SAMSUNG CBAS210R Central BLE Module User Manual
- June 9, 2024
- Samsung
Table of Contents
SAMSUNG CBAS210R Central BLE Module
Device name:
Central BLE Module
Model name:
CBAS210R
General Information
- Shape: PCBA Module type
- Comm. Protocols: BLE
- Weights & Dimensions: Width 20 Depth 35 Height 2.9 mm
- Product Weight: approximately 2.6g
- Operation Temp: -20 ℃ ~ 70 ℃
- Power Source: DC 5.0V
The CBAS210R is a BLE Transceiver for electric stove networks. Connected to the electric stove ventilator, it acts as a pathway between remote home automation.
Networking
- The CBAS210R has applied the RTL8762CMF BLE Transceiver of Realtek.
- The BLE transceiver delivers the information received from the remote control device to the main board with a 5-pin connector.
Power source
The CBAS210R is powered by an external 5.0VDC@2A regulated power source with a
5-pin connector.
Expansion Ports
The 5-pin connector connects the main control board.
Electrical Properties
| Parameter | Description |
|---|---|
| Modulation type | GFSK |
| Modulation rate | 1Mbps, 2Mbps 125kbps, 500kbps |
| Channel interval | 2MHz |
| Antenna gain(Pattern Antenna) | 1.56dBi |
| Occupancy bandwidth | ≤2MHz |
| Frequency range | 2400MHz ~ 2483.5MHz |
| Carrier frequency tolerance | ≤20×10-6 |
Notice FCC/IC Statement
Approval Statement
FCC approval
This device complies with Part 15 of the FCC`s Rules. Operation is subject to
the following two Conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesirable operation. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
The host device must be labeled to display the FCC ID of the module, for example:
Contains Transmitter module FCC ID: A3LCBAS210R
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
- The OEM integrator is responsible for ensuring the end user has no manual instruction to remove or install the module.
- The module is limited to installation in mobile or fixed applications.
IC approval
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The host device must be labeled to display the Industry Canada certification number of the module.
- Contains transmitter module IC: 649E-CBAS210R
FCC/IC RF exposure statements:
This device complies with FCC & IC radiation exposure limits set forth for an
uncontrolled environment. This module may not be co-located with any other
transmitters or antennas. The antenna must be installed such that 20cm is
maintained between the antenna and the users.
User Information
Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user`s authority to operate this equipment.
IMPORTANT NOTE FOR OEM INTEGRATOR
This is a single module that has been tested and complied with Part 15.247,
and RSS-247 requirements. The host device needs to be labeled with the
module’s FCC/IC IDs, for example, “Contains Transmitter module FCC ID:
A3LCBAS210R, IC:649E-CBAS210R “.
This device is intended only for OEM integrators under the following conditions:
- This module may not be co-located with any other transmitters or antennas.
- The antenna must be installed such that 20cm is maintained between the antenna and the users.
- Only the antenna type and antenna gain documented in the module FCC/IC reports can be used.
As long as the above conditions are met, further tests or certifications will not be required. However, the OEM integrator is still responsible for host product evaluation or any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module, and obtaining separate FCC & IC authorizations.
Additional testing, Part 15B disclaimer
This module only complied with FCC 15.247 requirements as listed on the grant,
and therefore, the host product manufacturer is responsible for FCC Part 15B
compliance testing with the module installed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>