COVANA Evolution Automated Hot Tub Cover User Guide

Automated Hot Tub Cover
User Guide

Evolution Automated Hot Tub Cover

Pre-Delivery Guide
Preparing the way for your new Covana spa cover

No limit to cover your hot tub!
Thanks to its modularity, the Evolution cover is compatible with most large and round hot tubs.

Less effort, more comfort for a longer time:
A promise signed Covana.

Spa compatibility

Most square, rectangular, or round hot tubs with a flat surface (no protruding headrests) of up to 93″ x 134½” with a height between 34″ and 48″.
The dimensions of the Evolution models are illustrated below. The dashed line dimensions include the recommended clearance for maintenance. The entrance of the spa will always be placed on the width side.

Refer to the table below to choose the appropriate model according to the dimensions of your spa.
If you don’t know which model to choose, or if you are unsure whether your spa will fit under the cover or not, please contact Covana for the Technical Support department: 1-877-278-8010.

Evolution lEngth| Spa maximum width| Spa maximum lEngth|
---|---|---|---
8 ft| 92¾”| 98″|
9 ft| 92¾”| 110½”|
10 ft| 92¾”| 122½”|
11 ft| 92¾”| 134½”|

• For spas of maximum length and width, the ground clearance height and the corner radius must be at least 4″.

The seal of the cover will have to be installed on a flat surface of at least 1″ wide, on the acrylic of the spa. The minimum turn radius of the seal is 4″. Ensure the seal will be able to go all around the spa while continuously touching the cover.

Color options

For a slight extra on the price of the regular white pannel, this option allows you to better match the color of your Covana with your environment. A little detail that can make a big difference.
Customize your cover by choosing between the following options:
(Actual colors may vary from images shown.)

ColorS|
---|---
Mocha/Latte|
Mocha/White|
Slate/Platinum|
Slate/White|

Retractable shades

The shades provide additional protection from the wind and harsh elements. Most importantly they provide coveted privacy from curious onlookers.

ISLAND| **| ZEN| **| SUNSCREEN|
Width side| | Width side| | Length side|
Length side (8 ft only)| | Length side (8 ft only)| | Width side|

Opaque mochatop gun| **| Opaque Slatetop gun**|
8 ft| Length side| | 8 ft| Length side|
Width side| | Width side|
9 to 11 ft

| Length side| | 9 to 11 ft| Length side|
Width side| | Width side|

Choosing the perfect location

• The Covana cover can be installed either indoors or outdoors.
• Away from flood zone, water downpours or debris falling.
• Wind speed should not exceed 30 mph in the raised position.
• Operating area must be free from obstacles, i.e., branches or electrical power lines.
• Allow for safe access to the spa, free of obstacles or debris.
• Sunlight must not converge or be directly reflected on the cover such as the reflection from a window.
• The installation area must be clean and free of any vegetation (i.e., grass, branches, roots) and mineral contaminants (i.e., rocks, dust, sand).
• The key switch must be permanently mounted and located 5 ft away from the spa and 5 ft above the deck or ground level in a location where no water downpour or debris could fall on it.
• The user must have a clear view of the cover when operating it (25-ft cable).

https://youtu.be/VRJ_eB3u8a0

Laying the right foundation

• A clean, flat and level surface such as an engineered wood deck or a concrete slab is needed.
• The foundation must be able to support at least 600 lb.
• Any water accumulating around the cover will have to be drained.
• Allow for at least 24″ of clearance for maintenance on the motor and entrance sides, and 6″ on the other sides.
• The four jacks will have to be properly anchored to the foundation (anchors not included).

Minimum base size
Contact Covana if the foundation is already in place and its dimensions are smaller than those illustrated below.

Electrical specifications

• All electrical work should be done by a certified electrician, otherwise the certification and warranty will be void.
• The cover must be installed in accordance with and comply with all applicable local codes and regulations.
• Wires and conduits should be sized according to local codes and regulations.

The cover requires a dedicated single-phase 115 VAC (North America) or 230 VAC (Australia/Europe/New-Zealand) hard-wired power supply.
North American requirements

Australian/European/New-Zealand requirements

Planning the delivery

The Evolution cover will be delivered in a wooden crate. Take the time to sketch out a simple map from the delivery point to the installation point for the delivery personnel. You can also disassemble the unit from the crate at the delivery point and move the parts by hand.

Dimensions and image for reference only.

Use this simple checklist to plan the delivery route.

 automobiles/recreational vehicules
 gutter/facia/soffit overhang
 electrical/gas meter equipment
 doghouse/playhouse
 stairs/steps/railings
 uneven ground
 slippery slope or path|  trees/foliage/shrubs
 patio furniture/deck chairs
 fences or narrow gates
 gravel, rocks or wood piles
 adequate access to wood decks
 door openings (if applicable)
 sheds or built-in structures
---|---

Notes: ——————-

Your heaven of relaxation and privacy
The manufacturing process and the choice of materials lend COVANA products exceptional quality, performance and durability.

For more information, contact
Covana or visit our Web site:
covana.com
info@covana.com
COVANA is a member of the Canimex Group,
committed to excellence since 1969. 247645 Rev 1
Printed in Canada

Documents / Resources

| COVANA Evolution Automated Hot Tub Cover [pdf] User Guide
Evolution Automated Hot Tub Cover, Automated Hot Tub Cover, Hot Tub Cover, Tub Cover, Cover
---|---

References

• Covana | Automated hot tub covers | New

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>