Laney BCC-MONOLITH Black Country Customs Range Boutique Distortion Pedal User Manual

Laney BCC-MONOLITH Black Country Customs Range Boutique Distortion Pedal

User Manual

INTRODUCTION

The Black Country Customs range of guitar pedals are born out of the desire to achieve the best guitar tone possible.
The result of hours of dedicated testing and listening, each Black Country Customs pedal is built using the highest quality components and engineered to last a lifetime on your board.

What is the MONOLITH

Designed to give the player total command and control over a spectrum of different gains and harmonic dis- tortions from Classic fat rock tones, to jangly indie lines and everything in between.
The MONOLITH delivers expressive gain even at low levels.
With a very pleasing dynamic response to pick attack the harder you dig, the more expressive it gets. Even at high gain levels, when you hit it hard you can still hear every note of big chords and the nuances of intricate lead lines.

FEATURES

Each of the BCC pedals have been designed to incorporate features that really matter :-

• Transparent fully buffered operation at all
• Super high output drive provides an excellent interface between bass guitar and effects pedals/amp.
• Much reduced cable
• Consistent bass guitar volume performance at all
• Signal phase
• Excellent consistent load for passive Volume
• Ultra-low noise
• Silent
• Low battery LAYOUT

The layout of your pedal has been ergonomically designed by players, for players, to give you control over all the features you need, quickly and effectively.
The following pages will give you an insight into how the controls on the MONOLITH work and interact with each other.

CONTROLS

CONTROLS

DISTORTION

Sets the amount of Distortion and sustain avail- able. The MONOLITH is dynamic and expressive and responds to your pick attack. As you dial in more gain you get more compression and sustain.

RANGE

Adjusts the low-end content before distortion is added to the signal. Using the Range control allows you to tighten up the bottom end of your tone and cleans up muddy sounding pickups and high gain settings.

0 = Full range
10 = most low-end reduction VOLUME
Adjusts the output level to balance sounds or push an amplifier harder into natural distortion with a lower level of distortion dialled in.

CONTROLS

MODE

The MONOLITH can be configured to run in 1 of 3 modes available Mode D1 – Orange LED
Heavily compressed distortion, smooth sounding without loss of definition.
For players who like a more compressed sound. Mode              D2 – Blue LED
A soft compressed distortion.
A more expressive distortion with adaptive, even harmonics at lower guitar levels. Allows you to “dig” more into the note and runs less hard compression.

Mode O/D – Purple LED.

A more traditional overdrive distortion. Good for boosting your overall sound level or pushing the front end of tube amps harder.
Very little compression in this mode so your amplifier or following effects will do most of the tonal colouration for you.

CONTROLS

TONE

Adjusts the overall tonal response of the pedal from smooth and warm all the way to bright and cutting lead tones.

FOOTSWITCH

Engages the MONOLITH.

OPERATION

Install a good quality 9V battery into the pedal by unscrewing the base of the pedal and fitting the battery securely to the battery connector and then replace the base of the pedal.
Do not use excessive force to tighten up the 4 base plate screws as this could damage the screws.
When not in use it is always a good idea to remove the input jack from your pedal to prevent any unwanted battery power loss.
Caution – when you do not intend to use the pedal for a long period of time, it is always advisable to remove the battery to prevent current loss and battery leakage.
Alternatively – and highly recommended is the use of an external good quality AC 9V PSU.

SPECIFICATIONS

Model : Boost FX Type : Distortion Input Impedance : 1M
Output Impedance : 100Ω
Recommended Minimum Load Impedance : 10KΩ
Power Supply : Regulated 9V DC PSU (Not In- cluded), centre negative, 2.1x10mm connector type Internal 9V PP3 battery included (alkaline recommended)
Current Consumption : 10mA
Battery Life : 30 hours – this will vary on use and selected battery
Unit Dimensions : 58.5 x 74 x 121.55mm, 2.3” x 2.9” x 4.8”
Net Weight : 0.38Kg, 0.8lbs

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference
• This device must accept any interference received, that may cause undesired operation.

Warning: Changes or modification to the equipment not approved by Laney can void the user’s authority to use the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This product conforms to the requirements of the following European
Regulations, Directives & Rules:
CE Mark (93/68/EEC), Low Voltage 2014/35/EU, EMC (2014/30/EU), RoHS
(2011/65/EU), RED (2014/30/EU), ErP 2009/125/EU

In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the WEEE (Waste Electrical and Electronic Equipment) directive applicable in your country.
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Laney Electronics Ltd. declares that the radio equipment is in compliance with Directives 2014/53/EU, 2011/65/EU,2009/125/EU
Full text of the EU declaration of conformity is available at the following internet address: support.laney.co.uk/approvals

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>