globe 50079 Smart Retrofit Lighting Kit User Manual

globe 50079 Smart Retrofit Lighting Kit

Thank you for selecting Globe as your smart home solution. With proper care, this product will provide years of pleasure and enjoyment.

SMART RETROFIT LIGHTING KIT

Check out the installation video on our website: globe- electric.com/smart

SAVE THESE INSTRUCTIONS

SAFETY PRECAUTION: Please read and understand this entire manual before ttempting to assemble, operate or install this product. Before assembling your lighting fixture, TURN OFF POWER and consult a qualified licensed electrician. Most electrical accidents are caused by carelessness or ignorance. If you combine a basic knowledge of electricity, a healthy respect for it, and a dose of common sense, you can safely tackle many household electrical repairs. Here are some basic guidelines for working with electricity:

• Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work.

• Before touching any wire, use a voltage tester to make sure it’s not live. Whenever you check for voltage in a receptacle, check both outlets-each may be controlled by a separate wiring circuit.

• To protect children, place safety covers over any unused outlets.

• Always work with enough light to see what you are doing; it’s easy to make mistakes when you’re working in dim light.
  Before assembling your lighting fixture, TURN OFF THE POWER and consult a qualified licensed electrician.

• WARNING – Risk of fire or electric shock Install this kit only in the lighting fixtures that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the lighting fixture. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

• WARNING -To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

• CAUTION: SHOCK AND RRE HAZARD, DO Nar USE WHEN ENCLOSURE IS BROKEN. TlllS DEVICE IS Nar INTENDED FOR USE wnH EMEROENCV EXITS.

• This luminaire has been modified to operate LED lamps. Do not attempt to install or operate incandescent lamps in this lighting fixture.

• COVERED CEIUNO MOUNT ONLY. THIS RETROFrr KIT IS ACCEPTED AS A COMPONENT OF A UOHTINO FIXl’URE WHERE THE SUITABILnY OF

• TllE COMBINATION SHALL BE DETERMINED BY AUTllORITIES HAVINO JURISDICTION. surrABLE FOR TYPE IC WMINAIRES. SUITABLE FOR USE

• IN ENCLOSED RECESSED LIOHTINO FIXl’URES.
  Always connect the grounding lead to fixture, where applicable.

LIMITED WARRANTY

• This smart recessed light is warranted to last 2 years from the dateofpurchase based on use of 3 hours per day. If it fails before that time, we will replace it. Send the recessed light, proof of purchase and register receipt along with your complete name and address to Globe Electric. See caution text for proper use. This warranty is void if this product is misused in any way. This replacement is the sole remedy available and liability for incidental or consequential damage is expressly excluded. This device is not intended for use with emergency exit fixtures or emergency exit lights, photocells and electronic timers.
• This device complies with Part 75 of the FCC rules. Operation is subject to the following two conditions: (l) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this product are not expressly approved by the party responsible and cou Id void the user’s warranty of the equipment.
• NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 75 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the distance between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

RF EXPOSURE:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.

USER MANUAL NOTICE FOR LICENSE□EXEMP T RADIO APPARATUS:
This device complies with Industry Canada license□exempt RSS standard(s). Operation is subject to the following two conditions: (7) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-005 (B).

RADIATION EXPOSURE STATEMENT:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &your body.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 75 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
WARNING:
RISK OF FIRE OR ELECTRIC SHOCK INSTALLATION OF THIS RETROFIT KIT REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE LUMINAIRE’S ELECTIRICAL SYSTEM AND THE HAZARD INVOLVED. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTIRICIAN. PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS. USE THE RECESSED LIGHT WITH A MINIMUM LAMP COMPARTMENT DIMEN SION OF 727mm x780mm ONLY.

FCC RESPONSIBLE PARTY
Globe Electric
2264 East 6th Street
San Bernardino, CA 92470
www.globe-electric.com

FEATURES

• LED integrated – dimmable through the app
• RGB: Choose from a full spectrum of colors
• Tunable white (2000 K – 5000 K): Choose from a focused bright white to a relaxed sunset glow
• Set schedules and control your light from anywhere
• Fits with most 5″ or 6″ existing recessed down light models

SPECIFICATIONS

insulation
720V•60Hz| Energy Star
Indoor use only| Airtight per ASTM-E283-04
72 watt**

< I(@

|

Integrated LED bulb
Since 1932, Globe has taken pride in offering products of the highest quality, and a level of service unparalleled in the industry.
Should you encounter any difficulties, have any questions or simply wish to offer us your valuable feedback, you may contact us in the following ways:
Toll Free Telephone: l-888-543-1388 (North America Only) /Toll Free Fax: l-800-668-4562
(North America Only)
E-Mail: info@globe-electric.com
Mail: Globe Electric Customer Service Department
150 Oneida, Montreal, Quebec, Canada H9R lAS
Please visit our website to discover other quality Globe products: http://www .globe-electric.com

PRE-INSTALLATION

Planning Installation
Compare all parts with the “Hardware Included” section. If any part appears missing or damaged, do not install this product and contact the Customer Service team at l-888-543-7388 or e-mail to info@globe-electric.com.

Tools Required

Hardware Included

NOTE: Hardware is not shown to actual size.

l

E26 socket adapter with Male connector as shown| l
rubber gasket| l

PREPARATION

Installation into existing recessed incandescent fixture with Type E26 base lamp sockets: For use with 5″ or 6″ recessed housings (Housing sold separately).
LED recessed trim will retrofit into select existing 5″ or 6″ nominal incandescent housings.

Step 1
Turn off the power to the light fixture at the main service panel.

ELECTRICAL INSTALLATION

FIG. 1. Place the wall switch to the “OFF” position.
Depending on which type of fuse box you have in your home:
FIG. 2. Place either the main (Master) switch to the “OFF” position, cutting off power to your entire home OR turn off the individual switch that provides power to where the fixture will be installed.
OR
FIG. 3. Place either the main (Master) switch to the “OFF” position, cutting off power to the entire home OR unscrew the fuse that provides power to where the fixture will be installed.

INSTALLATION

• Step1
  Remove the existing trim installed in recessed housing (if necessary) and incandescent lamp (if any). The fixture will be illustrated as shown in Figure l.

• Step2
  Check the dimension of recessed housing and the lamp socket type to be sure it is suitable for the retrofit kit before installation.

• Step3
  Check the through branch wiring markings and the existing lighting fixture rating to be sure it is suitable for the retrofit kit before installation.

• Step4
  Install (screw in clockwise direction) the E26 adapter into lamp socket as shown in Figure 2.

• Steps5
  Connect the male connector to the female connector on LED Lamp as shown in Figure 3. Check the connector carefully for tightness. Be sure that the connection should be insulated reliably with no exposed bare wires.

• Step6
  Gently push the LED Lamp into the recessed housing as shown in Figure 4. Squeeze the clips together gently to fit into the side of recessed down light housing.

• Step7
  Make sure the trim of LED Lamp is fitted into recessed housing in ceiling firmly. Steps
  Turn on the light fixture. If the light fixture is not working, turn off the power at the main service panel and check the wiring connections.

CONNECTING INSTRUCTIONS

Make sure your mobile device is running iOS 9.0/watchOS 2.0/Android”‘ 4.4 or higher.

1. Let’s get started!

   • Download the Globe Suite™ app from the App Store or Google Play to your mobile device

   • Launch the Globe Suite™ app

   • To register, enter your email address, create a password, then log in to the app
     OR

   • Log in if you already have an account

2. Verify your network

   • Verify your network and ensure your mobile device is connected to a 2.4 GHz Wi-Fi channel
   • Consult your router documentation for detailed instructions on how to change wireless settings

3. Scan mode

   • Power on your device
   • Select the”+” symbol on the top right hand corner
   • Follow instructions within the app
   • If your device is flashing rapidly and fails, try using EZ Mode

EZ mode

  * Select the”+” symbol on the top right hand corner
  * Select “Manual”
  * Select your product type and follow the instructions within the app
  * If the connection fails, try using AP mode

AP mode

  * Select the”+” symbol on the top right hand corner
  * Select 11Manual”
  * Select your product type
  * Open the menu on the top right hand corner and select “AP mode”
  * Follow the instructions within the app

4. Set up voice assistance
   • Select “Profile,• and select “Integration”
   • Select your voice assistant and follow the instructions within the app

Did you know?
Most modern routers are dual-band, meaning they support both 2.4 GHz and 5 GHz channels. The most common wireless options are:

• Mixed: The router will broadcast both 2.4 GHz and 5 GHz simultaneously under the same SSID. The device will choose which to connect to based on multiple variables (congestion, distance to router, etc.).
• 2.4 GHz: Broadcast only on this channel
• 5 GHz: Broadcast only on this channel
• Dual 2.4 and 5 GHz using Separate SSIDS: Router will broadcast both channels and user manually decides which to connect to

HOLE SIZE

References

• Electric | The Largest Consumer Energy & Renewables Platform

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>