car or riding a motorcycle. Similarly, do NOT use them when riding a bicycle outside.
- The user is solely responsible for ensuring that ISOtunes® ULTRACOMM Aware is used ONLY in safe environments.
Additional Notes
- ISOtunes® ULTRACOMM Aware is compliant with Bluetooth® V5.2. We do not guarantee compatibility of all functions on every Bluetooth®- enabled device. Please check your device’s user manual for compatibility and functionality.
- For additional information or questions about ISOtunes® products or spares and accessories, please contact our support team.
FCC
- Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the users’ authority to operate the equipment.
- Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
- This equipment complies with FCC‘s RF radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
IC
-
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
-
Development Canada’s licenceexempt
-
RSS(s). Operation is subject to the following two conditions:
-
This device may not cause interference.
-
This device must accept any interference, including interference that may cause undesired operation of the device.
-
Hereby, Haven Technologies declares that the
-
IT-76 complies with Regulation (EN)2016/425 and
-
EN 352-2:2020, EN 352-7:2020, EN 352-9:2020,
-
EN 352-10:2020, Directive 2012/19/EU, Directive
-
2011/65/EU & (EU)2015/863, and Radio Equipment Directive 2014/53/EU.
-
The full text of the declaration of conformity is available at ISOtunes.co.uk/manuals.
-
UK & Europe
-
North America
-
Monday-Friday 9-5 ET
-
Haven Technologies, Inc.
-
873 W. Carmel Dr.
-
Carmel, IN 46032, USA
-
Haven Technologies DE
-
Winterhuder Weg 29 7. Fl
-
22085 Hamburg
-
Germany
-
ISOtunes® ULTRACOMM Aware IT-75, IT-76
-
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Version number for the manual: 1.0 Creation Date: 12/19/2022FCC ID: 2AJRDIT-75IC: 29416-IT75
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>