Trust AWST-6000 Wireless Motion Sensor User Manual

: June 9, 2024
: Trust

Table of Contents

Safety Instructions
TRUST SMART HOME
Trust Electronics Ltd.
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Trust AWST-6000 Wireless Motion Sensor User Manual

Safety Instructions

Product support: www.trust.com/71013. Warranty conditions: www.trust.com/warranty To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete Never use Trust Smart Home products for life-support systems. This product is not water-resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: -6.60 dBm. Radio transmission frequency range: 433,92 MHz

Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations.

Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to Directive 2012/19/EU.

Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations.

Trust Electronics Ltd. declares that item number 71013/71013-02 is in compliance with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: www.trust.com/compliance

Trust International B.V. declares that item number 71013/71013 02 is in compliance with Directive 2014/53/EU – 2011/65/EU. The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

Open the motion sensor
Use a thin screwdriver to detach the sensor from the frame. 2.
Install transmitter batteries
Place 2x 1,5V AAA alkaline batteries in the battery compartments. The polarity should match the symbols on the holder.
Assign code to a Trust Smart Home receiver
Assign this transmitter to the memory of one or multiple receivers, by sliding the LEARN switch from [DEL] to [SET] to send an ON-signal. Read the receiver’s manual for the code learning procedure.
Set light sensitivity
Slide the [R] switch to select 1 of the 3 light sensitivity levels. [H]: Sensor is always active. [M]: Sensor is active when the environment brightness is less than 20 lux (late afternoon). [L]: Sensor is active when the environment brightness is less than 10 lux (late evening). If you want to control chime ACDB-6500C, always choose [H].
Set switch-off delay
When no more motion is detected, the transmitter automatically sends an OFF- signal after 5 seconds or 1/5/10 minutes.
Set detection range
Slide the [ ] switch to select 1 of the 3 detection ranges.
- [1M]: 1-3 meters
- [3M]: 1-5 meters
- [6M]: 1-7 meters
Set detection angle
The horizontal detection angle of the sensor is maximum 80° and minimum 20°. Remove, reposition or adjust the size of the plastic screens to change the detection angle. Next, affix the transmitter using screws or double-sided tape.
Affix the transmitter using screws
Screw the base of the wireless motion sensor onto a flat surface, e.g. a wall.
Press the frame back onto the base and press the sensor into the frame.
The sensor needs 30 seconds to analyze its environment, before it becomes operational.
Affix the transmitter using double-sided tape
Apply double-sided tape to the back of the wireless motion sensor.
Stick the wireless motion sensor onto a flat surface, e.g. a closet.
The sensor needs 30 seconds to analyze its environment, before it becomes operational.
Delete code from Trust Smart Home receiver memory
Read the receiver’s manual for the single code deletion procedure. Slide the LEARN switch from [SET] to [DEL] to send an OFF-signal

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:

Model: AWST-6000 Wireless motion sensor
Item number: 71013/71013-02
Intended use: Indoor

is in compliance with the essential requirements and other relevant provisions of the following directives:

ROHS 2 Directive (2011/65/EU) RED Directive (2014/53/EU) The full text of the EU declaration of conformity is available at the following web address : www.trust.com/compliance

TRUST SMART HOME

LAAN VAN BARCELONA 600 3317DD DORDRECHT NEDERLAND
www.trust.com

Trust Electronics Ltd.

Sopwith Dr, Weybridge, KT13 0NT, UK. All brand names are registered trademarks of their respective owners. Specifications are subject to change without prior notice. Made in China.

TECHNICAL SPECIFICATIONS

Codesystem	Automatic
Power	2x AAA 1.5V alkaline battery (not included)
Size	Hx WxL: 80 x 80 x 27 mm
Detection Angle	Horizontal: 20-80°; Vertical: 65°
Detection Range	± 6 m
Turn Of Timer	5 sec or 1/5/10 min